How I built Gipsy Danger From Pacific Rim In A Stormy Ocean #scalemodel #3dprinting #pacificrim

Scale Model Geek
93 followers
I really loved the design of the Gipsy Danger and wanted to recreate the scene when it saves the trawler from the Kaiju in the opening of Pacific Rim.
A movie from the master film maker, Guillermo del Toro.
---------------------------------------------------------------------
INSTAGRAM: @scalemodel_geek
ETSY SHOP: https://www.etsy.com/au/shop/ScaleModelGeek
3D MODEL FILES: https://www.cgtrader.com/designers/scalemodelgeek
---------------------------------------------------------------------
#modelkit #modellers #scalemodel #scalemodelkit #scalemodeling #scalemodels #plasticmodels #diorama #3dprinting #3dprint #resinart #scifi #apocalypse
I'm the Scale Model Geek and thank you so much for joining me for another build.
This week I'm building Gypsy Danger from the movie Pacific Rim.
Now I'm really happy with the way this print turned out the detail is really really good in this
and the parts fit really well. What I'll be doing in this build is I'll be actually putting him to
a diorama in a ocean a very turbulent ocean and also I'll be adding some LEDs and that's why I
printed up his body and his head in clear. I've never worked with LEDs so this could be a really
interesting experience. It could go really really bad very very quickly. I went out and purchased
these five millimeter LEDs. Now I'm using 12 volt power supply and which means I need to use some
resistors. Because these LEDs are only 2.1 volts I actually have to use these resistors to knock
down the power. With all those bits sorted out it's time to start prepping the parts.
I'm just using some resin here and a UV torch. I'm just filling up these little divots that were
created by the supports from the actual printing. Now I need to use some of this liquid mask to
cover up some of the areas that need to remain clear. It's actually pretty good stuff. I did
make the slight mistake here where I should have probably used a bit of masking tape around the
actual fins of the turbo there. It was a bit of a pain to get out but in the end it actually worked
really really well. Happy with this stuff. Because there were so many flat surfaces I needed to do a
bit of sanding. Now I'm using this 800 file board and it was a bit of a chore when I thought I might
be able to get better results if I just use the wet system. I pulled out a baking tray filled it
up with water and off I went. Hopefully the wife won't see this or else I think I'll be in big big
trouble. This turned out to be a much much better system. I was getting such good results. Really
nice sanding in there. No dust as well. But I've got to say with all the flat lines on this print
it was a bit of a job to get through them all and right here I actually noticed that I had a big
split in his leg but luckily I'll be chopping off his leg or lower portion of his leg because
he's going to be in the ocean. I do recommend wearing gloves because what happens after you've
had your hands in water for a while they turn to prawns. Now I did need to file some detail off his
butt just so I could get to the sanding a bit easier but it's some detail I can easily replace
a little bit later. He's looking really really good. Really happy with the finish on that.
A little trick if the edges get a little bit gnarly just cut them off with a pair of scissors
and you're good to go again. Now it's time to replace some of the detail I had just filed off.
I'm using this really thin piece of plastic card and this punch set.
All I'm doing here just punching through the plastic and creating these little discs
and that'll be my detail that I'll replace on Gypsy's butt and I'm just adding these little
discs using some super glue. Once again a bit fiddly but it was actually worth the extra work.
Here I'm just trying to work out how I'm going to run the wires through his leg.
I figured if I drill a small hole here I could run it straight up the middle of his leg and hide
it at the ball joint and at the top of this part I drilled a small hole first and then
kind of grinded it out so it just gave me a lot more room a lot more space to actually run the
wire through and just a quick check where I need to drill the hole into the torso. Now I'm just
chopping off the bottom half of his lower leg and I've set up the vacuum hose and you can see
how well it's sucking up all those dust particles. At the end of these pieces of wire I've actually
tied little knots so when I pull through the wire it doesn't actually get pulled through the whole
lot accidentally. I was actually dreading this section of the build but it turned out to be
really easy to do. Now in this area for some reason in my head I thought I need to do all
the wiring and position into place first and I started gluing together and you know in
retrospect when I look back at it I could have easily just painted them all separately which
would have made things a lot easier for me and then glued them into place. So time to do these LEDs
and who knows what's going to happen here. Look at that it actually worked first go.
Now that was even a surprise for me and with the LEDs you put the resistor onto the short leg
which is you can see by a black wire the negative side. Here I'm soldering the LED wires to the
main body wires and throughout the whole build of this LED section I kept on testing it just
to make sure it was all still going well. I must admit during this whole portion of the build I
was a bit paranoid with the LED wiring. Just pushing both LEDs into the body I've got a green
one and a red one. The red being for his chest and the green for his head. Now this section was
an absolute drama because the only access I had was through his head trying to get the LED in
the right area took me almost an hour to get it right. But I got there and the shake test to make
sure it doesn't move and it came out great and right about now as I was placing the head on it
went down a toilet. Somehow actually broke the joint in there so I had to pull out the whole
thing and re-solder it and start again. Now just masking up the visor. It's actually to be a bit
more accurate I think it's the you would call it a windscreen because it is a cockpit inside there.
