Helmets: The Armet

Shield of Antiquity
8 followers
Jun 22, 2025
Today we take a look at my second favorite helmet, the armet; from its early form in the beginning of the 15th century to the most typical late 15th century styling.
Comments are disabled for this video.
Hello everybody, welcome back. I'm Ian LaSpina and in today's video we are going to be discussing
armets and this example of a reproduction of the Sherbert number S18 armet. So around the same time
that the great bassinet was taking off in popularity, in Italy they were experimenting
with ways to make the helmet more close fitting to the actual human form. If you think about the way
the bassinet tends to go on, you put it over the top of your head and slide it down into place.
So the bottom opening can never be smaller in circumference than the largest part of your head
which tends to be the brow. But if you think about the way your head is shaped, below the brow your
head tends to get narrower down to the jaw and then below the chin it gets even narrower around
your neck. So in order to get a helmet to fit closely it requires some sort of hinged or moving
component. There were a couple different ways to approach this problem and I find it difficult to
talk about the beginning of armet design without also addressing another family of helmets that
took a similar but slightly different approach to this problem and that is the Venetian great
bassinets. So this is kind of an interesting family of helmets. There are several survivals
and what you're going to see is on the... this is what they look like. So this is an example of a
Venetian great bassinet. It has a side pivoting visor. The top of the skull is very similarly
shaped to contemporary bassinets but the most notable design difference is this big hinge on
what would be the wearer's right side. It's composed of a lot more plates than a normal
bassinet of the time but what this hinge does is it allows that that cheek plate to swing open so
that you can get your head into the helmet and then secure it in place. You'll see down on the
center of the neck there is a locking pin mechanism to keep the the cheek in place.
If you look at it from the front you'll also see that there's only a hinge on what would be the
wearer's right side. Remember in previous videos when we talked about asymmetry in armor when it
usually manifests itself on the right side being the more compromised side and the left side being
the more well-defended side because of the side on which you're more likely to take a blow especially
a lance shot. You'll also notice here's another example unfortunately the hinged cheek plate does
not survive on this but the visor is similar except this one only has a single sight so the
sight goes all the way across instead of two individual sights like the previous one we looked
at. Here's another example with a much wider facial opening and again hinged on the right
side of the cheek plate. It actually starts to be reminiscent of the later form of the barboot.
There are also several visors that are listed as bassinet visors that survive that have a very
similar design to what we see on the Venetian great bassinets. Here are a few examples and
you'll see that they're all very similar in their basic appearance. Again some have a single sight
across some have a double sight but they're all relatively shallow visors pointed a little bit
towards what would be like the bridge or the nose to kind of close that gap formed by the
the shape of the helmet so that once the cheek piece is in place the visor is down it's actually
very enclosed but fits better to the narrower parts of the head than say earlier bassinet styles.
So now taking a look at what would be considered the first true armets and what I'm going to use
is like the working definition of armet here is a close-fitted helmet shaped to the head
that has hinged cheek pieces on either side so that the entire lower part of the face opens to
permit getting the helmet on and off but when it's closed provides a very close fit to the wearer's
head. The first time that we really see it in art is around 1410 with the publication of Fiore di Liberi's
Fior di Battaglia manuscript. It's a fighting treatise put out by an Italian fencing
master around 1410 but in the armored combat sections we see a lot of what look like early
armet designs. So these are examples from the Getty version of the manuscript and you can see
that the guy on the left with the long sword is wearing a very close-fitting helmet with plates
that form underneath his neck and chin to fit closely to the head. Here's another example of
an early armet being worn on horseback with a visor. You'll note that the visor is similar
in design to what we saw on the Venetian grand bassinets. Here is an example of two armets.
The guy on the left is wearing one without a visor. The guy on the right has the visor down but
what makes them characteristic of armets is that tight close fit under the chin as the plates form
to the jaw and the neck. And then finally here you see this guy's caving in his buddy's face
with a poleaxe and he is wearing a very typical early armet. What I want you to note here is the
shape of the skull and then the way that the face protection forms kind of a scooped out bowl that
comes from under the chin and up to basically the sight, the top of the sight. So the actual ocular
without a visor in this case is formed by the lower edge of the facial opening and then the
top edge of that bowl that protrudes out into the front. And the reason I'm pointing out that
particular style is because one of the earliest actual survivals of an armet, which used to be
in the Sherberg collection, it was Sherberg number 57, matches that image pretty well if not exactly.
