Creating A Hoverbike From A Tamiya 1/12th Scale Kawasaki ZZR1400 Kit

Scale Model Geek
93 followers
Join me as I create a hoverbike from the Tamiya ZZR1400 1\12th scale model and use a new salt chipping weathering technique
----------------------------------------------------------------------
INSTAGRAM: @scalemodel_geek
ETSY SHOP: https://www.etsy.com/au/shop/ScaleModelGeek
3D MODEL FILES: https://www.cgtrader.com/designers/scalemodelgeek
---------------------------------------------------------------------
#scalemodel #kawasaki #scifi #apocalypse #motorcycle #modelkit #modellers #scalemodelkit #scalemodeling #tamiya #scalemodels #diorama #plasticmodels #3dprinting #resinart
And welcome to the Scale Model Geek and my next project is this Kawasaki ZZR 1400.
Now using a combination of some resin prints that I created,
these hover engines will be added and I'm going to create a hover bike out of this. Now I used a
piece of software called Blender and effectively I created the engines using a whole bunch of
kind of cannibalized from other 3D models and I assembled it just exactly the same way as I would
any other kitbash kit and those little three or four pieces there just appeared they're actually
mech legs and a bit of resizing and spinning around I created this little engine. Then it
was just a matter of printing it out and I ended up with these two great little engines, great
detail in them as well. Really happy with the way that turned out and the plastic kit I haven't
actually built in such a long time so it'll be fun to actually do something. All my other videos
have been 3D resin prints. I'll be converting this bike into something I've been wanting to do for
quite a while now. So let's get stuck with the instructions that say I need to do the engine
first so the engine it is. I'm just following the instructions step by step here. I'll be doing
the basis of the kit first and then I'll add all the bits and pieces later to customize it.
That's the engine chassis. This is the petrol tank. Now because I'll be filling up all the
areas where the lights are, I'm not too worried about putting backings into them or anything like that.
I'm kind of skipping around the instruction sheet as I go. I went from the engine to the body and
back to the engine again. I'm kind of winging it at the moment. I really don't have a solid plan
of what I'm going to do. I've got a rough idea in my head and it's very fluid this plan so who knows
how it's going to turn out. Some of these things that I'm gluing on
like those carburetors, I have no idea if we'll see them in the final build. So I just screwed in
the engine to the chassis. This is the rear wheel fork. I think that's what it's called.
For you motorcycle builders let me know in the comments what is this thing called?
And that gets screwed into place and my big fat clumsy hands
is such a small little screwdriver. Now that's a single suspension rod there
and some of the braces for it. Sadly because of the way I was fitting the
hover engines later on, I had to chop that off. This is part of the retail section.
Strutty things. No idea what they do but they look cool. Again screwed into place.
It's looking good and the foot rests. I'll be detailing them a little bit later on as well.
Now the front spoiler. Now I will glue these lights into place because I need to fill them
up anyway and I need to fill up the hole so what better way to do it than to use the actual lights
to it. Now a bit later on I did add some aerodite to it because there was a bit of movement in there
and when I actually sanded it kept on cracking. So a bit of two part five minute aerodite that
solved the problem. That's the dashboard. I'm going to just glue in the fuel cap which I'm
going to end up filling and sanding down. I'm trying to avoid it looking like a petrol tank.
Now this is the grill for the front spoiler. Now on the instruction sheet there is a
one-to-one scale size reference so I kind of cut it out roughly then trimmed it up with these
scissors and glued them into place. The handlebars. Now I did do a bit of a mistake when I put these
on. The angle of the handlebars were incorrect and they were just facing too far upwards.
So a bit later on I will need to correct those. At the time they look fine. Now the front suspension
struts. Now I won't need the whole length obviously because I have no wheel.
I had this great idea. I'll just score it and then snap it. Unfortunately it snaps straight
in the middle and lucky you don't hear the audio because I was kind of swearing.
Not to worry it's plastic styrene so you can glue it. We can fix it. We have the technology.
Started from the start just some slippers.
So we get to glue this in place. So we glue this in place and we also
get a screw for it as well. Look at that. I actually own a set of precision screwdrivers.
I have no idea why I keep on using this little sucker. It's too small and awkward.
Like I mentioned earlier we're putting this area up and the taillight as well.
Make sure it's nice and even and also if I guess correctly these are the indicators.
Now start off with 180 grit to get to the rough shape that I wanted
and once I've got it fairly close to the shape to the body contours I move on to the 400.
400 grit or P400.
We end up with a much smoother finish to this.
And this is the hover engine and I've puttied it up because it had some dimples in it from the
supports and I'm just trying to work out how to mount it and I've realized
those rear forks are in the way so I'm going to have to chop them off.
So easiest way to do that is a hobby knife.
Chop it off like so and then using a precision drill do a quick pilot hole
and then insert the rod. Now I'm using this rod because that's going to be my support for
the actual engines. I'm going to end up using a smaller rod that slides straight inside of that
and it's going to make life so much easier.
Now I've decided I'm going to assemble this body fairing. I think it's called a body fairing.
My motorcyclists out there let me know what they call this. A body kit, body fairing, body something.
