How to make a Viking Age Lenticular Round Shield woodworking and metalworking Tutorial

Shielded Dynasty Network
2 followers
6 Video Views·Jun 27, 2025
Hello YouTube and welcome to Tale of Steel Armory. Today I'm going to teach you how I made this
a lenticular round shield. So as the base material for my shield I used some six millimeter
plywood pebbler which I got from my local hardware store. I cut it into six millimeter
wedge strips on this really nice little table saw making sure not to cut off my fingers
because you know there's some safety features that are missing on this on this machine on this
particular one. Also off camera I already built this little jig made from some leftover plywood.
As you can see it consists of a row of semi-circles and has a diameter of about 70 centimeters.
I started by just bending the material over
and screwing it in place on both sides just to check if the jig would work. Yeah as I intended
just to realize that yeah it didn't. So I had to sand off a lot of material from the jig with this
little belt sander which I borrowed from my father just so this the radius of the pieces
when I bent them would contact all of these little ribs which was quite tricky. But after
all that sanding it would contact at least I think four or five of the seven ribs which was good
enough for me. So I just screwed on the second piece right next to the middle one and as you
can see there is a little overlap which has to be taken off. At this moment I really didn't know
how much or what I just eyeballed it but I got quite sophisticated at it later. I'm gonna
explain to you how I did this in a few seconds. On these pieces I just yeah went on it with my
belt grinder, checked if it fit and went on it again if it didn't. I think I took off about four
millimeters from both sides so eight millimeters on one side which yeah wasn't the right way but
I kept the pieces on because it worked and just wasn't a problem. Yeah and after the first one
was made to fit I translated it over to the second one just used it as a pattern and that
was the first three of the boards. Yeah I did the same for the fourth and fifth board and noticed
that I had taken off way too much material and that my method isn't really going to be practical
in the long term. So I just sat down and thought about how I could make this possible. I started
by clamping down the piece on both sides with some screw clamps and as you can see there's a
little gap that forms when the pieces are laying in the right position. I measured how far this
gap would be and translated it over to the sides. Then I went over to the workbench. I used these
holdfasts as an anchor point and another piece of material as a ruler. I tried aligning the edges
so that they would be the starting point of the radius and bend the ruler to the edge so
this would give me a really nice radius which I then cut out with the jigsaw
and used the bed grinder again to clean up the edges.
And as you can see with this method the pieces fit quite perfectly. I later started to send
them down at an angle so they would leave even less of a gap but yeah there's always room for
improvement. And after a few more pieces I started to run into another problem. As you can see I'm
running out of material and the cutoff pieces which I had left over which I actually planned
to use as the side pieces on the shield they were just a bit too short so I had to cut off
some more material. I expected this so I just bought a second board but I should have planned
out my my cuts a bit better because I wasted a lot of material. And yeah with the two pieces
I fucked up that was way more than I expected. Now since I wanted the shield to be thinner on
the edges and a bit thicker in the middle I just took off some of the screws and yeah tried to thin
it out first with a hand plane an electrical one which yeah was semi-optimal and yeah later
with the bed grinder which took a lot of time and yeah this whole thing really didn't work as I
planned it. It was a lot of work I've been sanding about an hour on the piece and only managed to
thin it out on the edges and not really yeah it wasn't the result I wanted which resulted in the
shield being way too heavy now. But since it's only a display piece and I'm not fighting with it
it's okay. It's sad but it's okay. Here you can see my end result it's getting quite thin on the edges but
not really thinned out anywhere else. Yeah at this point I just decided to leave it as is and
take off a bit more on the the next layer which I did but as I said the shield is way too heavy now.
Just a little side note the whole construction process only on the shield body
without the jig without covering it without all the metal work took over 12 hours of work
just me making little planks screwing them on screwing them back off taking something off
screwing them back on making another row sanding it down a lot of repetitive work so I just left
it out of this cut. You know the drill. And here's some information from my editing room
I forgot to plug in my microphone. I've been recording about half an hour right now and
well I just looked down and saw that there was a plug missing and yeah I've been recording with
my little webcam microphone for the whole time which unexpectedly doesn't sound that bad.