So here is Sherberg number 57. You can see that in profile you get that same scooped bowl
shape of the hinged cheek plates. The side of the helmet you see that kind of bar across the
side of the helmet where the two plates come together that's a flange that's actually protecting
the hinge itself. So if you remember to the Venetian great bassinets the hinge was pretty
much completely exposed on the outside. On the armets the hinge seems to be attached to the
inside of the helmet and then the attachment points at least on the top are typically protected.
The actual hinge mechanism where the pin goes through is protected by this flange.
You'll also notice that there are verveils along the lower edge of the neck here
to attach a very short aventail. From the front and from the back here you can see kind of a
combined image of the different views of this helmet. You can see how on the back of the helmet
the skull and the back of the neck are continuous and then it narrows into a what people usually
call the tail of the armet there and then the cheek pieces as they close around the neck form
the additional protection around the sides of the back of the neck and then ultimately all the
way around to the front. This is an Italian fresco of around the same time dated to between 1410 and
1411 and you'll notice that here in the bottom left there is another person wearing a very
similarly profiled armet. The earliest known example of an armet on an effigy is actually
on a German effigy of 1416 Dietrich Hofer and you can see what gives it away as an armet is the way
that it comes in close around the bottom of the jaw and then you can see the locking mechanism
on the front and center of the throat to actually secure the cheek plates into position.
Another great example of an early surviving armet is the Scherberg number 18 armet which is what we
have an example of here. So taking a look at Scherberg number 18 you can see that the basic
profile of the helmet is very similar in shape to the previous one that we looked at so this one
dates the dating changes over time but it's usually dated to around 1420, 1415, 1430 in that neighborhood
so roughly in the first quarter of the 15th century kind of bleeding into the second quarter
of the 15th century but the the profile is very similar. Notable differences are the side pivots
which would become kind of standard on armets. Side pivots very similar to the way a bassinet
visor is attached. It still has the flange to protect the hinge. It still retains the verveils
around the bottom of the neck for a short avantail but what you're going to notice on this armet is
it has actual breaths so the holes punched into the helmet are present on this. That's not very
common on armets and the big design feature that everybody sees right away is what I call the
picket fence but the teeth that are cut into the top of the cheek plates. So what this does is it
still provides protection all the way up to almost the lined up with that this edge here so
you actually have a very small gap for which weapons can get into the helmet but it still
allows you to kind of see through that. So again like we always say armor is always a trade-off
between protection and some other desirable feature in this case vision. You're able to see a
lot more but this is now weaker than the previous example that we looked at. Can these be bent?
Yes. Can they be broken off? Yes. It's definitely possible but the wearer, the designer of this
helmet decided that at least the experimentation of adding additional vision was worth
that trade-off and the potential loss of protection in this particular spot.
Now with the visor down you're going to end up mitigating that. We'll talk about that more when
we take a look at the actual helmet example that we have here. One aside real quick is
everybody likes to point out like the one thing that you know some some scenario that could
happen that could potentially defeat armor. Remember the point of armor is not to make you
invulnerable. It doesn't exist to turn you into you know you're not supposed to be completely
invulnerable on the battlefield. What it's supposed to do is make you more survivable
in a combat situation. So there will always be some way to defeat the armor otherwise
you're going to end up locking yourself in a steel vault where you can't move and you're
completely combat ineffective. You need to be able to see, you need to be able to breathe, you need
to be able to fight. Ultimately even in today's technology armor is never completely protective
in order to be able to fight there's always going to be some sort of trade-off. This is one of them
so somebody decided that seeing was pretty important and I could agree with them. Now if
you know the moon is in the seventh house Jupiter aligns with Mars and a war hammer happens to hit
right here and bend one of these things in and allow weapon penetration yeah it's going to kill
you but we need to temper that kind of thought process with how likely is that really these
people are moving they're competent at fighting you're not going to present the weaknesses of
your armor to your opponent. Okay so moving on to later and what would become more typical 15th and
later 15th century armet design. This is an example from the met of an armet dated to around 1430 to
1440. You'll notice that the skull is a little bit more rounded over now it's a little bit less
bassinet shaped there's now a medial ridge the medial ridge on the helmet is a lot more pronounced
than it was on previous iterations. It still has a side hinged pivot this particular one still
retains verveils we'll see that later armets end up going away from the verveils it still has the
flange to protect the hinges on the cheek plates but one of the notable differences is this
additional plate on the forehead so armets ended up getting a reinforcement plate attached above
the top edge of the facial opening to reinforce the forehead. You'll also notice that unlike the
number 18 armet later later armets typically do not include breaths in fact I'm not sure of
any that include breaths so what we do see though is the facial opening on the armet when the visor
