New Voyager Feathers Full Review With Broadhead Test! Do They Live Up To The Hype?

LEARN ARCHERY
7 followers
2 Video Views·May 19, 2025
New Voyager Feathers by TTT Archery fully tested arrow for arrow against traditional shield cut feathers and is there any advantage?
What's up guys? Thank you for joining me today on Instinctive Addiction Archery. I am your host
Jeff Phillips. Got a super cool one here for you today like nobody's done yet. Okay, you guys know
how I am. New products come out. I can't wait to test them. Okay, so check this out. My friend
Trevor Fielder with Triple T Archery, him and Paul Helms along with a couple of others that have been
working on this stuff have come out with a new feather. A new traditional feather called the
Voyager. Three inch, four inch, and five inch. Okay, and they named them the Nenna, the Pinta,
and the Santa Maria. Well, these are the Pintas because they're the four inch. Okay, I like four
inch feathers. Anyway guys, these feathers have been extensively tested by these guys but not by
me. Okay, so when Trevor contacted me about these new feathers before the launch, I was of course
really interested in them like always. And guys, first I want to show them to you and I'm sure
there's going to be a lot of videos out about these feathers and what's different about them,
but let me tell you what we're going to do today. I got the Hooter Shooter set up, dialed in, and
what we're going to do because they claim that they found in their testing that these feathers
carry the arrow a bit further than a standard feather would. In other words,
the cast of the arrow, the arrow doesn't drop as fast which would do what? That would extend your
effective range. Sure, whether you're an aimer or instinctive or whatever, that would be a game
changer. Okay, so the only way that I knew to really truly test this and the really good flight
characteristics of the arrow in itself, the feathers, why they would be different is to test
them out of a mechanical shooting device. That's right, with a bow that's strapped in, it just
cannot move. Okay, so let me tell you what we're going to do here today. And guys, again, I hope
you find this test really super cool. Alright, so if you look closely at these feathers, you will
notice that the design is quite different. It is. The front is not shaped like a traditional feather.
No, it's not. It's completely different. So is the back. It is. So with that, they
believe that there is less noise with the feathers, more stability, that these arrows actually
stabilize way quicker as the arrow leaves the bow to spin the arrow much better, even with a
standard, like I'm running a five degree left helical on mine, as all of my arrows. I mean, when
I fletch these, same jig, same everything. And I will tell you guys one thing, these feathers,
and I sent Trevor Fielder a message about this as soon as I did it, the night that I built these
feathers here, these arrows, I noticed that the bases on these feathers glued down much easier
than others that I had been using, much easier. The bond was incredible. I did not even use wraps.
I'm shooting Obsidian 3K carbon arrows here. And it was an instant bond. I didn't even really clean
the carbon very much at all. Just a little quick wipe with some denatured alcohol. And I mean,
with super glue, the Gorilla super glue liquid blue lid, that's all I did. And then of course,
I put one drop of Fletch Tite on the front because it always protects the front. But what
I'm noticing is these are not pointed and sharp on the front, like a standard shaft that would
actually get into your finger if it was direct across your finger. Those things are pretty
dangerous. That's why a lot of the Chinese arrows come with a little rubber shrink wrap around them
to protect that as a liability. So these don't have that. Now I shot them right after I built
them. They flew amazing, beautiful, beautiful flight. They really, really did. So let me tell
you about the arrow setup and we're going to go ahead and start our testing process. And we'll
tell you how we're going to do this. All right. I've thought about this long and hard. Jeff,
how can you give it a really, really, really unbiased test against standard four inch shield
cut feathers? Okay. Like I always shoot, this is what I've always shot. I love them. So how can I
compare the two? How can I really, really, really compare the two? Is it true that the cast of the
arrow is going to be a little further? How? I can't do it manually drawing the bow because I
may anchor just a touch different. I might execute a little bit different in my pull through and
expansion. Bow could have a little more energy on one shot versus the next. Well, that's not
going to happen out of a mechanical shooter that draws to a very specific, and I set it up for 28
inches today. So it's a 40 pound bow. Makes no difference what pound is the bow is, but I've got
a 40 pound ILF Hermit X10 in the cradle. All right. Shooting a 491 grain arrow. Now I'm going to show
you guys what's up. I weigh these things. They are identical within a half of a grain each.