And now we're going to glue this rod that I've cut to size.
Make sure it's aligned nicely to where I need it to be.
Now this is all the basics all finished off now. I'm really happy with the way that looks.
The body's all sanded and nicely contoured so it all fits perfectly.
The engines are looking good. Yeah I'm happy with the bits and pieces
but I'm gonna have to start I think adding some greeblies now to it.
This is my 25 year old box of greeblies that I've collected over the years.
Mind you I did take a break for 20 years, no modeling whatsoever.
And I just went through the box and picked out a whole bunch of things that I thought
that might work. And right at the top you'll see the little sprue of looks like headrests
to the left now. I'll end up using those for the footrests. I'm kind of just playing around
with it, getting some ideas, seeing how it works. Kind of the trick is kind of to make
sure it needs to be there and it's functional. And I find this this section of the build
probably the most rewarding. I like playing around with greeblies.
You get to experiment, you get to be creative.
These are the suspensions of a tank. I think it was a 170 second scale tank.
And that's the grill of that same tank. And that's I think out of another thing.
They're slowly coming together. It's looking good.
And the goal is just to simply to disguise it as much as possible.
Make it look a bit more futuristic. Now put the body fairing back on there.
Simply just so I can see what areas are still exposed and where I can add some more greeblies.
And I thought he needed some hoses like in the front as well.
And I decided I'm going to add some fins to it. And I just found a rocket or half a rocket that
I had in my junk box. I'm just chopping off the little fins there. I snapped them off after I
scored them. And then glued them on that rear body part. I did have to contour those fins so
they matched the body part. Now the hover bike goes 20% faster. I kind of felt I needed a couple
more fins towards the bottom. Now after having a good look at this front body fairing, I kind of
thought the hole was way too big, the mouth of it. So I thought I might fill up with some styrene
here. So I'm kind of just working out the orientation of how I'm going to actually cut it.
I cut a small piece off then mark it out and just score it and snap it
fairly close to what I needed. And then I'm just marking to add a curve to it.
And of course we need to glue it into place. I also did add some supports on the inside.
Of course we've got to party it up. I was very happy with that. Now to add the engine which
I just showed you was actually upside down. This is where I realized the handlebars are the wrong
way around. So here we go. I have to snap them off. Re-glue them with super glue.
And through the whole build I kept on breaking the handlebars off. You can see the foot pedals
there. I kept on snapping them off as well. What a headache that was. Now I'm making the actual
mounting rods. I've chopped the larger size rod and these ones I'll be actually adding to the
engine. Once they're both glued into place I'll then add the narrower rod. I'm just cutting two
lengths of that. And the whole idea of using this system is I can then slide it in and out
whenever I need to. Paint them, put them back in, take them out again.
I can twist them if I need to, to align them. And there you go. It makes life so much easier.
I'm loving the silhouette now. It's looking great. Really happy with that. And I thought
I'd better add some more detail to the actual rods. All the support struts.
And little things like this make a huge difference. Now after looking at this I kind
of thought okay I've got a bit of gap between the actual body and the engine, the rear engine. I
thought I might use some of my greeblies to fill it up. So I just went through my spare parts box
and had a bit of a look see what I could find. And some were too big. Some were too round.
Some were just horrid. This one actually was the bottom of another motorbike engine that I had
laying around for I guess the last 20 years. So I was really happy with that. So I needed to file
off the logos on the side. I think it said Honda on there. And that I thought looked really really
good. So as a matter of gluing into place. And then adding some of these little struts there.
And just checking to make sure I've still got clearance there. Got some. So now I'm just adding
some greeblies here and there. Again some more of those tank suspension bits. You can see all the
greeblies I've added. It looks really good. I kind of looked at it and I'm thinking hmm there's
something not quite right. What do I need to do here? Give me a bit of a think. Then I thought
I'll think about it later. So pulled out the black undercoat and giving all the bits and pieces a bit
of a spray. Once I start doing this base coat it ties everything together. Makes it look so much
better. Well we need to start adding a bit of a highlight to it. So I'm going to dry brush this
Tamiya metallic grey over it. And to do that I'm going to use some of these brushes that I picked
up from TK Maxx. $13. $13 Australian dollars. Cheap as. And we're going to give it a bit of a go.
It turns out these dry brushes, well these makeup brushes I'm using for dry brushing, actually
turned out to be great. Absolutely fantastic. Look at that. I think I need to go back and get a whole
bunch more for $13. Now after that all that thinking I've realized what I need to do is
actually add some more greeblies inside. It feels a bit empty in there still. So I went through my
past box and I came up with that little base item there. I thought I'll add a whole bunch of
greeblies to it. Of course I've painted that black and dry brushed it as well. And let's glue it into place.
And it makes a huge difference. There isn't such a void behind the engine. But I also thought what
I might do is just add a few hoses in there to connect that unit to the rest of the engine.
I'm just using this, I think it's 1.5mm wire. And just some random holes in the side and also
into the engine. And in retrospect I probably should have done these a little bit shorter.
But I kind of had this idea I might have them slightly hang down like they're
aftermarket hoses and they've kind of tried to do their best in what they had.
