How to Build an All-Wood Takedown Bow

Shatterproof Archery
117 followers
We are for you - Stay Shatterproof!
DIY ALL WOOD Takedown Kit: https://www.shatterproofarchery.com/products/diy-wood-takedown-bow-kit
Archery Questions? We would love to help: [email protected]
https://www.shatterproofarchery.com/
Shatterproof Archery is a small company located in Colorado Springs CO.
We are dedicated to helping more people enjoy more archery.
#shatterproof
#bowmaking
#traditionalarchery
I set the beer at 10:31 for the shoot.
No one's here. Bamboo hickory for the
limbs handle. Take down hardware.
Flemish twist bow string handle. Dude,
is this thing on? It's sick. Oh, wait.
There's some dust.
It's all you need to build this boat.
Bamboo is a big wee. Uh, it's green. I
also wrote a book with infographics,
detailed photos, dimensions, diagrams,
everything you need as an instructional
manual to build this bow. Cass
Cass,
I sourced all the materials putting it
together in a kit for your convenience.
You do not need this kit to build this
bow. You do not need this book to build
this bow. You just need this video. I'm
hungry. We hope you enjoyed the video.
This is a threepiece wood takedown bow.
I am super interested in making the best
bows I can and I am super interested in
helping you make the best bow that you
can. And after making hundreds of
fiberglass bows, this is my favorite
design that I've landed upon. That
curiosity brought me to wonder if I
could make the exact same bow design but
with wood. This is a three-piece wood
taked down bow in the same design as my
favorite fiberglass bow. I had to make a
few modifications to make it work from
wood. You see, there's three things we
need to build. A riser and then two
limbs. I've constructed this entire
build so you can get all the materials
for under $100, which is amazing. And as
a matter of fact, you might even get it
for less than that.
So, here's all the material you will
need. And then next, let's start on the
riser. First, you'll need some sort of
material for the riser. It needs to be 3
and 1/2 in tall, at least 14 in long,
and 1 and 3/4 in thick. In this
scenario, I'll take two boards and put
them together. But the cool thing here
is that if you have scrap wood like I
do, you can add really cool accents and
laminate it however you would like. But
I do recommend a harder wood like
hickory or ash, or there's a ton of
exotic woods that I've built with that
are harder. The reason is these limb
bolts need to be strong enough to hold.
So you're going to screw an insert into
the riser and the limb bolts need to be
strong enough. I've tried a softer wood
like a spectral ply which is a bunch of
like birch laminated together and that
was too soft. So I wouldn't use pine or
popler or anything that's super soft,
but I would definitely recommend harder
wood in the handle. The strongest and
most perfect scenario, which isn't
necessary, is to have laminations this
way as well as a curved lamination this
way. So the insert goes beneath the
curved lamination and is inside to
there. So it's technically with inside
of three pieces of phenolic which is
really strong material. So with this
type of riser I'll test it later but I
think I can go up to near 100 lb bow.
Next for the limbs you'll want a piece
of bamboo. This is a bamboo slat. Also
I'm going to use a piece of hickory. In
the last video I made it from oage. You
could do this from many types of wood,
but I would recommend hickory for the
cheapest, quickest, easiest way. Then
I've got two extra pieces of scrap wood
for the fade outs from the handle into
the limbs. I'm going to use Typon 3 wood
glue today. You could use EA40, but it's
not necessary, as well as a pack of
limbbolt hardware. You can accomplish
this entire project with an assortment
of hand tools. I'm not going to just use
hand tools today because speed's
important to me so I can put out more
videos. But I'll give you the
alternative to the tool I'm using and
what I would do if I were using hand
tools. Don't let your tools limit
yourself. You can be creative and figure
it out. That's what I did when I first
started bow making in an apartment. I
started with just this and a pocket
knife. I'm doing a 3 1/2x 14 and then
this is actually 2 in thick and I'll
thin that down later. These spring
clamps are super handy. They're not
super expensive and you can get like a
20 pack really cheap online and you can
use these for the limbs as well as the
riser. I live in a super dry environment
so this wood will soak up the glue a
ton. Therefore, I like to do what I call
as a sizing coat. I'm going to spread
glue across the entire surface and let
it sit for about 3 to 5 minutes and then
I'm going to reput glue on. And I'll
time-lapse this so you see how much the
glue just soaks into this wood. Some
people say this helps, other people say
it's been tested and proven it doesn't.
But I think it does help with the
premise of not having a dry joint. Now,
I put a ton of glue on, but if you look
here closely, it's completely basically
soaked all the way in in a couple spots.
So, let's add a little bit more and then
clamp it together. The key is no dry
joint. Slap those together and then
let's clamp it down.
They'll slide a little bit on the first
couple. No biggie. As long as your
boards are flat, it doesn't take much.
So, let's let that glue cure. In the
meantime, we can work on the limbs.
That's a cool part about the three-piece
takedown bow is there's pretty much
always something to work on. Now, this
is a bamboo slat. It's crowned on the
top, and these are the nodes. I'm not
really going to pay attention to the
nodes. Not a super big deal today. But
on this other side, we need to make it
completely flat. So, we can marry
together two pieces of wood. One's going
to be the hickory, one is the bamboo.