is up tends to form this kind of t-shape so the visor I'm sorry the facial opening tends to kind
expose the nose too when the visor is up so that would definitely aid in not only vision but more
importantly more importantly breathing. Other notable features of later bassinets
I'm sorry later armets are the inclusion of the rondelle so you can see on the back of this on
the back of the throat of this armet example here the there is a rondelle that is projected
off the back of the helmet on a little post we'll see what kind of role that plays in a little bit
when we talk about wrapper plates but before we get there I want to talk about visors so the visors
on later armets if you look at this one you'll see that the actual visor itself only includes
the lower edge of the sight the part where you look through only the lower edge is actually
attached to the visor the upper edge of the sight is actually formed by the lower part of the brow
plate so when you raise the visor that brow plate is obviously not moving and only the lower half
of your sight is raised. There are two different kinds of visors there are visors that do include
the upper half so here's an example of a first half of the 15th century armet and you'll see
that on this particular example the the visor itself includes both the lower half and upper
half of the sight so it's a little bit more robust of a visor for whatever reason there are images
here is a 1440 to 1450 fresco from Italy that shows a lot of armets and they appear to have
visors like that example where the the visor is the more robust design where it's on both the top
and the bottom but for the second half of the 15th century it seems to have been a lot more typical
for the visor to only be that lower half and then allowed the the rest of the helmet to form the top
half of that sight. The other important feature that really makes the armet very well suited to
cavalry use is the the inclusion of the additional wrapper plate which is an optional feature that
can be added to an armet so if we look at this particular armet here you'll see that there is
a strap that goes around the back now you can see maybe why that rondelle exists but more importantly
here the wrapper plate is an entirely additional plate that fits to the front of the armet and it
includes a reinforcement for the lower half of the face and also usually includes articulated
plates that now extend downward to form a continuous plate protection from basically
the above the mouth down to overlapping the chest so that the throat is considerably more protected
than wearing the armet without the wrapper plate so the drawback is when the wrapper plate is on
the armet itself is going to become less mobile especially from side to side because of the way
that it overlaps with the chest so it's going to hit the chest it's going to bind on the chest as
you move but that's a desirable feature when you're in a cavalry situation you're on horseback
you now have a very well defended throat an extra layer of steel across the lower half of the head
so if you do get struck by a lance it shouldn't be able to snap your head to the side as easily
it provides a smooth glancing surface and double reinforcement on the place where you're likely to
take a lance strike you'll also notice that there is a peg sticking out of the visor that fits neatly
into the wrapper plate that's a lifting peg so that you can still grab the peg and lift up the
visor as necessary because the visor can raise and lower even with the wrapper plate in place
here is another example of a surviving armet with a wrapper the rondelle on this particular one is
a restoration the skull and the wrapper plate are both original but probably not associated
because you'll notice that the gap in the wrapper plate for the lifting peg does not line up with
the hole on the visor for where the lifting peg would have gone but they both share similar
maker's marks so they were probably both made in the same workshop however they probably weren't
intended specifically for each other but that is how they're displayed now and you can see that
that rondelle actually not only forms a place it does protect the straps in the back a little bit
to protect the wrapper plate but it also forms a nice little place for those straps to sit on so
the wrapper plate stays very stable on the on the on the helmet okay so now what we'll do is
take a look at the example that we have here so this is a reproduction of the scherberg number s18
and dated to like we said around 1420 1415 and that kind of first uh first portion of the 15th
century um the original the visor does not survive but we'll come back to that in a minute so uh
taking a look at the features if you look at it from profile you get that characteristic swept
kind of bowl scooped look that we see in early 15th century armets the skull from profile forms
a peak similar to the way that bassinet skulls were shaped at the time this is the border of the
hinged cheek plate here's the flange that protects the hinge mechanism which is just under here on
the inside so here you can see the rivets that attach the hinge to the inside and then the actual
hinge portion with the pin going through it is right underneath the flange
breaths on the right side a small number of breaths on the left side and then the picket
fence in the front here the holes around here are for a sewn in liner this particular helmet at this
present time has modern padding in it so that's why you don't see thread um here right now uh
holding in the liner and then we have reveals around the lower edge to attach a very short
avontail and then looking at the back of the helmet you can see that the skull is continuous
down to the um the base of the back of the neck and then the sides of the neck
wrapping around to the front are formed by the hinged cheek plates
this is the mechanism that you use to open and close the cheek plates so all it requires is a
90 degree turn it unlatches it and then the cheek plates can be hinged independently
and this is what enables you to get the helmet on and off because the
