How to clean your bearings! 🐻🛼

Learn to Roller Skate
3 followers
6 Video Views·Jan 8, 2026
Comments are disabled for this video.
Welcome to Retro's Maintenance Shop.
Today, I'm going to show you how to remove and clean your bearings.
All you're going to need is a skate tool, bearing wash, and bearing lube.
Step one.
Let's remove those wheels.
Use your skate tool to remove the nuts.
There we go.
These wheels are called Sonar Zen Wheels.
They're hybrid wheels.
You can use them indoor and outdoor.
And this is what a roller skate looks like with no wheels.
What we want to clean is the bearing that's inside the wheel.
First, I have to remove the bearing, and I'm going to show you an easy trick that I use.
I don't use a bearing remover or a bearing press.
Take the bearing and put it on the edge of the part that the wheel goes on and twist
it away from the bearing, and it should pop off.
So all together, there's 16 bearings.
Remove all of them.
Shimmy it off.
Here are all 16 bearings.
Before putting our bearings in the bearing wash, what we want to do is remove the cover,
that red part right there.
If your bearings have covers that are not removable, just put them straight into the
bearing wash and just let them sit for a little bit longer.
I'm going to use a safety pin and just push the safety pin under and pop.
Two hours later.
A lot of people ask me, how do I know when to clean my bearings?
Well, it depends.
How often do you skate?
Do you skate outside a lot?
Look for signs of dirt.
No ----, Sherlock!
Or if your wheels stop spinning, that's how you know.
The other question I get asked a lot is, what are the best type of bearings?
You can use a variety of different bearings.
I use Reds bearings and Better bearings.
There's also Swiss bearings.
Don't mind my face as I try to remove these.
I'm ready to wash.
I'm going to use this little bottle that I have.
Pour some of the lemonade.
Top it off.
Close the lid.
Shake it up.
And now we wait.
Actually, you know what?
I'm going to put my nuts in there too, because look at how dirty the nuts are.
Dirty nuts.
Get in there.
Would you like some bearing juice?
I'm going to let the bearings sit for about 10 minutes.
In the meantime, I'm going to clean my wheels and the bearing covers.
Slowly but surely, turning this channel into an ASMR spinoff.
And I think that the juice looks nice and thick now.
We can fish out our bearings.
Let's see how they look.
Oh my goodness.
If you don't have one of these, you can also use a plastic spoon to fish them out.
You can just use a Tupperware container.
You don't have to have that.
It's so dirty.
I'm going to put them on a towel so that they can dry.
Next, we're going to lube our bearings.
We have to make sure they're nice and dry.
Take a towel and rub them down.
I recommend leaving them to air dry for at least half an hour.
I'm going to dry them with a towel now.
Once your bearings are dry, you can pick whatever oil you want to do.
Just apply two drops, one on one side on the ball bearings and one on the other.
If your bearings don't have a cover, then you can just seep them in the bearing oil.
Roll the bearing to get the oil nice and saturated.
And then we're going to just pop the cover back on.
There we go.
And repeat that process with all the bearings.
One, two, spin, spin, spin.
So now I'm going to show you how to put the bearings back on the wheels and put the wheels
back on the skates.
Put the bearing into the part that it's supposed to go in.
You can push it in, use your fingers.
You can also place the bearing on the skate, cover away, put the back of the wheel onto
the skate, press down, and the bearing will be fitted on.
Same with the other side.
Put the cover face down and put the wheel over and press.
And there you go.
You want to put the wheel back on the skate, take your nuts that you've cleaned.
You can use your skate tool to tighten it.
Time for the rest.
And that's it.
Now you know how to remove, clean, and put your bearings back on your skates for a smoother roll.
Thanks for watching and I'll see you in the next video.