It's technically a grass, forgive me.
But we need them flat so that we can put
them together. This is going to add
strength, a lot of strength. This is the
magic sauce that allows the limb bolts
to go in because this doesn't have grain
like wood. It's more like a sponge that
allows the forces of the limb bolts to
hold. If you just try this with plain
hickory, I can almost guarantee that's
going to split out on you. This is the
magic sauce. You can change the hickory
to many other types of wood that are
good under compression, but I would
absolutely recommend to use bamboo. I'm
gonna take this slat and hold it evenly
on the belt sander and go back and forth
until I get it completely flat. If I
didn't have that massive belt sander,
I'd use a smaller one like this or even
one like this. I've recommended this
when one a lot for beginners because it
allows you to throw a belt on as well as
spindles and it's really cheap.
And for those who just have hand tools
or just want to use hand tools, this is
how I would do it. Take a cabinet
scraper. It's like a $5 piece of metal.
Sharpen it up.
If you have a vise, it's really handy.
What's happening is the cabinet scraper
is touching on both sides, but not the
middle yet. But it's a great way to
remove the bamboo evenly. It's gonna
take more work, but in about 30, 45
minutes, you can have this whole thing
done.
I'll get it down to flat so you can see
what it's like.
All right. Now, if you take a look, you
can see how I've worked all the way
through. Now, it's flat. Can be done
with a scraper. belt sander will save
you a little bit of elbow grease as well
as 30 minutes. I go on the edge of the
belt sander. I use light pressure, not
hard, light pressure, and always have
the piece moving back and forth. If you
use hard pressure or don't move the
piece, it'll create a divot into your
bamboo and then it will not have a clean
glue up later. Always be moving. Always
nice, gentle, light pressure.
I highly recommend using your fingers
and you can feel any part of the bamboo
where there might be a dip. This is the
There's a little dip right there. I'll
smooth that out. This is the best way to
not have a bad glue joint. Your fingers
can detect what your eyes can't see
sometimes. So, how thick should you
leave it? Somewhere around 2/10 of an
inch is going to be pretty good for any
bow between 30 and 60 lbs. I did build a
100 pound bow and I left that one a
little thicker, closer to a/4 in. But
depending on how steep your crown is, it
can change. I'd recommend bringing it
down to about a fifth of an inch. Nodes
always a question. How evenly should I
space them? Is that important? What
should I what should I think about
there? Evenly spaced nodes makes
tillering easier, but it doesn't
necessarily make the bow perform better.
We're having 32-in limbs, so I'm going
to find an even distance between the
nodes where I can go 32 in on either
side. Then I'll cut it there for each
limb. The most important thing with this
bow is that our limb bolts don't fall
exactly where a node is. So you also
hear there was a node right here. So I
cut on just on that side of it so that
the limb bolts, not where the node is.
And then the first node is down here
past the fade out. Same thing on this
side. So from this node, I have 37 in in
one direction and I have 34 in the other
direction. That's perfect. So I'll cut
my line right on this node. This side
connects to the riser. So I'll measure
down 32 in. Make my mark and cut them
both there. Bamboo's prepped. Now for
the wedges. I've already cut these down
to a decent size. We're at 8 in long.
That's important. And I've thinned them
to 1/10enth of an inch on the sander.
So this piece will be this piece. It's a
critical piece to work. It stays thick
for these first 3 in. And then it
gradually, super gradually tapers and
feathers into the limb. What this allows
the bow to do is not to bend in this
area. You'll see the total thickness is
3/4 of an inch right here, but at the
end of the fade out, it's/ an inch. So,
this piece gives the strength we need
here to not have it break. Therefore,
I'll mark at the 3-in mark. And I'll do
the same on this limb. Don't touch
this area. We want it flat. Also,
don't touch the back.
We want this side flat, but we want the
bottom flat so that it stays flat along
the core material. This is an
exaggeration to show you what I'm
trying to do. That's what the wedge is
like. Flat on this side.
Don't touch these first three inches.
This is a properly feathered piece. And
you can see how gentle this bends. It's
paper thin. And then comes back to our
one10enth of an inch. I forgot to
mention that this type of material
doesn't matter. I've tested fiberglass.
I've tested bamboo. I've tested soft
woods. I've tested hard woods. I've
tested all sorts of things and I would
choose the the insert that gives you the
look you want. So, I thought it'd be
cool to add a dark accent in these
limbs. So, I did walnut and it's scrap I
had. The risers curing, the bamboo's
ready to go. The
fade outs are ready to go. Now, it's
time to work on the hickory. Hickory
stays like this can be picked up online
or at a hardware store. This one is so
thick, we need to thin it down. I'm
looking for a finished dimension of 4/10
of an inch on this hickory stave. So,
with this one, I'm going to take it to
the bandsaw, cut it up the middle, and
that should allow me to have two pieces.
The reason I'm not leaving it this thick
is because I want to add a little bit of
reflex into this bow to help it shoot
even better. So, the limbs need to be
thin enough that they can bend without
breaking in the glue up process.