opening in the bottom of the helmet is far too narrow to actually slip over the top of your head
one of the big advantages of the armet is that you get that kind of close fit
that other types of helmets don't offer so here looking at the back again you can see that narrow
tail piece and how it comes down and then when the hinge plates close that's how you get that
complete protection there so to close it it just slips over here rotate 90 degrees and it's locked
in place so after discussion with the owner one of the things that we think is probably incorrect
on this particular interpretation is the additional holes the breaths cut into the visor
if you take a look at this sketch from my friend Augusto you'll see that this is probably more
likely how the visor would have been designed so remember we discussed before that this is
potentially a weak point in the visor that these can be bent or damaged so when you do
take advantage of using the visor and you lower that visor into position you would want to
reinforce that potential weak spot on the helmet itself so having a solid plate here
instead of a plate punched with holes would help reinforce that point of the visor where
damage can occur and when you are wearing the visor you'd typically be wearing it because you
want maximal protection so that's why you would do it there and then of course the visor itself
rotates on pivots very similar to the way a bassinet functions with pins that are removable
on either side so that the visor can be taken off the helmet all right so now what we're going to do
is actually put the helmet on i'll show you how to put it on and off how it functions we'll talk
about things like vision and movement to rotate the pin 90 degrees it'll unlatch hopefully you
can still hear me um now the the mechanism is locked into place and i can see um with the visor
up vision is it's somewhat restricted down here but it's it's really incredible the amount of
the field of view that you get i'm using my old peripheral vision test i can actually see
both my hands right now looking straight ahead so that's pretty good peripheral vision
looking up i do see this out of the top of my eyes but very little is actually restricted
and then it's very easy to see through the picket fence portion it's definitely a feature that
enhances the visibility of this helmet considerably compared to some of the others
if this was completely blocked off with no breaths my vision everywhere from here down so
my hand is now below the level of the picket fence everything from here down would just be black
because of the picket fence i can see my fingers very easily
at this level and then the breath i can still see my hand on this side very easily
um with the visor down i'll put the visor down i'm going to do the same peripheral vision test
i'm not sure how well you'll be able to hear me as far as breathing goes right now it's virtually
unrestricted because of the visor being up and because of the picket fence and the breath
so with the visor down now i can still see my fingers right about here i think it's just a
little bit more in than where it was before it's still very good i do lose a significant portion
of the vision above me and if the visor were designed like we think it probably would have been
with this blocked off i would kind of have a interruption in my vision right here but i would
still be able to see down here in more typical armet designs pretty much everything from so i
can see my fingers out of the actual oculars here so everything from here down would be obstructed
if this were completely blocked off but i would be very well protected i still breathe fairly well
even with the visor down but if this were completely closed you'd start to really be
breathing your own air back in and breathing would get a lot more restrictive as far as
movement goes movement is pretty excellent with an armet you can move your head up and down
side to side is virtually unrestricted as the lower edge of the helmet
floats above the shoulder line and collarbones so that it's not impinging on you you get a little
bit of drag from the avontail but that's really insignificant so rocking my head side to side
if this were fitted to me and sat up a little bit higher it would fit even better there but overall
the mobility provided by the armet is really excellent compared to other designs of medieval
helmets very minimal restriction it's comfortable it's relatively light
visibility is pretty good with the visor up it's excellent in later armet designs i would suspect
breathing can become an issue especially with the visor down and the wrapper plate in place
on later 15th century designs taking it off is simple just turn the pin and open it the
visor will not open with the sorry the cheek plates plates will not open with the visor down
so i hope what you see is that the armet is not only what i consider a very aesthetically pleasing
helmet but it is also very well suited to being a versatile combat helmet without the wrapper plate
on it gets very good mobility around the neck with the visor up it gets very good vision you can see
a lot because of the shape of the later facial openings you can breathe with the visor up with
the visor down breathing does become considerably more restricted and with the wrapper plate on
doubly so because now that air exchange has to go through two overlapping plates but it becomes
considerably more protective so perhaps in a ground scenario fighting with an armet no wrapper
maybe removal of the visor visor up in a cavalry situation you could lower the visor to reinforce
the front of the oculars include the wrapper plate and now you're considerably more protected
that is everything that i wanted to discuss today in the future hopefully i can get my hands
on a late 15th century armet with a wrapper so that you guys can see how that actually functions
in person and until next time if you guys like the video please give me a thumbs up
and subscribe if you haven't already feel free to follow me on facebook all the links to vendors
and information is down in the description and we'll see you guys in the next video thanks bye
