Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back with another
cool arcade game repair video for you
today one of the games we have here in
our shop is this Atari Sprint 2 classic
classic 70s black and white video game
uh we got this in and uh
it had a problem with it that a lot of
these have now we're obviously still
working on it it's filthy and all messed
up but right here in the middle of
repairing it we felt we figured we'd
film this video for you because this
could apply to other games as well maybe
it'll help some people out
look at that big hole in the side of the
game whenever we got it uh someone had
vandalized it so they've broken into it
they had uh stolen even the cord off of
it right so we did a video on it already
if you want to see us repairing it and
how we got the back up and running uh go
back and watch that video it is here on
our Channel and it was the video that we
uploaded just two days ago so if you
look on our channel uh chronologically
we upload them in order right
but we still got a lot of work to do on
this but what we're up to now is the
steering so the steering is a problem on
this game and a lot of Atari games so
what is the problem it's this steering
assembly that they designed now this is
just hanging on here so I got to be
careful but this thing is all loose see
how the wheel is moving
that's because this plastic piece right
here
um
is completely destroyed you see how
cracked up all that is
so that is a big like a conical piece
that goes in there that a board mounts
to
to sense the steering and then there is
this shaft that goes down through the
center of it inside of that and there's
a couple
um
uh bushings one at the top one at the
bottom and all this stuff so there's an
assembly I'll show you the drawing of it
here in a minute but basically this
piece here has been a problem for a long
time so it's it's not just on this game
it was used on
Sprint this is Sprint too it was used on
Super Sprint which is the one with three
players it was used on uh
Championship Sprint
which is the one with the that was a
little lighter the system 2 game I
believe it is it was used on all points
bulletin
uh and several other ones it was it was
used on several of the 70s black and
white games like I think it was used on
Trek and some other some of the other
ones
uh so if you've got an Atari steering
game it very well may have this same
setup on it now if you've got Pole
Position
it doesn't bolt position is different so
the most popular Atari game doesn't use
this but a lot of the other ones do all
of the sprint series pretty much uses it
um
so what what has been you know people
have been fixing these for decades now
you know most of these this one came out
in 76 and then there were a bunch of uh
Atari Sprint games in the 80s that were
a big deal and everything so come along
you know the 90s people were started
getting these in their houses that they
bought from old operators and stuff and
they would fix this part now one of the
ways they would fix it or the main way
that they would fix it is you would try
to find
one to replace it with right and so you
could get another used one that wasn't
quite cracked this badly or you could uh
try to find a New Old Stock one so there
was a supply of New Old Stock housings
and it's about four inches down in there
you'll see it all here in a minute
um
so it's a significant little piece but
it you know it's not the end of the
world there was a supply of those New
Old Stock that people were selling for
years and it's finally kind of dried up
so the price on those just kept going up
and up and up and we're kind of the
point where you can't really find a New
Old Stock one anymore
and you can't find one that isn't all
busted up right if it's decent people
have it on their on their game and you
can see that the wheel doesn't really
it's all screwed up right
so we need to we need to get that better
this one is no better really it's a
little better but it's
you see the crack down there
right now on this particular game Sprint
too this is the one player side and
that's two player side now how do they
get broke well I don't know it could be
vandalism this thing's been abused uh
but it's probably just that they got old
and they get brittle over time they just
break it could be it was a bad design
idea but it shouldn't have been done
like that in the first place right which
uh the fact that they changed it on pole
positions might suggest that but if you
think about it Pole Position was a Namco
game not a notary game
and uh also
um
uh Atari made Championship Sprint after
pole position and used this older
setup you know
so I don't know who knows but a lot of
them are broke so if you've got one of
those games you very well may have one
of those things broke well guess what we
have found a solution so what I did was
I contacted some people and asked them
hey let's see if we can 3D print one of
these so a gentleman had a friend that
had one he was able to get that piece uh
uh make a model of it and he has made a
prototype that he has mailed us
so in this video we're going to test out
the Prototype that was 3D printed to see
if it can save this old beautiful game
if it can we're going to have him make
us two brand new ones
um we're going to install them on the
game and that'll be that but he's going
to offer them for sale for anybody that
needs these in the future he's got some
other parts that he's make that he's
made in the past and he's made some more
Atari reproductions too so it'll kind of
be a good fit so um
we're going to take this control panel
off clean it up and uh let me let me
show you in the manual a little better
uh view there's an exploded view in one
of the manuals that shows you how the
steering wheel is put together what the
parts look like and uh the part that's
given us all the trouble then we'll take
this one apart put the the prototype in
so we can freaking test it and give him
some feedback if anything needs to be
changed we think it's a pretty good
Proto Proto already he's thinking about
doing a couple things to strengthen it
up just so that we don't get problems
and down the road
and we're basically helping him develop
this product that will be available to
sell for people that need one for their
machine so uh let's check out the manual
for a minute and then we'll get to the
control panel
okay so here is the manual this is uh
the Sprint 2 manual doesn't show
the details on the steering wheel but
this is from track 10 Trak 10.