Identical setup. These are 500 spine, Obsidian 3K, 7.8 grains per inch, running 100 grain brass
inserts, 150 grain stainless tips. And I'm actually running the Sanleda Nox. I love their Nox. Their
Nox are just killer. So anyway, they fit these shafts and that's what I'm running. So when I put
these on the scale and I'll show you guys, get it to be still for a minute. I've got a good bit of
FOC. I'm going to show you guys what this one weighs. I'm going to show you what the lime green standard
ones do, what they weigh. So you'll know that we are dealing with the identical, as close as you can
humanly possibly have two matched arrows for its impact on the target, which is at 20 yards right
now. So I've dialed it in at 20 and the way I figured that I could really see how this cast
goes is not to move the machine, not to move the bow, not to move anything. Simply move the target
back. As we start getting natural arrow drop, a 500 grain arrow out of a 40 pound bow should be
around 25 yards. But wherever we see the natural drop, that's where we will see if one arrow
outshines the other in cast. All right. So that's what we're going to do. So take a look here, guys.
There it is. 491 grains. Okay. That's 491 grains. Let me set this back up for a second.
That's the pink one. Okay. Now we're going to weigh this. Same thing.
We're going to sit still there for a second. 490 even. We're going to sit still.
There we go. It's 489.4. It's just kind of moving a little bit within one grain. Okay.
So we are truly within one grain, right? So I'm fixing to load the bow
and we're going to shoot this thing, guys. I'm going to show you what kind of impact we're
getting. I'll move the camera over here just a little bit where hopefully you guys will be able
to see the target. Got a white line across. There is an arrow dead center of that piece of tape
right now at 20 yards. So I zeroed the bow in at 20 yards. I'll shoot a duplicate
first test arrow. Make sure that we're still set up good and nothing has moved.
Right in the middle of the tape. Just a little hair over to the right. Dead middle of the tape.
So up and down, the bow is not moving. And that's why I wanted to use this thing
to show you guys that a bow that's not allowing any difference of a setup like this, it doesn't
allow any kind of elevation differences. The arrow's natural trajectory is going to show.
Good or bad, it's going to show. Okay. So dead in the middle of the tape,
we will shoot a standard and it should be in there too. I had not done this. I haven't shot it. This
is brand new. You guys are seeing it as I've set it up. We're going to learn together. So
that's the way I like it. A test is a test. Dead on. Okay. Should be the same.
They're almost touching. They're both dead center of the white tape.
Both areas. And they're only like that far apart maybe. So, okay. Very, very consistent. Feather
to feather. 20 yards. There is no difference. I can't see any difference in the flight or anything.
Now, I would have to run super slow motion with a camera capable of somewhere around maybe 4,000
frames per second to see the arrow in super slow motion, one compared to the other, how quickly it
does stabilize. I would think that these Voyager feathers do stabilize a bit quicker because of the
height of the rear end of the feather. The height seems like it would be a little more stable,
especially in crosswinds. I think there would be a big advantage there, which that would be
an absolute plus. But the design, from what I understand, even having a little taller feather,
kind of like people running blazer vanes, they stabilize an arrow in flight very, very fast,
which is a plus. But the design of these, the way they have shaped them because of the
aerodynamics and the fold, they don't make noise. Okay. So I have not noticed with my ears,
shooting them out of the bow by hand, shooting them out of here, I have not even heard these
feathers at all. I cannot hear anything in flight. So that's a plus because believe me,
I've used some feathers, even actually five inch traditional shield cut compared to a parabolic.
Yes, I can hear them. I'm not hearing anything out of the Voyagers. And I do believe it's because
of the way that they've got these cut that you just don't get the wind noise. So brand new product
to hit the traditional market. Okay, guys, I'm going to grab these right quick and we're going
to move the target out another five yards. Going to go to 25 yards, see what starts to happen here,
not touching anything on the setup. Be right back. All right, fellas, 25 yards. We are at 25.
First up, we'll shoot the standard traditional shield cut four inch. These are actually
three rivers shafts, three rivers feathers. They are the exact same as a true flight. So
just like a true flight. All right, let's do it. Dead on. Now when I say dead on, I'm going to
show you guys, I've had guys ask me on some of these tests that I've done out of here,
some of the things. Now I had some people, you know, somebody is always going to comment
something goofy off the wall, but whatever. I've had a couple of people comment and say,
well, man, I counted the clicks on that thing, you know, and you click one or two more times
on certain areas versus the others on that heavy versus light shaft stuff. That's bull.
This is a boat winch. And by the time you unwrap the cord, it is not going to click the same times
every time. It's not electric, but it's drawn at the same spot. And I'm going to show you guys
how I'm lining this thing up. So you will know. I don't care. It's it's, it is what it is. I draw
it to the same place. It does what it does. Heavy areas, light areas, different feathers, whatever.
I want to know. I'll do. That's why I do this. That's why I built this thing. So check it out
guys. Uh, if you can see, there it is dead on 28 inches. There is the 28 inch mark right there.
28 inch mark. So I'm backing up, closing my left eye, looking at my right eye and I'm lining it up
dead on every single time, the same way every single shot, because I don't want it to be any
difference. Cause you know why? If it's different, I'm not going to see the true results. Okay.
And I want the true results. And guess what?