So I'm just gonna keep on recording with it because well why not.
Another miscalculation on my part was that I ordered a full bucket of glue five liters
which was not cheap about 20 28 euros I think and well I only used about a liter of it
maximum and as you can see I took off each plank individually tried to cover it with
as much glue as possible with this little paintbrush I stole from my last employer
and yeah I just went over the whole thing taking off each plank covering it screwing it back on
marking it with a pencil so I didn't so I wouldn't screw it off back again because
I wasn't really working with a system here and after I was finished with that I just left it
to dry over the weekend and started with the metalworking. I've decided to use the traditional
cold forge this time so I had to split some kindling some firewood to light it up. I cheated
a little bit because I used a modern barbecue lighter to light up my firewood stack. I let it
burn down a little before I started stacking up some coke around it which gave me a nice little
forging fire. For the base material I used some two millimeter sheet metal just some basic mild steel
and I cut it out with my Makita electrical shears which was as you can see a bit tricky because you
have to bend the material out of the way to cut it and with this thick of a material it takes quite
a lot of force to do it. Not from the shear, the shear works perfectly just to bend the material
out of the way. I started by dishing the material with a two kilo rawhide mallet into this little
dishing form I made a few years ago. It's quite handy. I made sure to only dish it shallow and
do the rest in the hot form because I didn't want the material to rip.
You could dish it out way more but this is gonna thin the material down so the end result is gonna
be weaker which I didn't want. Also I wanted to test out a new technique. That new technique I
wanted to try out was raising. It's a classical blacksmithing technique which was used way back in
high medieval times to raise out helmets and such and sheet metal pieces in general
without thinning down the material which is quite tricky as I might add.
I really didn't know a lot about the technique and I still don't but I've tried it at least.
The end result was quite okay. The basic idea is you heat up one section at a time and try to
push it inwards on your little anvil. You're hitting it a bit off center so you're not
squishing the material in between the anvil and the hammer, thinning it out that way. Then you
work yourself around one section at a time until you reach the bottom where you try to squish the
folds to make it flat again. You only do a few centimeters at a time to control it better.
You work yourself around a few times until you have the shape you want.
Keeping the thickness as it was before or hopefully keeping it. It's really a lot harder
than it looks and I really didn't know what I was doing at the time. It more or less worked.
I'm not really pleased with the end result. I did end up thinning it out a bit and it didn't reach
the depth I actually wanted but still the shape wouldn't be possible just by dishing so
I can't complain. It was the first try after all. Another quick note from the editing room.
Editing these videos is no fun. I really hate it. It takes hours and I don't see
any progress in it. I've already finished my project and now I have to do all of this
just to make a little video out of this. The reason I do it or what keeps me motivated is
that I've seen my last video has really gone through the roof much more than I expected
actually and this really boosts my motivation. So please if you want to support me and see
more of these videos just leave a like or subscribe and just leave a little comment
what you would do better how you've solved these problems if you've made one of these
or just tell me something nice. I don't know.
That's just what I wanted to say. Thanks for watching.
After raising it out to a sizable depth I started to stretch out and flatten the rim
with the flat side of my hammer over the rounded off corner of my anvil
carefully working myself around. Then I realized that I did not work out the piece deep enough
so I still had to do some dishing. I started by pushing out the inside to achieve that step I
wanted. I then proceeded to work the newly created edge of the boss on the horn of my anvil just to
push it out a bit more which worked fine I just had to do some light taps and be really careful
not to destroy it. After that I also really carefully dished out the midsection a bit more.
This is where I failed with the last piece which got so stretched out in the middle
that it formed a crack which destroyed the piece and I lost about one and a half hours of forging.