Additionally, once it's split in half,
that allows you to make two full bows
out of this one 15, 20, $30 piece of
wood. My favorite tools for flattening
it after sawing it would be a drum
sander. Most people may not have that,
so a planer actually works really well.
Or just on the belt sander to prep it
for the glue up, you can do that as
well. Hand tools, of course, will work,
but just take more time.
Good news. Now we just need to cut this
down to 32 in to match the length of our
bamboo. Something I've always done for
bow making is to use a hacksaw because
the teeth are so fine.
It allows me to never have split out.
And now we're back with our riser, our
bamboo, our limb fade outs, and our
hickory. That's all the pieces we need.
Now it's time to glue it up. Here's how
I do it.
First, the better these pieces match up,
the easier it's going to go for you. So,
I'll place all of these down together
and I'll line it up as good as I can and
add some spring clamps. Now, I can run
this to the belt sander and true up the
edges. I want to add some reflex. So,
this is my setup. The blocks are 31 in
apart from the insides. This right here
is 1 in and these ones right here are 2
in tall. So that allows us to take our
board after the glue is on it and we can
reflex this down just like that. And
then we'll add our clamps. So this was
what would be called a dry run.
Everything's lined up. Make sure
everything looks good. Now we just need
to add the glue and do this again. First
thing is when you're setting up the form
here, you don't want these to move
around because when you push the bow on
it, it can move it. I'm putting the
blocks at 31 in apart. And then I'm
going to screw them in from the bottom
so they can't move.
Now with our 1-in block, we want it to
be right in the middle. Now, nothing's
going to move around on you, and the
glue up's going to be much smoother. I
do like to clean my pieces with acetone.
Everything's cleaned up and ready to go.
I will do a sizing coat first. Again,
just an initial thin layer. After a
minute or so, the final coat. I'm using
Typon 3 wood glue here. Any yellow wood
glue works great. This one is supposed
to be waterproof, so I guess that's a
good thing, but I finished my bows
anyway, so I don't necessarily need
waterproof glue. Yes, you could use hide
glue. You could use EA40. You could use
Uniond, but wood glue is one of the
best. I like to air with too much glue
and too many clamps. All right, let's
clamp it up. First, I'm just going to
lay it down. Throw a clamp on. Awesome.
Okay, so that's starting to set
together. Now we can go for the middle
clamp. I think this is a spring clamp
will be good enough there.
There we go. And then I like to clean
some of the squeeze out just to keep it
clean. If you go ahead and get a rag and
wipe the glue off before it hardens,
um it's going to be a lot less clean up
later.
I will add a little bit of a tighter
clamp at the fade out.
and any place that looks like there
could be a gap. The reason I'm using
clamps
rather than wrapping it in some sort of
elastic is because wood glue needs air
to cure. If you use EA40, you can wrap
the entire piece in some sort of elastic
or bike tire like this and it'll cure
based on the chemical reaction of the
epoxy's mixing. But if I were to wrap
this in saran wrap or the bike tire,
this glue would never cure. It really
doesn't need to be over complicated.
There are hundreds of ways to glue
something up. You take the principle of,
okay, these pieces need to be flat and
they need to be pressurized. How can we
do that? There's no right or wrong. It's
fun to be creative and use the methods
that you have. So, let's do the other
one the exact same. If we flip the
script and say, what could we do to
guarantee that this would fail? It gives
us a frame of mind to figure out what we
need to solve for before we glue up.
Here's a few things to keep in mind or
to implement so that the chance of
failure goes down. Use your fingers. I
know I already mentioned this, but
really double check that this is very
flat. The mistake is that if there's
dips in your material, if they don't
come together flat, then you it's it's
really hard to get a good glue up. And
sometimes if you're not particular on
the material prep, when you push it
together, there's gaps just by holding
it into place. And I'll mimic it. It
could look like that. Now, if this is
pushed, it's good. But just by barely
touching the sander on a location you
didn't want to or putting too much
pressure, you can end up with a large
glue line. Also, the limb wedge. The
most common place in the glue up where
there's going to be a gap is going to be
at the end of the fade out of the limb
wedge for two reasons. One, you just
don't have enough clamping pressure
there. Two is because the featheredness.
It's not feathered enough. So, it's not
gradual enough coming into the limb. So,
there's a basically a steep angle there
and that's when it has a problem. And
then with your glue, make sure you have
enough glue. More clamps are better and
you will have a great glue up.
All right, so I'm just here trying to
shoot a little bit of B-roll for you
guys and I cannot get over how smooth
this shoots. I built this one about 4
months ago and it just blows my mind.
It's like for an allwood bow to be
shooting like if I didn't know, I would
be thinking I'm shooting a fiberglass
bow. I'm just saying if the goal is
smoothness,
this is one to consider.