track 10 which was a similar key games
uh game from
back in the day
so this is the back view of the
steering wheel we're gonna I'm gonna
we're gonna show you all of this here in
person here in a second
uh so you're looking at the back of it
there is a
encoding wheel that goes through these
little Optics here or actually it's here
and there are six screws that hold it on
and then here is the side view so we
have the steering wheel
there's a long bolt that goes all the
way through and attaches on the has a
nut on the back
and this housing here is the part that's
cracked
so you know a lot of this lip is broke
that attaches it to the
front of the uh of the game you can see
there's just a little bit of a lip that
holds it
and so the wheel and the shaft spin
inside of this thing
and this little encoding wheel runs
through the optic on the back
and that's how the thing works
so there are there are two little
bearings too there's one right here and
there's one here it's just a little
nylon piece of plastic or a little nylon
piece of nylon uh that's called a
Thompson nyliner
and um
that kind of holds everything in place
and gives it a little just a little
bearing and then there's a little bit of
grease in there too
so down here it has the actual part
numbers
okay and you see there where the housing
is zero zero six zero five that's the
part that's messed up okay now if you
look let's go forward
10 years
the championship Sprint
Championship Sprint very popular game
it's pretty much the same setup
steering wheel this little
um uh shaft here it looks a little
different
but there's the same exact bearing the
same exact housing
the other little bearing and then the
the little board on the back is slightly
different
but not a bunch different
it's just like the connector basically
is different
and then there is the encoder Hub there
is the same and the lock washer and the
bolt
this actually has a bolt that goes in
the back so it's made just slightly
different there's there's basically two
designs but they use the same housing so
if you uh
somewhere here they actually show the
part numbers for that let's see if we
can find it
we're going through
don't get dizzy
we're trying to go to the
to the parts list
yeah hello parts list
here we go
there are two exploded views of the same
manual
uh look at that zero zero six zero five
it's the exact same part now it says
Dash zero one there must have been a
maybe it's a slightly different revision
or something I think they just upgraded
their part numbers personally
right so that's the piece that breaks
that little that little
bezel around it chips away and then you
are in trouble
here's an old chipped up one so you can
see kind of how the housing looks after
it's all broke up
okay so I'm gonna throw it over to Joe
he's going to start working on the
control panel and tell you what he's
doing and see how nice we can make the
thing um
and then we'll come back we'll show you
where you can get the uh the housing
from if you need one
all right I'm gonna try to clean up this
control panel
we've got a guy that 3D printed us a
couple of these grommets
they break on all these Atari racing
games
so I'm basically going to take
everything off of it I'm going to try to
clean up this aluminum
I may repaint some of this black
and just see what happens hopefully I
can get it cleaned up a little bit I got
to take a Brillo pad to these steering
wheels try to get some of that rust off
there
[Music]
foreign
[Music]
[Music]
thank you
[Music]
foreign
[Music]
thank you
[Music]
[Music]
thank you
[Music]
foreign
[Music]
foreign
[Music]
[Music]
foreign
[Music]
[Music]
[Music]
foreign
[Music]
foreign
[Music]
[Music]
[Music]
foreign
[Music]
[Music]
foreign
[Music]
[Music]
foreign
[Music]
[Music]
foreign
[Music]
[Music]
foreign
[Music]
foreign
[Music]
foreign
[Music]
[Music]
foreign foreign
[Music]
foreign
[Music]
foreign
[Music]
thank you
foreign
[Music]
thank you
[Music]
thank you
[Music]
thank you
[Music]
foreign
[Music]
foreign
[Music]
foreign
[Music]
[Applause]
foreign
[Applause]
[Music]
[Applause]
[Music]
folks we got the Prototype installed and
everything's cool but unfortunately I
think it's just a little bit too tight
but that's what we got a prototype for
it works you can play it but if you the
problem is
let's select if I set it like that
foreign
it's just a little too tight it's not
quite right
and since this is the same piece that's
in Championship Sprint that's one
particular game where the thing is
supposed to spin around pretty well
right
so um we're having him double check some
stuff and he I think he's going to make
it just a little bit
uh with a little bit more room in there
to
fit the bushing a little better and uh
he's also adding some steel studs in the
in the next one so on the next version
it looks like it's going to be just a
little have a little bit more
play in it and have those steel bushings
so we'll wait for that and whenever we
get it in we will uh check it out
okay folks we have got we believe the
next stage prototype this may be the
final product so
differences
added plastic I mean a metal studs
inserts
what do you call those what are those
called Joe
huh
he says they're called inserts I can't
remember the name of them but there's a
specific name for those
so the purpose of that is those
shoulders are what usually break on the
game because they use bolts that
basically have a thread in it that just
eat into the the original stuff okay now
these are interesting here
these are bearings but he is actually 3D
printed some bearings so we're going to
see if they're smooth enough though
because you know when you 3D print
something it has a little bit of a
texture to it so we're going to see if
they are
uh smooth enough to actually work
there's even a king
a key in it
for this slot
those are very thin but that's not
supposed to be
okay and then there's one on the front
as well
I was noticing earlier look how it
prints this kind of suede look on the
front that's kind of cool
so we're going to uh we're going to
install this this is was made out of
cardboard originally but he's offering
these now as well
it's basically a 3D printed part I don't
know where that went though to be honest
I think maybe it went behind it
um
so we'll see
but we're going to we're going to mount
that in and see if it's a little bit
better fit on the wheel the wheel has a
little more
give so it can spin a little easier
and we'll see what it looks like okay
folks so here's an original one
and you can see they get all cracked up
screwed up and these are the original
screws that just threaded into the
plastic
okay so here is the Prototype
you can see that he's he's uh
that made some of it a little thicker
trying to improve the product a little
bit
we thought it was just a little bit
tight here is the new one
even with the new bearing he's put the
little catches in it to catch the bolt
and these of course are still thicker so
we're going to test it out here's the
basically the production model next to
the original
very cool liking it a lot let's try it
out
foreign
[Music]
check that out
very cool
and the spin test are you ready
that's kind of how I remember it it was
something like that
and then we have the second one in for
over here this wheel is a little warped
a little bit but uh
works just as great
fantastic
so if you need that for your game you
may have a Sprint one you may have a
Sprint too
you may have a uh Super Sprint a
championship Sprint at all points
bulletin
you might have a track 10 a track 20.
