Making A Retro Future Hovercar From A AMT 1940 FORD COUPE #scalemodel #3dprinting #diorama #scalemodelkit

Scale Model Geek
93 followers
I build the AMT 1940 Ford Coupe kit and turn it into a weathered Retro Future Rat Rod hovercar complete with female racer.
-----------------------------------------------------------------------
INSTAGRAM: @scalemodel_geek
ETSY SHOP: https://www.etsy.com/au/shop/ScaleModelGeek
3D MODEL FILES: https://www.cgtrader.com/designers/scalemodelgeek
-----------------------------------------------------------------------
#modelkit #modellers #scalemodel #scalemodelkit #scalemodeling #scalemodels #plasticmodels #diorama #3dprinting #3dprint #resinart #scifi #apocalypse #ford
Welcome to the Scale Model Geek and this week I'll be building this AMT 40s Ford Coupe.
Now this kit originally came out in 1960 and boy does it show. Over the years it's had a few
re-boxings, new artwork and that type of thing but they've actually never retooled it.
So I'm going to modify it and turn it into a hover car with these engines that I created
in Blender. The round ones will be my hover modules and the longer ones will be my thrusters.
Basically a bunch of rockets on each side of the car. Now I did create these in Blender
and it was just a matter of using a whole bunch of various parts and effectively greeblies from
the 3D world in virtual reality. Now I downloaded these greeblies from Thingiverse and in Blender
I seriously know probably less than 10 different tools. I just need to know things like flip,
rotate, duplicate, those type of tools and that's enough for me to actually put these little
greeblies together and to create this engine. And as you can see as I build up the little bits
and pieces it comes together quite well. And in this particular engine I've used bits like
warhammer components, robot legs, some thrusters from a jet engine and with all those greeblies
in place I was able to get the look that I needed. And the great thing about it I can now print
multiple versions of this. Now of course I use the same technique for the hover modules.
And for the figure I'm using this little one that I got from Loot and as soon as I saw the concept
bar for this particular figure I knew exactly what I want to do with it. The detail is absolutely
amazing and what's wonderful about it is they're pre-supported so all you have to do is throw it
on the build plate or rather the software and print the little sucker out. And look at that
detail it's absolutely fantastic. Now this figure is supposed to be 75mm which is perfect for
1 24th or even a 1 25th scale vehicle. Now it's time to get into the build and as soon as I opened
it up I had a look at it and thought yeah okay we're going to have some issues with some of the
parts because they're rough as guts. A lot of flash on the plastic parts. During the process of me
trying to work out how I'm going to mount the engines I decided to actually seal up the wheel
arches. I'm just using some plastic card which I scored and then snapped into place and I did
need to do some bending to get it to the right shape and this stuff's pretty thin as you can
see so it's just easy to do with a pair of scissors in this case. Here I just used the Tamiya extra
thin plastic cement to glue it into place and once that was dry I actually cut out another piece and
laminated to the top just to fill out the depth difference and then I just filled it up with a
bit of putty. Even though I filled up all four wheel arches I will be cutting out the front ones
because I needed actually a small arch. Now here we go with the putting and sanding and there was
quite a fair bit of it. Because this kit is so old over 60 years old in fact there was a lot of
flash that I needed to clean up and also some seam lines. Over those 60 years it's never been
retooled so I guess it should be expected. There were a whole bunch of parts that I didn't need to
use so they're going to end up in my greeblies box. Now I did need some parts from the chrome
section so I needed to strip them because I'm not going to have any chrome bits on there and to
remove the chrome I use some of this Easy Off Oven Cleaner, the heavy duty stuff. It's very toxic
so make sure you wear gloves masks and do it outdoors but it does work a charm. Now I needed
to do some modifications so into my real greeblies box and I just added some details into the center
tub and I moved the steering column and you'll notice a bit later it gets moved back again
and some more greeblies just to detail the back seat, well what was supposed to be the back seat.
Now I decided to use some of this Earth Yellow for the base color of the interior.