If you're new here, thanks for stopping
by. Today, I'm going to show you how to
build a riser. My intention's been to
lower the barrier to entry to bow making
and archery for those who are
interested. And with that mission, it's
led me to do different forms of content
to help people. This right here is video
three of a six or seven video series on
how to build this awesome three-piece
wood takedown bow. Today we're covering
riser profile and shaping. This book is
the step by step with a ton of photos,
infographics with measurements. It
breaks it down to make it easy. Not
necessary. You could build this bow from
these videos. Want to give the option of
both. Shatterproof Archery also has a
kit of how to build this bow.
Hey guys, great news. I got one limb,
two limb curing. Now, with the Typon 3,
it only has to sit for an hour and then
you can work with it. You just don't
want to stress it for 24 hours. This has
been sitting for four hours. So, we're
going to go ahead and take the riser and
start building it. Has the limbs cure.
I've tested out a bunch of different
riser designs. And here's some. This one
here, this one, this one, this one, this
one, this one. But this one is the one I
really like. And we're carrying these
principles to this. This one's the same
as well. So, I drew this to help you
out. But you'll notice I've got some red
lines and then two blue lines. We're
going to pay attention to the blue
lines. On one side of our block, it's
going to be flat. And you'll see this
bottom side. It'll be flat all the way
across. So, we can measure from this
flat line. We're going to come 1 in up
here, 1 and 1/2 in up here. It's going
to be 3 in along that bottom line where
this mark comes up. That's going to
establish the proper angle for the limb
to come off the riser. That's all the
importance. one and a half, one, three.
I have built this two different ways.
One is with a 16inch length. The other
is with a 14inch length. You can do
whatever you would prefer. These shapes
are up to you. Something I like to do is
that the depth of the handle is going to
be in line with where the limb comes off
the riser. So, if you put a straight
edge across, you'll see right coming
into the depth of the handle is right
where the limbs are coming out. That's
going to make sure that this style of
bow is extra smooth. So, we've got our
block. Let's flatten one side first.
3 in 1 and 1/2.
The last thing I did not mention is
where to make the center line. So at 7
in, that's my center. I'm going to go
ahead and draw this across. What do we
want the center to be? You could make
the center the arrow shelf. But what
works for the smoothest shooting bow is
to make the center the deepest part of
the throat of the handle. So I can take
these marks like we discussed earlier,
and now I know I want the handle deepest
part to be right in there. And I'm okay
with it going a little further that way.
So, I'll go about a/4 inch further in
this way. Okay. So, that is the deepest
part of the handle, which means the
arrow rest is going to be above it,
which means I'm just going to kind of
eyeball how I would want that handle to
feel. Now, this might not look like
anything to you, but let's bring this
out this way because we're going to have
more of a forward- facing handle like
that. These curves don't have to be
precise. It's just personal preference.
So, you can take your time as you remove
material. I've done this design so many
times, I can eyeball it and I know what
to look for and what to avoid. The other
thing to notice on the layout is I
purposely did this to where this chunk
that's chipped out is over here where
I'm not going to use that material. So,
take a look at your board. Make sure if
there is any imperfections or any knots
you want to avoid, you want to take out
this, this, and this. Now, with your
choice of tools, remove everything you
need.
Heat. Heat.
[Music]
Heat.
[Music]
Heat.
[Music]
[Music]
Now, here's an idea to make a cool
looking riser, or at least a different
looking riser. So, I'm taking one of my
hickory risers, but I'm going to torch
it. Any propane torch will work. But
before you torch it, it's important to
get the riser to the exact shape you
want because we're not really going to
change the shape after we darken it. How
I do this is I go ahead and char the
entire piece. And then after it's
charred fairly dark, I will use 220 grit
sandpaper to sand off as much as I want
or as little as I want for the look I'm
going for. This gives it a nice unique
look. I really like how it turns out and
it's a fun way to give a different look
to a light colored material. So, when
shaping a riser, there's a wide
variability of preferences, but one
principle that I have found true for
most people is that most of us like this
to come backwards. That allows you to
grab the riser and roll your wrist up a
little bit and find that very
comfortable. So, with this style, we're
having a forward- facing handle, and
we're rolling that backside over.
Everything else, as far as the exact
curvature here, is going to feel better
depending on your hand size and how you
grip the bow. Also, there's a point
right in this area that a lot of people
find that the meat of their thumb, if
you got a big meaty thumb, kind of like
I do, uh, it it can indent there. So,
when I'm finishing the riser, I'll put
my hand on it and really get a good feel
of it. And sometimes I'll even string
the bow and shoot it and see where
there's undo pressure on my hand where
it's like, h, that doesn't feel the
best. Then you just go in there with an
orbital sander or a rasp to clean that
up. And in the end, you end up with a
really nice clean riser.
Okay, we are making such good progress
here. And now it's actually time to put
the hardware in. I don't finish the
handle completely and I leave it a
little bit bulky at this point. And the
reason being is that after we get the
limbs on, sometimes it's shifted off or
whatever. What I like to do is leave it
just about a/4 inch bulk, just a little
bit wider than I want the finished
dimension. Then when we get the limbs
on, I can take that to the belt sander
to a hand sander so that the limbs are
completely true and flush with the
riser. Then they match perfectly to that
bow and look better in the end.