I was very careful to make sure I got a really sharp edge to the tape
just to make sure no paint seeps underneath the masking tape. Now talking about masking tape
I'm just using that as well to cover most of the engine bay there and then using the liquid mask
again finish that off. And now it's time to paint Gypsy. I'm using this IDF blue for the base color
starting with the head his arms and the rest of him and I'm using this black for the mechanical
areas and for some reason every time I seem to touch Gypsy during the painting process
I seem to get black paint everywhere made an absolute mess. In the meantime please help me
grow and smash that like button subscribe and hit the notification button. As I was saying what a
mess I was making. So a bit of cleaning up to do once again with the IDF blue. What I've done here
is I've printed up some of the markings that I need to have on Gypsy Joker. Now I've already
pre-coated him with some gloss paint and I printed this on some white based decal paper through my
laser printer and I created all those lines in Photoshop. I'm just cutting them to size and
once I've done that just a matter of placing it into the area I need it to and a bit of Mr Mark
softer so it conforms to the body shape a lot easier. More fiddly stuff but as always worth the
extra effort. Now Gypsy Danger has a couple of numbers on his shoulders there the number 34
on each side and I thought since I don't have a printer that prints white I'll just print an
outline of the actual number and then cut out the number but boy did this turn out to be a disaster.
No matter how hard I tried I just couldn't get the right shape I could not get a crisp number.
In the end I just ended up giving up and I think I'm going to have to invest in the printer that
actually does print white. So I retreated back to the lines because they worked. I was really happy
with the way these decals were working they added just that extra bit of pizzazz to the actual
figure. Now I'm just putting on some of this artwork onto his chest very reminiscent of the
GT stripe across his head because that makes him 20% faster. Apart from the numbers he's actually
come up really really well with the decals and off camera I gave him a coat of flat clear.
Now to detail some of those black mechanical areas I'm using this gun metal from Ammo which
is a dry brushing paint so it's really really thick and dry brushing is actually one of my
favourite areas of painting. It really brings out the detail. A combination of the IDF blue and some ivory
white to do some of the highlight areas for the dry brushing of the body and Gypsy is really
starting to come to life now. The details starting to pop. I'm just using some of this metallic grey
to add some more details to his chest. My go-to bases are usually picture frames and this is a
6x4 inch frame and off camera I drilled this 10mm hole to actually fit the power plug
which off camera I've already wired up and I created these little facades with this plastic
and I just glued on some nuts and bolts to it. Once that I printed it up on my 3d printer
and I just super glued that into place and the wiring I just used some hot glue
and I'm just penciling out where I need to drill the holes.
With the holes drilled out I use a ton of hot glue just to make sure he's fitted securely
onto the base and here I'm just soldering the plug wires to the actual figure wires.
Quick test to make sure it all works and it does. Sometimes I even surprise myself
and here we go time to remove the masking tape off his cockpit windscreen and really happy with
the way this came out nice sharp lines. Now I probably should remove this before I actually
glued him to the base but it is what it is and I'm using just five minute two-part epoxy glue there
and like I said five minutes gives me a lot of time to actually position him to the place where
I need him to be just to make sure I've got plenty of time to get the pose right.
Any shoulder thingamajiggers and they'll just super glued into place.
Now for some panel line accent color for his lines in the body. This really brought up even more
detail. Now before I actually start creating the ocean I need to mask up the frame so I don't get
paint all over it. I'm just using some of this packing foam and I'm going to use my hot wire knife
and just shape the foam into rough looking waves
and with the shaping I'm sort of guessing how the waves are going to look.
I know I need quite a large wave in front of him and some smaller ones behind him
and with the hot wire foam cutter it just makes it really easy to get the shapes that you really need.
Now I'm just using a PVA glue to stick it all down and to create the actual texture of the
waves I've got some aluminium foil here and I'm just scrunching it up to get the rough shapes that
I need and some wire here and I create a little u-pin to keep it into place and again some PVA
to get the aluminium foil in place and more pins to hold there while the glue dries.
Now I'm covering the whole area with some PVA glue and I'm using some bigger pieces of aluminium foil
and this is kind of just to soften up the texture a bit
so it gets slightly more wavier more in scale to actual gypsy danger.
Now with some thinned out PVA glue I'm just giving it a complete cover just to make sure that when it
dries the paint has actually got something to stick to otherwise the paint will just peel off the tin foil.
Now I'm using a combination of the green and the black and I'm mixing it so I get a really dark
deep green to this and that'll be my base ocean color. Now I chose a green over a blue because
it gives it a much more moodier feel to it, feels colder. Now I've added a bit of white to it
and I'll be painting the top areas of those waves. Now I'm adding a bit more white to the paint
and we're going to go over some of the more raised areas
and slowly building up the tones of the actual base color paint. You can see some take shape now
they're starting to look like waves and I've used some more white in the paint and really
hitting the top edges this time sort of like the crest of the waves. Now I decided I wanted
to add a bit more blue to it so I mixed up some black and blue paint and just dabbing it into
the recessed areas just to add a bit more color interest to the overall picture. It's looking great
look at that it's actually looking like an ocean. Now some of this impasto gel which is a medium
paint it's a thick clear gloss paint and I'm going to go over the whole ocean area with it
and that adds slightly more texture to it but also gives it that gloss finish. Now I also need to add
some of the gel across his legs so it looks like just water's running over it. Now to use some
cotton wool for the splashes and I'm thinning it out here so you know it comes becomes fairly
translucent and using the gel the impasto gel to glue it in place. I'm just adding some impasto
gel across the cotton as well and some more cotton at the crest of the waves. Now I printed up this
little tugboat in my 3d printer and I added some bars to it to make it look like a trawler
and painted it white and now I'm actually painting the bottom of the hull black.
I'm using this panel line excess color to actually add to the crevices of it just to
add a bit of depth to it. It's hard to dry brush white when there's nothing lighter than white.
You can see it's popped out the detail there and now I'm just using some PVA glue to hold
the trawler into place and of course we need some splashes for the boat as well
and look at that it's all done. I think it's time for the hero shots.