Now I did the ceiling of the car, two seats, it's got a great retro feel to it and of course the tub
and you can see the steering column has already been moved. Now to add a bit more detail I'm using
this Accent Color from Tamiya, the Deep Brown and I'm just running it into the recess areas just
to give it a bit more depth to the actual kit part and a complete wash to the tub and some of
the excess just remove with this cotton bud. Now I'm using this Panel Line Accent Color in Black
from Tamiya, I'm just running that across the details that I've put on the back seat.
Now I am weathering the windows so I'm not sure how much of that detail you end up seeing through
the weathered windows. I'm using this Black to paint the modified dashboard
and these are the dials, the speed dials, tachometer and that type of thing and yeah the steering
column as well and some of the steel to add a bit of detail to the gear shift. Yeah yeah I know
there's no gears on a thrust of an engine. Now a combination of this Sand Ivory and also the Off
White and I'll be doing that as the dry brushing to highlight the details on the seats and the tub.
Yeah just super gluing them into place. Oh that's looking good. Now I'm just using this
circle template to get me the size that I need to cut out for the arches. Now I think they turned
out to be about 22mm maybe 23mm if I remember rightly and just using a Dremel tool slicing
into it and snapping it off and once I just used the side cutters to snap it out went back in with
the Dremel tool with a filing disc or drum is it a filing drum and cleaned it up. It's got a great
shape to it too, came up well. Now I'm just working out the size of the axle that I need.
This is the engine that I 3D printed and I did the same thing as I did with all the other parts,
a whole bunch of greeblies that I put together until pretty much the look that I needed and I
wanted kind of these glowing modules on top. Now with the engine all ready I just need to cut out
the back section or rather the boot to place the engine in there. Now the reason I printed
up in clear is so I can add some LEDs through the back and there's my glowing engine. Yeah I'm really
happy with the way that's looking and they're just a couple of three volt LEDs. Now I've masked
out the area I need to cut out and I'm in with my Dremel tool once again. First off with the cutting
disc I get it to the size that I need it and a bit of cleanup with the file and a bit of sandpaper as
well. Here I'm just marking out the shape I need for the actual base of the engine because the
engine has to sit on something. Now this is the engine super glued onto the base and the LEDs
will pop in there and I'll just cover the whole thing in araldite to secure it into place.
And this is just a two part five minute epoxy. Now you can see I've had to cut out a section
there in the wheel arch because the um the base of the engine got in its way and I did add half
a hover module just to keep it all balanced and off camera I actually modified this plow that I
actually found on Thingiverse as well. I'm using this 4.8 millimeter channel because I'm replacing
the original bumper bars with this. Super easy to cut and again a bit of glue to hold it into place
pretty straightforward there and then I'll stick the plow onto that but of course I need to use
super glue on that one just making sure it's all straight. For the rear one I did need to
bend it a bit so I'm using the hair dryer here just to soften enough just to get enough bend
into the actual piece before I glue it to the struts and there you go all super glued into place.
Now I'm just masking up some of the areas that I want the glow to come through
from the LEDs and once I've masked it up I just run a pen across it just make sure it's
the recessed areas or rather the corners are really nice and firm and here I kind of screwed
up the first engine I made the undercoat way too thick and I just lost so many um so much detail
there. Luckily I had another one so went through the same process but this time I did three really
light coats and that retained all the beautiful crisp detail in the engine. Now to start painting
all the engine components in black that's the base coat be doing the engine the thrusters and
of course the hover modules and to add a bit of life to those components I'm using some of
this gun metal from Ammo and I'll be dry brushing those units and this dry brushing technique really
brings out all the detail as you can see there looks pretty awesome and in certain sections I'll
be using some of this light metal again from Ammo and I'll be just hitting some random areas just to
add a bit of visual interest to the components and if you haven't already hit that like button
and subscribe to the channel it'll be greatly appreciated for your support and it's looking
really good look at that detail popping. Now I'm going to hit a couple areas with some of this
clear orange from Tamiya again it's purely just to add a bit of visual interest make it look a bit
or rather techno-y look at that so I look like something finally. Now for base coat for all the
body work I'm using some of this rust and this is the first color that I need to create for my
hairspray chipping effect I'm just making sure I get a nice even coat over the whole body next coat
will be this red brown but I'll be doing a bit of an uneven mottled effect over the body with this