a superbug
there's a lot of them folks
so if you need one let me show you where
you can get one
okay so if you'd like to get one there's
a gentleman at arcade plastics.com
he's a old school arcade guy has a whole
bunch of games himself works on them a
lot and has been printing out uh some
little
things that you end up needing like
little pieces for joysticks and things
like that
and he decided to go ahead and make the
Mount and we've tested it and it works
great
so there are the two
bearings the
piece that was originally cardboard or
something I think that's some kind of
spill guard or something it just wasn't
on our machine but I think on the newer
ones that's on it uh some bolts and the
actual housing with the inserts in it
and everything fits right in your
machine
says this kit works for games such as
Championship Sprint one Sprint two
Sprint four Super Sprint drag race Super
Bug
this is a drop in replacement for the
existing steering wheel mount
and check this out you can get all
different colors this black red blue you
can get red and blue which would
probably be really nice on Championship
Sprint
a green yellow yellow might be nice on
superbug
very cool
um so it includes the housing there's
the part number the Thompson bearing the
Thompson bearing the cardboard ring
replacement that he made out of plastic
and the six hex head bolts to pop in
works pretty good he says he can do pink
too
all right free shipping in the U.S this
is a steal we tried to get them to make
the price more for you
just kidding
but he's able to do these pretty
affordably so forty dollars and you get
all that stuff with free shipping can
you believe that
I'm sure the price will have to go up
how he's able even able to cover his
expenses with that I have no clue
but uh very cool so he's uh working on
some other plastic things and 3D
printing them and it's working great
it's a great example of using new
technology to solve an old problem right
I guess the original ones they had a
mold and they were injection molded or
something
but um yeah so there you go so if you
need one of those the New Old Stock ones
seem to have dried up they can't be
found
and if they are found they're very
expensive so here's your opportunity to
get yours working good looking good
for a fraction of the cost
awesome to see somebody making brand new
parts
for a 46 year old game that's pretty
cool
so there you go folks I hope you enjoyed
it check out arcadeplastics.com we're
going to do another video we still have
to do some cosmetic stuff on these on
this uh machine Joey made the control
panel look really nice Inked it in and
by the way that was acrylic paint we
were using on that that's not a Sharpie
if you use a Sharpie whenever you clear
it it'll run all over the place
don't do it not even once don't try it
so you want to use acrylic paint if you
can so um you can get acrylic paint in a
little paint pen now some of the stuff
we use whenever we uh do repairs like
stuff like just little ink pins and
stuff like that you can get on our
website to go to lions arcade.com and
there's a parts page at the top normal
Parts page
there is a link to a bunch of things on
Amazon that we use in our in our videos
so if you click on one of those links on
lions arcade.com it takes you to Amazon
anything you buy on Amazon we get a
little piece of if you buy this
gentleman's Hub we don't get paid
anything for it the guy just uh happened
to be making one right whenever we
needed one and so we were able to test
his uh prototype and all of that and
he's not paying us to do this video or
anything we just figured we'd tell you
about
a great product so go check it out and
check out our website to lions
arcade.com and that's that so we will do
another video where we finish up the
Cosmetics we've got to do something
about that big huge hole in the side of
the cabinet people
did you see that thing
there's a hole kicked in the side of the
cabinet looks like they went nuts on it
with a hammer
trying to get at the quarters
the quarters are gone but the hole's
still there so I got to try to fix it
it's the size of a basketball
not cool so uh that will be on our next
video so I hope you enjoyed it make sure
to give us a thumbs up for taking the
trouble to film it for you and by the
way don't forget to check out my brother
Donnie my brother has his own
channel here on YouTube
and uh we work on arcade games pinball
machines jukeboxes things like that my
brother Donnie works on buildings homes
lately we've been doing a mobile home
that's pretty cool uh and uh old
Vehicles things like that so we will see
you over there on his channel and we'll
see you back on the next video where we
uh do some painting