Once I was pleased with the rough shape I put it into the fire one last time
trying to heat it up evenly and letting cool down slowly to take away some of the build-up
stress and tension in the material. Once it's been cooled down to about 300 degrees
I started the planishing process. Planishing is another old-school
anvil making technique where you try to flatten the surface by repeatedly hitting it with light
blows over an anvil which is roughly the shape of your workpiece. Since I did not possess a
shield boss shaped anvil I switched from surface to surface working the inside with a round hammer
on a flat surface and the outside with a flat hammer on a round surface. This also cold hardens
the material a bit and makes it more brittle. You can also sand the surface with a sanding block or
with a file to make the deep and high spots more visible. And after an hour of planishing, sanding,
filing and grinding I ended up with this. To make the rivets I cut off some 6mm round bar
and heated it up in the gas forge. Once they were nice and hot I just took them over to the anvil
and squished their heads with a ball-beam hammer. This normally took only two minutes.
I finished them off on this piece of steel with a hole in it then I also made some nails which
I didn't end up using. Next I cut out the handle section out of a 3mm piece of sheet metal.
I just hammered both ends into a taper to tip them to a round disc. Then I spread out the
mid section of the handle to about a millimeter where I would later insert a piece of wood for
the handle. I also ground down an old bolt on my bed grinder because I didn't have a lathe.
I rotated it in a power drill and yeah started first by grinding and then filing it down to
the shape I wanted and I sawed it off with a hacksaw. Then I drilled a hole into the center
of the boss and drilled it on the lateral nub with a round-faced hammer. I also drilled six
holes around the rim of the boss to later rivet it onto the shield. And three into the handpiece.
The fourth one is gonna follow later because it has to fit to the boss. And with that I finished
the metalworking section of this video. Now back at the woodworking station I marked a circle
around the middle and around the rim of the shield and cut it out with a jigsaw.
The outside diameter ended up to be 68 centimeters the inside about 13.5.
I also again tried to thin down the material
with the belt grinder. This again didn't really work so well and the shield was still way too
heavy. After that I covered the whole thing in a thick layer of glue and started to stretch a
sheet of linen over it. Of course I used way too much glue so I had to spend the next hour just
popping and cleaning the little glue bubbles that got pushed out of the cloth.
Then I gave the whole thing a day to dry out and cut off the excess.
I tried to mix up a nice tone of red because I just couldn't find any in my local hardware store
and I started painting it with two layers of this mixed up red color as the base and then
tried to add some yellow stripes to it. Of course this was done. The red always started to shine
through after I dried so I had to cover it with about six to eight layers of the yellow color
which was way too much work again. Now back to the forge I drilled the holes for the rivets
and also made some washers out of leftover pieces of one millimeter sheet metal.
Just punching a hole and cutting them out with my metal shears and then I just riveted on the boss.
For the handle piece I cut off a bit of 28 millimeter pine dowel which I actually wanted
to use for my spear but it was a bit too long so I could sacrifice a few centimeters. Don't
forget to check out that video right after this one. I'm gonna link it down in the description.
It's really nice. I shaped a little piece of wood on my background and fitted it on
and now all that was left was just drilling a few hundred holes around the outside to stitch
on the rawhide rim. I bought two rows of rawhide on ebay for way too much money again
and let them soak in water for a few hours to make them a bit softer. Then I just had to punch
double amount of holes into the rawhide with this little hole punch I use for leather and
quickly sew it on before it becomes too stiff to work with. And now with this last step done
I went back to the forge and drilled out the rivets for the handle again. The problem was
with the handle facing into the boss there wasn't enough room for my hand which was quite
uncomfortable. So I just turned it around made some new rivets with a little riveting jig I
made extra for that and riveted it back on. And now after about 40 hours of work and really a lot
of mistakes which could have been avoided the shield was finally finished. I'm not really
pleased with the end result even though it looks really quite good and it fits my kit quite nicely
it's still really heavy and a bit uncomfortable to hold. If you're now feeling inspired to make
your own lenticular rod shield don't make the same mistakes that I did and don't forget to let
me know how it went in the comments. And if you got that far in the video and liked what I'm doing
don't forget to check out my channel especially my Gondor Fountain Guard Helmet series was really a
passion project for me. Stay patient and don't let some little setbacks stop you. Thanks for watching
and see you in the next one!