ShatterProof sells these hardware kits
individually
as well as in the uh bow making kit, but
the kit consists of two threaded
inserts, two pins, two washers, two limb
bolts, and an Allen key to put it all
together. For the limb bolts, I highly
recommend building a template. This is
how you do it. So, for my template, I
have the holes at 2 in apart, and I have
this pin hole/ an inch from the edge,
which would put this 2 and 1/2 in from
the edge. But this makes it easy to put
on both sides here as well as on the
limbs. I recently got this vice to make
it easier to do take down hardware. But
if you don't have a drill press, place
the riser in a vise and then find level.
Once it's level, you can clamp it in and
then when you drill, just drill as
straight as you can. A threaded insert
will go on the side closest to the
riser. And then we'll put the pin in on
this side. With this kit, it's a 7/16th
for the threaded insert. So, let's do
that first. Instead of setting the depth
stop every time, I just use the tape
method on the drill.
[Music]
Now, for the pen, I use a 1564.
I find that this size allows me to drop
it in easily. has a little tiny bit of
play, but then I can just do a dab of CA
glue when I get everything solidified
and it'll stay in the riser. You can use
a 732, but the downside to that is you
kind of have to hammer it into place and
then it's really hard to get out, which
is fine unless you need to make an
adjustment.
Future creamer now, but I mentioned you
can hand reel it and and I said try to
keep it, you know, just try to go
straight in basically. And you may
think, "Uh, is that not precise enough?"
Well, hilariously, in that same video, I
was drilling these in, and I didn't even
line these up level at all. I I don't
know what I was doing. I was probably
thinking about filming, but I put them
like this. So, if you drop a level on
your board, you can adjust your riser.
And uh that's going to be best for best
results. If the drilling angles don't
match, then the pin just may not go in
smoothly. Now, you can counter synink
this a little bit if you want this lip
to sink into the riser. I'm going to add
felt. So, the felt's going to be the
same height of the lip. So, I'm not
going to do that on this one. These
generally come with a little Allen
wrench like this to thread them in. What
I have done is take an angle grinder to
one of the Allen keys.
I put it in the drill and then I'll just
work it in and out.
Nice and easy.
[Applause]
get a nice result like that. And then
with the pen, it's going to be a little
snug, but slides in perfectly. But this
allows me to pull it out if I need to
adjust where it is later.
[Applause]
I still have these limbs curing over
here. So, I'm going to go ahead and show
you how to do the pins.
It's very much the same process, but the
one big difference is that the bolt
where the threaded insert goes is going
to be a different size. So, this is
where it's important to get the center
because if this is caddyywampus at all,
you will have offc center limbs. So, I
like to start with the template and get
it as lined up as possible with my eyes.
But that's not it. I'll always double
check with calipers just to make sure
something's not way off. So, it should
be the same from either side of the limb
and make sure your mark's the same on
both sides. And that'll make sure it's
not off. The main reason I say to make
some type of template is I find that
it's easier to get right. Since you're
doing this on the limbs and on the
riser, you're marking in four locations.
And if you're using measurements four
times, the possibility that it's
slightly off is greater. But if you have
two holes, even if your holes are not
the exact locations that I said, they're
going to be the same to each other so
that the limbs will fit. Here's another
template. And you can see I hot glued a
second piece on right there. And so with
this template, I can drop it in and it's
a hard stop. Mark your holes. It take
about 3 minutes to make a template and
uh probably save you an hour of headache
later. Here are the measurements. I will
say the limb bolt you can go up in a
size. It doesn't need to be that tight.
Having just a slight bit of wiggle room
in the limb is okay cuz the pin is going
to keep it in line left to right. But
what I'll do a lot of times is use the
2164 and then use a reamer to just
expand the hole slightly and then put
the bolt in. Or you can just go one size
up and drill bit. Now the one on the
inside going towards your limb is for
the pin. And we do not want to go all
the way through the limb.
Now, no matter how you're drilling this,
I will go until my point of the drill
bit comes through the other end. I'll
stop and flip it around. That way, we
don't have tear out.
So, I haven't tested this yet, but if we
did it properly,
which I'm pretty confident we did, this
Where's the pin at? There we go. The pin
should drop in.
Then you have the limb bolt,
which should go right in.
And then when you sight down it, it
should look dead in line, which it does.
So you repeat that on the other side.
Lastly, since I originally started
filming those, I started using these
depth stops here on the drill press
even, so I never have to set a depth
stop. And I find that even better than
that tape method. Just wanted to show
you a cool tool that I've been liking.
Limb bolts are on and everything. And I
actually just filmed an entire section
and scrapped it because I wanted to show
you what you're probably or potentially
going to run into. So, I purposefully
created a problem. So, now that our limb
bolts are in, what we want to do is see
how straight our limbs are. And lots of
times I'll grab a string
chalk line here, but using it just as a
string. And you can go from center to
center. And it's very obvious that this
limb is like half an inch further that
way than it needs to be. Don't know if
you can pick that up through the camera,
but this needs to be shifted this way.
You want the string to be right in the
middle of the bow. And this is a problem
I encountered all the time when I
started doing three-piece bows. So, let
me show you how to fix it. It's actually
a pretty easy fix. And it also doesn't
hurt the bow at all. So that's why I
wanted this pin easy to pull out. Boom.