I'm just hitting some random areas again straight a bit of interest to it
now with this light rust from Vallejo I'm just going to hit some of the more prominent edges
like the wheel arches and also the edges of the cab and for the chipping effect I'm using some of
this hairspray which I sprayed into this small little bottle and then I use that little bottle
to put into actually my airbrush. Now I'm just doing a nice even coat to start off with
and then a bit later on some of the areas that I really want to be heavily weathered and slightly
chipped as well rather cracked I went in for another two or three coats. Once that was dry
and I left it probably for about two hours I used some of this Tamiya masking tape and I started off
with the six mil stuff which turned out to be a bit wide with the six mil I actually struggled
to get around some of the curves so I ended up going back with the two mil and then over the top
of that the six mil again and then the rest with some of the masking tape just the general purpose
masking tape. Once the masking was all done I went in with this insignia white and I sprayed the bottom
half of the cab and of course to paint the rest of it I had to go in and mask off the wide area
and the rest of the paint was this a light blue from Vallejo and there it is that's my two colors
looks really cool and retro and now it's time onto the chipping I'm just using this little brush to
start off with and I'm dipping it in water and going over the areas that I want to be chipped
away and what this is doing is actually going through the paint hitting the hairspray and
actually dislodging the paint from the surface and that's how you end up with your chipping
and this is like the second time I've done it and I absolutely love this technique I ended up using
a toothpick as well as a toothbrush to actually get through some of the paint these are the areas
that I actually did a thicker coat of hairspray and you can see it's chipping off a lot easier
and in much larger chunks and there it is all the chipping done it looks really cool
but it is a bit contrasty between all the colors so we need to go to the next process of the
weathering and for that we're going to use a bit of a wash or two starting off with this dark brown
from Vallejo first a spritz of water so the actual wash just flows a lot easier
and I'm just smothering it with this wash now before I did the wash I actually gave the whole
car a bit of a coat of flat clear just in case something goes wrong and I need to remove some
of the wash my other colors are actually protected as you can see I'm being very very generous with
the wash definitely not shy with it now I didn't do any chipping on the plow because I actually
want to do some metal dry brushing on there just to wear it back to metal with the wash all done
I'm using some of this dark grass to add some streaking to the actual panels so where I have
some of the edges of the heavy rust I'm just adding those streaks to those areas
and just to add a bit more visual interest I'm using some of this rust
I'm just adding a few more streaks to some of the areas that are already added streaks
and with the lighter rust color just gives it the impression there's some newer rust forming on the
bonnet and the rest of the car I've got to admit I'm a thousand times happier with the weathering
I did on this particular car than I did the original beetle the alien apocalyptic scene that
I did a few months back it feels great to know that I'm moving forward with my weathering
here the streaks just about dry now it's on to the next step and for that I'm using a combination of
this brown iron oxide as well as the sepia I'm combining these two to add some of that real
flaky rust and I'm just adding that around to some of the edges now in this particular case
I'm being really really cautious simply because I've actually never used this stuff before
you won't see underneath the car once the actual car is put into place but I thought I'd waste my
time dry brushing this area for the plow I'm just doing a dry brush of some metal color because I
want it to look worn rather than chipped now on to the windows that I mentioned earlier time to
weather then now I'm just creating a mask here for the windscreen wipers now it actually took
me a couple seconds to work out how these windscreen wipers work because on these old
cars they actually wipe from the outside in when I looked at it first it kind of confused me of the
positioning of the actual windscreen wipers now I'm giving a really light wash of the insignia
white and in retrospect I think I probably did it a bit too heavy end up doing like three light
coats because it looked kind of thin but once I put it on the car it kind of yeah came out a bit
a bit too much so next time probably one maximum two coats and there it is all pushed into place
now I've put the tub inside as well now that's permanently glued into place
and just as I thought heavy weathering on the windows a bit of the detail
is lost behind those windows can't quite see clearly just simply gluing the engine into place
and that's all being blacked out off camera I glued the supporting rod into the chassis
so happy with the look of that so far and I'm just using some of this old Revell
glue and trust me it's old this particular container is like 20 years old now it's been