I like it, I don't mind it. Probably would I. And of course we've got to paint them black.
I'm just using the Vallejo black. Of course we've got to dry brush them.
Now I thought the front of it was a bit plain as well. So
I'm thinking I might put something that looks like sensors or something like that.
Just to add a bit of visual interest on there once again.
And that was just a headlight from one of the model kits.
And another something from something else. I'm happy with that. And also those holes on the side.
Now I've been umming and ahhing during the whole kit build. So I thought yeah I'll fill it up with
this styrene sheet. Now all I have to do is just mark it to size or roughly to size.
Scoring and snapping. That's one of the great things about this sheet styrene.
And what I'm doing is I'm putting it in there and pushing it quite firmly with my finger. So
it actually contours to the body shape. And then running some liquid glue through it.
And same thing on the other side. And also I did those little vent ones
on the left hand side of the fairing there. They're all filled in.
Now looking at the body of it. I thought it might need some more detail. So I've got these
little rivets there. Now these rivets come from the little diamond art things that little old
ladies do. I'm referring to my mother. A little hobby that they do. And she had thousands of
these left over. They've turned out to be great for use as rivets. So a bit of glue and a lot of
patience. Slowly went through the whole body fairing and added these rivets. Quite honestly
I was really happy with the way these rivets were looking. Maybe slightly too big but still
added a great interest to it. I think I might be adding rivets to everything now.
Since I've got thousands of them. And let's do the base coat for the body as well. We're
going with the black. I'll be doing three different coats of this. Starting off the black
and moving on to another few colors as we build up. Because I'll be weathering the kit.
And I'll be using a technique I've never done before. So I'll let you in on a little bit later.
And that's body fairing as well.
Now I'm using the steel. This is for the next coat and this is to show the metal.
The metal of the body. So when we do the weathering it actually basically wears through
with a sanding technique that I'll show you a little bit later. Nice even coat on all the body
parts including the top of the engine. And now for the rust layer we're using this red brown.
German red brown to be precise. Nice even coat as well. And now I'm going to use this technique
that I've never actually done before. Using some sea salt. Basically you just need to crush it
down and I did that with a small little hammer. So I had varying sizes and then you basically
brush the whole thing with some water and then sprinkle some salt on top. And that actually
well it kind of liquefies the salt and makes it stick to the body. That creates our rust pattern.
Now in retrospect and obviously because this is the first time I ever did this technique.
In retrospect I probably should have crushed it down even finer than what I did.
I'm just trying to add enough water so the salt actually dissolves.
Now once that's dry I grab the electric blue and we do the final top coat.
And just go over the all the body parts once again. This will be our final color.
Just making sure we get inside all the crevices of the salt and it's totally painted. Nice even coat.
Now while that's drying I'm grabbing this Soilworks oil wash. I'm just going to go over
the engine with it. Just add a bit of wear to it. Just randomly going around all the metal bits
and just adding this wash. At this stage I think I've broken off the foot pedals and
handlebars probably about four or five times each. And here we go it's time to get rid of
that salt. Now I'll just start off with just rubbing with my hand getting some of the bigger
pieces off. And then quite forcefully with a toothbrush try and get the rest of it off.
I'm really happy with the way that's come up. You can see it's already creating the texture.
Now I'm starting off the P1500 to do some of the wear and tears. But I ended up finding that
the 1500 grit is just way too fine. So I ended up changing it over to the 1000 grit
which gave me faster results. And you can see the silver section of it starting to show now.
And that looks like our metal layer of the tank or the body fairing things like that.
It's time to glue the tank onto the body. Now I'm using aerodite here because the tank actually
doesn't sit completely down. So I need to actually use the aerodite and then push it down onto the
tank so it holds better. And then five minutes later it's all good. Now of course we need to
do the metal parts of the engine. And I'm dry brushing it with this Ammo dry brushing paint.
And that's a gunmetal color. Now to glue on the seat which was sprayed with just flat black.
And some hot stick for the rear fins. Now for some reason I decided I was going to add a bit
more weathering. I decided to use this streaking grime and I think I kind of overdid it here.
I put too much of it. In retrospect it was just it just probably didn't even need this
layer at all. And if it did just some a tenth of what I actually used. It was just way too heavy.
It doesn't look too bad it's just in like I said in retrospect in hindsight when you look back it's
just yeah probably didn't need it. Of course the windscreen which I almost totally forgot about.
So we're just going to place it into position. Just add a couple dots of this fine Tamiya.
And I'm giving the whole windscreen a wash with white. And it's really really thinned down with
water. And it's actually white gray from Vallejo. Once that's dry I'm going to add the final pieces
which is these hydraulic hoses that came with the original Kawasaki kit. I didn't use all of
them I just used for the handlebars and a couple sections on the engine. That's all I need to do.
And I was you know overall I was very very happy with the way this hover bike turned out.
I learned a lot first time I ever done this salt chipping technique. I'm just using the hair dryer
to soften up the hoses here so I can maneuver them better and shape them to where I need it.
So once they cool down they they held in nicely. A lot of things I've learned. I'll probably do
another one very shortly because I really enjoyed this build. And now I think it's time for the hero shots.