What we need to do is change the
location of the pinhole. And by change
the location, I mean move the hole
1/16th of an inch to the right. I've got
a cut off from the riser. We'll do this
with
reason we can do this is because it's a
locator pin. It's not structural. So we
just need to move it so that the limbs
locate every single time and are
straight. Additionally, I'm going to put
felt to cover up where the old hole is.
I do a piece like this. It has a nice
taper and it is kind of cone shaped,
just a dowel, but that'll allow a really
tight fit. You could drop it in with
wood glue, but for a quicker turnaround
time, I'll use some CA glue and
accelerator.
So, CA glue into the hole, and then I'll
put accelerator on this piece. Now, if
you want to be particular, you can line
up the grain the same way so it'll blend
in even better.
See, I sanded the top flat. And there we
go. That's it. Now, that accelerator
takes 10 seconds to set up.
And by using a piece of this same riser,
one of the cut offs, you can hardly see
it's there. Now, I know I need to move
it to the right slightly. So, something
shifted. I didn't get it lined up
properly. Use a little scratch all to
pin exactly the spot I want. The
interesting thing is you're going to be
cutting out most of this dowel, but just
a slight bit off to the side.
Now, if you take a close look at this,
you can see the tiny little bit of dowel
that's still in there. But now this
should adjust the limb to be straight.
In less than 10 minutes, we fixed that.
And that used to be like the biggest
stressor with three-piece takedowns is
not getting this perfectly aligned. Now,
there's something you could potentially
run into depending on how you shape your
riser. And that is that there's a gap
between the riser and the limb. And
that's because they're interfering with
each other. So, what I do is I round
over the limb or the riser. You can do
either one to make them fit. It's
generally just on that corner that can
make this problem, but your alignment
can look off if this is off. So, double
check that. Round it over on a sander if
you need to. Now, from this point, I'll
mark the center of each limb. Then, I'll
measure 1/4 in on either side cuz we're
doing a continuous taper from a/2 in all
the way down to 1 and 1/2 in at the
handle. After you sand off or cut off
the excess, you have a really straight
bow that is nice, perfectly,
continuously tapered. There is however a
couple nuances to this. With this bow
build, we glued the limbs up square like
um full size rather than pre-tapered.
You see this one here is pre-tapered.
The nice thing of leaving them wide is
even if your alignment is just like
slightly off, you might have enough
width to still get a straight limb and
you'll just cut a little bit less off of
one taper than the other. If you did a
pre-taper like this, so it's tapered
before you've done hardware, then it
needs to be even more precise. To taper
the limbs, a band saw works really
quickly and really nicely. Doing it on a
belt sander might even be safer. It'll
take longer, but less chance of you
messing up. The key with a taper is that
you take extra time to make your marks
on the back of the bow. And then when
you're cutting it or sanding it out, you
know whether you're going to your line
or beyond your line. You see, if this is
my bow limb and I'm marking my taper
out, what some people don't realize is
that a Sharpie line's about 1/10th of an
inch. So that means 2/10 of an inch or
1/5 when you multiply that by two. So if
you marked with a Sharpie and you
haven't decided where you've marked, you
could be 2/10 of an inch off by removing
material. Cuz if you remove material up
to the line, it's going to be different
than if you remove the line. So, just
plan ahead when you're marking out your
bow, whether you're going to the line or
cutting through the line. I used to do
trim carpentry and different people did
it different ways. I think the cleanest
look is to be able to set it up so you
remove the line. I think that's visually
I think visually that's easier and then
you don't have any marks left on your
piece after the fact. If you mark it out
with a pen or pencil, it's going to be
much smaller of a line, but you can
still be nearly up to a tenth of an inch
off without knowing how you're cutting
it out. So, once it's tapered, it should
look something like this. The limbs are
tapered, they're on the riser, and
everything is looking clean and true.
If you would like to sand this flat, you
can add any type of material you would
like to build a tip overlay up, but
that's not necessary. Rather, this is
how I'm going to do it.
Measure a/2 in down like so. Flip it to
the other side and measure 1 and 1/4 in
down.
Then connect your two dots. And that's
the line we're going to put our string
groove in. Now that everything's
connected,
got a chainsaw file here. I've I'll
filed in about 3/4 the depth of the
chainsaw file, which will equal the
depth of a bow string so that it's
flush. But that's not it for this side.
I want to take out this section. That
way, when we draw the bow back, the
string has somewhere to go.
Okay, now the string can freely move.
Flip it around and repeat on this side.
Okay, both sides are filed in. So, it's
functional now. Now we just clean it up
and the rest is looks. With this style,
I have two principles. One is no sharp
edges. So little pieces of sandpaper
like this to file the string grooves
will be great. The second principle is
don't cut all the way through the bamboo
on the back. Besides that, feel free to
style it however you like. Now, if
you're going the tip overlay route, the
biggest key is that these surfaces are
flat when you glue it together. So, I'll
rub the limb on a belt sander onto the
bamboo. And then I'll grab whatever
material I want. Make sure that's flat.
