Liquid Transition - After Effects Workflow & Tutorial

Motion graphics
5 followers
3 Video Views·Jun 23, 2025
This video details the workflow for creating a liquid transition animation. The creator walks through the process of animating a can transforming into a beer pour, using rough animation software and then cleaning up the animation in After Effects. The video also covers adding shading and highlights to the animation.
I'm going to show you my workflow for this project and break down the liquid transition.
Let's begin.
Youngbloods, a brewery in Australia approached me to make a short animation for their beer
going to tap, with a can transforming into a beer pouring.
I made some style frames first using elements that I'd drawn in Illustrator,
imported them into Photoshop and added some shading with this grain brush that I've made.
I did a rough pass of the cell animation in Rough Animator,
but you can use any frame-by-frame software.
I started off with a frame of the can and decided I would try swirling from the bottom left,
whipping up and around and then slamming back down where the next designs would be revealed.
This would be my guide layer.
I started drawing a few frames straight ahead,
creating a new frame and loosely drawing where I think the motion should be.
About halfway through the transition, I had this elongated blob shape
and I knew that it would be smooth sailing for the back of this transition.
Because I've done a lot of animation with simple blob shapes,
I knew that I just had to draw blobs following this path up and around.
More drawings at the top so it slows down and then have them getting further apart
and stretching so they accelerate towards this sort of explosion at the end.
I jumped ahead and completed that sort of last section of the transition,
but I still missed a whole bunch of animation
going from where the can started to warp until this blob.
So I needed to figure out how to fill those in between shapes
because it's a pretty drastic cut here and I knew that this would be the trickiest part.
And here it's a bit of trial and error.
I created a new frame in between these frames
and tried to imagine how this can would be turning into the liquid.
Knowing it was going to look like this blob shape in a handful of frames.
Because this was going to be a pretty fast motion,
I only needed about three frames that were in this tricky state of warping can.
The first one I pushed out these existing warps to their extremes
and started to round out the top of the can.
On this next frame, I rounded out the left side of the can
because these sort of tendrils that were sticking out
would kind of be folded and wrapped behind that view anyway
and that'll help us get us to this round shape going to arrive at shortly.
And on the right, I pushed it further to the left
and had the back of the can start to become visible.
Now I was only left with one frame.
And looking at my onion skins,
which is the faded view of the previous and next frames,
I drew in between the edges of where these shapes were going to be.
This is where the animation was going to be at its fastest.
So as long as it kind of made sense, we were going to be okay.
And here's what it looks like all together.
To make those little blobs that trail the main shape,
I made a new layer and drew a blob where it might separate from the main form.
Like here when it makes a turn.
And then on a next frame,
make that blob going the same sort of distance following this main shape.
Again, one more going that same shape and then slowing down,
just going a bit further away and the shape getting shorter.
And then I repeated that a few more times until that I felt that there was enough,
making sure they don't all start and stop at the same time.
Now I worked on that for a little bit longer,
sort of tweaking and refining these shapes.
And then I added some more explosion effects at the end.
And here's what that final rough looked like.
I then exported that just as a movie file and imported that into After Effects.
To clean up these roughs, I used shape layers in After Effects.
For the main can shape, I imported our can from Illustrator,
added some extra points with the pen tool,
and then every two frames moved it to match the roughs.
Once I got to this blob part, I made a new shape,
so it would be easier working with less points.
So here's what those cleaned up shape layers look like.
To add the shading, I'm first going to color them black,
and I'm going to create a new shape layer with my pen tool
and draw a shape that goes around the edge of our can here.
Let's drag that on top of our can main layer.
I want to change its color to orange and rename it can main shading gray.
And I need to add a few effects.
First, let's add set matte.
And we want it to take the matte from layer 28, our can main front.
So now it's only visible on that can layer.
And now let's add roughened edges.
Let's put that above this set matte in the layer stack.
And to scale down to 10 and the border maybe up to 100.
And now we've got this nice sort of grainy look here.
I'm going to keyframe its path property.
And then using the keyframes that we made on this main shape as a guide
and every new frame, I'm going to adjust its position slightly.
That's one side of the can done.
To do the highlights, I'm going to duplicate this layer here,
rename it shading red.
I'm going to change its color.
I'm going to make the border a little smaller, about 75.
Get rid of all of these keyframes,
and then just nudge the path over a bit more to the left.
So we now have a nice little sort of hit of red on the edge here.
And then I'm just going to keyframe that path property again,
just keeping it to the very edge of this can.
And now I've got the shading on the left of this can.
And then I did that for every layer.
Now that may seem like a lot of work and it's certainly not super quick,
but it only took a few hours and I think it was worth it.
I animated the logo in Photoshop on top of a guide layer
of those main layers that I'd rendered out.
I did this in Photoshop so I could edit the logo easily
by lassoing a selection, going up to edit, warp,
and making adjustments that way.
I imported that into After Effects,
added the looping texture onto everything,
and this was the final result.
I've made a short playlist of some related videos
that I think you'll enjoy if you've made it this far.
I'll see you in the next video and please consider subscribing
if you'd like more of these videos every week.