sitting in my stash and it still works fantastically I rarely use it but I thought in this case it'll
come in handy and there we have it the whole body's now glued together and I gotta admit I'm
really happy with the way this car's come up and with the body all done it's time to glue on the
thrusters and the hover modules and get it looking like a hover car and because I'm using
super glue here I was very cautious and took my time to make sure they were glued on straight
now for the actual hover modules I'm using this five minute epoxy resin
all I did with the hover modules here was I placed some of that adhesive onto the actual
and just plunked the car straight on top and that gave me five minutes to actually adjust it to make
sure it's all straight of course I need to unify the engines with the rest of the body so I use
some of that wash that I used earlier and there it is the retro future rat rod is done ready to
be placed on the diorama but of course we've still got one more thing to do and that's the figure
so let's put that aside and get stuck into the next section it's time to paint the figure but
we've run into a bit of a problem she originally printed at 85 millimeters which makes a very very
tall woman in fact makes a six foot seven or 205 centimeters in height when you compare it to the
car she is way tall way too big to fit in the car I had to shrink it down in chitter box down to 72
mil which made her fit the car which is 1 24th scale perfectly now we've got the sizes all worked
out it's time to actually get onto the painting of the figure now I'm a huge fan of Mobius and I
absolutely love the work that he does he uses a lot of bright colors in his artwork and I
actually want to reproduce that in this particular figure so I was going to go for some pretty garish
colors some yellows reds and blues now I started off using the Vallejo yellow for her vest then
some of this sky blue for her jeans or pants not sure if they're jeans now I'm just blocking in
the base colors at the moment for her jacket some of this red and then onto the saddle brown
for the boots and a helmet or rather the leather bits of the boots well they look like leather
then the black for the metallic areas which be the boots and also some of the armor that's
on the jacket she's going to have some blonde hair so for the base color of that is some of
this sand ivory again from Vallejo now I'm just using a combination of those primary colors that
I used and just adding a bit of white to it getting a lighter shade and just going in brushing
or rather dry brushing those areas I was really happy when I saw this because the pose really is
very realistic and natural when I saw it like I said earlier I knew exactly what I wanted to do
with it and it really suits the whole diorama in the car she really looks like a hot rod girl
and here I'm just adding some dry brushing with metallic paint
to the boots and also the chain that's around her hip and some of this light sand for her blonde
hair there she is almost complete now onto the face sorry guys I kind of forgot to record that
section anyway onto the base now because I need to add a battery pack for the led lights that are
in the engine I'm just using some of this XPS foam and this hot tool this part of my Y cutting
little pack and just melting out a section for the battery pack to fit in make sure you're wearing
a mask for this because the fumes can be quite toxic using a hot tool and XPS foam makes it
really easy to actually cut it out now a quick test fit of the battery and I need to work out here
where I'm actually going to run the wires now I've pre-melted a hole for the rod and a little channel
for the wires to run to the battery pack and I just used the five minute arrow die to glue the
rod into place don't use super glue it doesn't work it actually melts the XPS foam now time to
paint the base just some of this acrylic project paint and I just apply a nice even coat over the
no real reason for their mother to create a bit of interest to the road
otherwise it'll be just black while I was brushing on this deck tan I made sure I went across the
tape rather than with it so to avoid actually any paint running underneath because XPS foam
is porous and I end up with some quite sharp lines and I can't just leave it black like that
I need to do a bit of weathering so I'm using some of this raw sienna and I did add a bit of
black to it and created a wash to go over the whole base once I got a nice even coverage of it
just a bit of paper towel and dabbed up most of it and there it is now time to assemble my
components this plastic tube slides right in the middle of the chassis as well as the base
now I just have to wire up these leads for the power to the led
and to keep them into place so I use a bit of solder and tape them up with some electrical tape
a couple double a batteries make sure they're in the right way
and this battery pack actually has the power switch on there which makes it really really easy
final step is to super glue the figure into place
and there it is absolutely completed and it's a nice little picture frame I've got to say I had
so much fun creating this weathered car it was such a wonderful experience for me that I have
to do another one fairly soon I'm so excited that I've got to show you the hero images