And then just use wood glue to clamp
these down. Once your tip overlay's
block is on, you can shape it just like
the other method. The main difference
though is that you can cut into the tip
overlay quite a bit. So, I'll cut into
the back of it the same depth as I did
the side so that the bow string is
inlaid into the limb. The creative
freedom is endless with tip overlays.
See, this one here is an old one I did,
but this is a type of horn, and I
thought it would look good to make a
real pointy. It's fairly common practice
to have the bottom one more round and
the top one more pointy. And for uh
traditional old self bows, that was so
that you know which ways up and down.
But here, that's obvious because you've
got an arrow rest and you're probably
going to write your poundage and things
like that and sign it with your makaker
mark. But on a single piece bow like
this with the handle being uniform,
you're like, "Oh boy, does it go this
way? Does it go this way? Check the tip
overlay. Oh, that's square. That's the
bottom. The top's pointy. Feel free to
take 10 minutes on the tip overlays or
go nuts and just, I don't know, do
something out of the box. It is less
about the functional functionality and
more about looks, especially with a
bamboo backing. With that said,
technically more mass will slow down the
limbs, but it's very, very, very small
amount with the amount of tip overlays
we put on. If you were to do a lot,
something larger, something wild, could
slow down the limbs. But what I'm
getting at is uh don't worry about the
functionality with this bow as far as
the tip overlays go. Make something that
you would enjoy looking at or that fits
your building needs right now. But if
you do something unique like this, every
time you look at it in the future,
you're like, "Yeah, I'm glad I spent the
time on that. That's that's a nice
touch." Hey, here are some tools I
recommend for this. If you like carving
and have a a Dremel tool, something like
one of these. Here are some bits that
are the most useful. A bit like this can
replace your chainsaw file. A sander
like this can replace your rasp. And a
flap wheel and a burnisher can replace
sandpaper to a degree. And then finally,
this roll of sandpaper is great. This
sandpaper is really cheap. And the nice
thing about it is you can roll it out,
rip it if you're strong.
Goodness gracious, that was harder to
rip than I thought. But here, here it
is. So you can rip a small piece here.
See small sliver and it rips down
vertically. So now you can grab this and
file or um you know create your own
little inside the grooves. So this
sandpaper is great. So those are the
tools that I recommend. If you're doing
it by hand, a fine tooth rasp or file, a
chainsaw file, and some sandpaper and a
sandpaper roll. Here's some different
tip overlays. This one's a bamboo with
clear fiberglass. This one's an Osage
one. This one has Osage and fiberglass,
walnut fiberglass.
That one's a mix of something. This
one's unique and different. And this
one's as plain as you can get cuz the
red from the sealing the end is still
there. This one's a senue wrap because
of the senue on it. And it comes to a
fine fine point.
Also, there's more variations up there.
In the end, it's what makes it so fun is
because even if you're making the same
style of bow as somebody else, it is
yours. It's you're building it. It's
customized to you. And it it makes it so
cool. And the moment you shoot it for
the first time is a experience that is
one of the highest moments I've
experienced, especially when it doesn't
break and it shoots great and then you
practice with it and you're like, "This
thing's awesome." I have tried every
possible tillering method and I came up
with one and today I'm revealing to you
what I call the magical tillering
method. I wrote all about it in my book
and it's underwhelming because it's so
easy to get a really good shooting bow.
If you want to struggle in tillering, do
it all by eye. Try to visualize what it
should look like and then just slowly
tweak it for a couple of days and you
can get a great bow. But if you want
guaranteed success, this is how to do
it. My original idea around this method
was how can we make this as easy as
possible. And what I found out through
some extensive testing is that where the
bow rests with a string on it is the
same how it bends with it pulled back
with this design. What that means is we
can do all the tillering right here at
rest and we don't have to draw it. Now,
once you remove wood, you must exercise
the limbs to give it a new memory. Wood
has a memory to it. And so, if you just
remove wood, nothing's going to change.
That's why you want to pull it back 25
times or draw it on a tillering tree or
tillering stick. But once it's
exercised, you can retake your
measurements. I've done this with
multiple multiple bows and found that if
you're precise with those measurements
and you have your positive tiller at its
brace height, it's going to shoot good.
Now, with this style, it'll be like a 67
or 68 inch bow string with this design.
Here's the one that I've completely
finished already. It has a half inch
limb thickness in the center of the
limb, and that is a 48lb bow. Just as a
rough rule, keep it above a/ in if you
want more than 50 lb, below/ in for
less. But tillering is going to be a
little different here. I'm going to
tiller by using some measurements. Okay,
so here's the setup. I'm going to go
every 5 in, and I'm going to put it in
the same saw. So 5 in and then we'll go
out to 10. We'll go out to 15 and we'll
go out to 20. Then we'll repeat that on
the other limb. From here I'm going to
measure on the 5 in mark. Now you want
to be on the exact spot. So I put the
left end of the tape measure on the
inside and then I'll go to the inside of
this mark as well so that you're in the
same spot. But here I've got and you
want to be precise five and 9/16.
And here I've got on the inside 5 and
716.
Okay. So that right there at the 5 inch
mark is telling me I have a negative
tiller. I'll continue on with each mark.
And what I'm looking for is that the
marks are the same all the way along.
Once I get it the same all the way
along, I'll adjust the upper limb only.
If it's the same at the five, but it's
not the same at the 20, the stiffer limb
just needs material removed near that
20-in mark. As you may know, my tool of
choice is my cabinet scraper. Low
quality one that I've had for 12 years,
but you can just sharpen, resharpen it
forever.
The one thing to pay attention to is the
left and right side of your limb to make
sure you're removing material evenly.
So, the most precise way is calipers
47.45.
That's pretty close. But what I can do
is just tilt this slightly
to knock down the more of the side with
47 and keep those even. It's not too
difficult to get 110 or 20 thou off and
then you can start having some limb
twist problems.
And if you don't have calipers, you can
use a tape measure. But I will say I
found this one on Amazon. It's like $4
and it's good enough to measure this
stuff. It doesn't have the nice features
of the metal ones where you can lock it
in place, all that. But just to check
stuff and just have a I bought four of
them so I can just have them everywhere
and I always have them on hand. I found
that to be useful. And then I keep my
nice pair for when I'm doing super
precision stuff.
My limb was bending evenly throughout.
It was just needing more off this limb.
So I'm doing full passes
and you end up with these good guys.
20 passes later, let's test it again. I
built out this tillering tree, but you
can also do it with a tillering stick.
This is a 2x4 with some screws screwed
in. And you do the same thing. I
actually really enjoy using
screw it right into the workbench. And
then you can put your bow up here. And
then when you pull it along the screws,
it stays in place. This is looking good.
It's not supposed to be an even bend
like a like a normal self bow. I guess
because of the reflex, it's not going to
visually look like a typical bend.
That's where the math really helps
because it'll look like it's bending
less in the middle where we reflexed it
the most. And that's okay. I think that
helps with the speed to fling the tips
forward further and sooner. So, the
thickness of the limbs as well as this
distance is going to matter more for
you. Before you retake your
measurements, you want to exercise the
limbs, which is just going to be drawing
it. You can do it like that. You can
grab it and pull it. You can also put it
over here and draw it down. I fully
expect some people who will build this
will probably have a setup like this,
get it dialed in using their calipers,
checking everything, spend two days on
the tillering to get it perfect, where
there's going to be other people who
take this to a belt sander and do the
entire tillering on the belt sander and
call it good. Not one way is better than
the other. I do both depending on the
bow I'm making and depending on my goals
for the bow, but I'd like to present you
many different options so that you can
make it your own. But because we kept
the limbs pretty even the entire way and
because of the 8 in fade out, we have a
natural tiller in the bow already.
Mostly we just need to remove wood on
the outside. Okay, so 45 lbs at like 21
in. I want to remove some more material,
but it's looking really good.
Okay, sweet. 2 minutes of removing wood
gave me slightly positive tiller
actually.
We've got some good news. It's tered
really nicely. So, here's a sneak peek
shot. The handle's still terrible as far
as not being finished out yet. So, we'll
do that. But I like to shoot it as soon
as I can
it.
To finish out the handle, I'm going to
round the shelf so the arrow only
touches in one spot. I'm also going to
round this a little bit more. Smooth
everything out. Get it feeling proper in
my hand. Proper is personal opinion, but
is how I like it at least. We'll do
final sanding. The back of the bamboo.
You can lightly sand that to make it
smooth and look how you would like it
to. I'm going to round over the corners
gently and sand everything down. Then
I'll do makaker mark spray finish. Now
that you have the positive tiller, the
final step is to shoot your bow.
And if it shoots smooth and it checks
out and you like it, you're done. If
not, double check your measurements,
exercise the limbs, and retailer it as
needed. Okay, for finishing the bow, I'm
not going to go super deep here. uh
YouTube Kramer ammons finishing a bow or
refinishing a bow and you will see some
videos uh dedicated just to finishing.
But the simplest thing to do is just to
get a spray-on polyurethon. Just get a
can of this stuff and spray the boat.
That's the simplest way. The idea is you
want to use finishes that are good on
high contact. You want to use something
that's waterproof and it's basically any
other type of wood finish. Uh
additionally, you can write on the bow
what you want. I often will write the
draw weight. I'll do it at the draw
length. So, this one is 48 lbs at 28 in.
Um, and then I do my signature. You can
also put on the ammo if you want, which
is for a long bow going to be 3 in
longer than the string. So, technically
this would have a 71 JMO with a 68 in
bow string. Now, in the next video,
we're going to shoot this thing, but I
do want to say a big thank you to
everyone who's picked up my book so far.
And if you're building this bow, thank
you so much. A fivestar review on this
book would mean a lot to me if it's
adding the value that you expected. All
right, I'll see you guys on the range.
You don't need this book to build this
book. Yes, you do.
You don't need this book to build. You
need the book, though. And
you don't need You need the book. But
you just Yes, you do. You just need to
watch All you need is the book. So you
just need to watch this
