How to scarf plywood using a router - Building Gannet - Episode 6

Nomad Boatbuilding
98 followers
Feb 17, 2025
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
[Music]
welcome to snow my boat building I'm
Mark Ruden and today I'm building ganet
we're going to scarf some plywood
scarfing is a fundamental technique that
you really have to learn if you're going
to get involved in boat building we use
it all the time more often than not you
cannot get stock that's the full length
of your boat and so you need to be able
to make that stock up through the
process of scarfing there's a bunch of
different scarf configurations you can
use nib scarves keyed scarves things
like that but the standard flat scarf
will take care of 99% of all of your
needs in wooden boat building if you're
building a boat out of plywood you
probably going to use scarf joints to
make that planking stock the full length
of your boat now when I'm doing my prep
work for a build scarfing that plywood
to full length is not something I do
early on that's something I hold off on
doing until the last possible moment and
that's just because I don't have the
room in the shop to necessarily store a
bunch of scarfed plywood I virtually
never scarf full width sheets of plywood
there aren't that many types of boats
that I build that require that kind of
width and even if it's more efficient to
have a full width of plywood scarfed for
the purposes of getting planking stock
out of it I simply don't have the space
to have that bigger sheet of plywood
hanging around in order for me to work
with so I will always make my plywood
narrower in this case I'm going to cut
my plywood in half so I've got twoot
wide sections in many cases I'll just
cut my plywood down to like 8 in widths
and get my planks out of that using
short sections and scarf the plywood as
I need it or scarf it on the boat that's
especially helpful if you're building a
really long boat with particularly
narrow planks cuz once those are full
length and cut down to their finished
width of we'll say 3 or 4 in or
something like that for instance a long
narrow canoe that can be really unwieldy
especially if you're working alone my
boat's only 14 ft long so I'm going to
pr- scarf my Plywood And pre-glue it and
I'm going to have it all sitting on my
planking bench there so I think going to
use my strong back to do my glue up
because I'm going to be able to get
clamps on both sides of those sheets so
that's going to be make it really easy
to do the clamping I very rarely try to
cut full sheets of plywood on my table
saw the low ceilings make it really
awkward to maneuver sheets around so I
find it easier to just do it all with a
circular saw I have this light frame
made out of 1x4s it's basically a
sacrificial platform on which I do all
my circular saw cutting and sometimes I
use it for painting as well
so the number one thing we need to think
about when we're scarfing is the scarf
ratio that's the length of the slope in
the scarf now the bare minimum I ever
use is a 6:1 scarf and I usually only
use that in Plywood And primarily I use
that in light plywood I'll explain why
in a moment on average I use a 12:1
scarf for almost everything well 12:1
scarf represents a lot more surface that
you need to clean up and flatten out I
find it's actually easier to fit and in
theory when you bend a piece of planking
that's got a longer scarf in it it's
going to bend more fairly whereas if
it's got a short scarf it might show a
little hard spot where that scarf is if
you're cting a scarf for material in a
spar for instance you might go much
longer like a 20 to1 scarf we want The
Spar to bend smoothly we don't want a
hard spot at the end of a scarf joint
and so a long 20 to1 scarf is going to
be have a much smoother Bend to it but
today we're talking about scarfing
plywood now here's the thing I find that
the act of putting a scarf joint into a
piece of plywood actually stiffens it up
in the area of that scarf and so for
that reason what I found is when you do
a long scarf in light plywood say a 12
to1 scarf you'll introduce kind of a
flat spot if you bend that plywood a
fair bit especially in light planking
now this planking is 38 when I check and
see how the area of a scarf reacts when
I bend the material it's pretty fair so
I'm confident a 12:1 is going to be just
fine however if it were light planking
like/ qu in or 3/16 I'm pretty sure I'm
going to notice more of a flat spot over
a long scarf and so for that reason in
light planking I will tend to lean
towards a shorter scarf if the planking
is going to be taking a hard bend around
something if it's a mild bend over a
fairly flat section of
body I'm going to go with the longer
scarf regardless because I am set up to
cut those and I just find them easier to
work with back to what I was saying in
the first place a 6:1 I'd say is a bare
minimum scarf and I've used that
throughout most of my career and it's
only recently I've started to do longer
12 to1 scarves either one's going to
work just fine however if you're going
to glue up that scarf with an adhesive
that isn't Gap filling like epoxy I
would go for the longer scarf because
it's got more face grain and you're
going to have a more reliable joint so
this is a simple scarfing jig that I use
just for doing plywood a board in here
that raises the ply up a little bit so
that I can get the feather edge done on
the last sheet of plywood I've got my
scarf ratio built into these sides here
it's a 12:1 scarf and I just have to set
my plywood up here staggered at the same
ratio in terms of scarf length so I've
made up a little
pattern that I use for stepping these
sheets of plywood
backwards and by doing this you can just
cut the ramp all in one shot for some
reason before you can hit the line on
the lower sheet you'll start eating into
the f edge of the one above it so I all
stop short of that and I finish off the
last little bit by hand it's really not
a ton of work so I don't really mind
doing that the ramp here takes care of
so much of the effort now I could do
this with a power plane that's how a lot
of people do it I really hate using
power planes for this sort of thing I
just find them really obnoxious the
router does a cleaner faster job I think
and there's also jigs that you can use
with your circular saw to cut the scarf
in one Edge although the average
circular saw doesn't have a blade depth
that allows you to cut more than say a
Quin sheet of plywood this is 38 so even
if I tried that my my saw curve would
stop short of the finished ramp so it
really doesn't make a lot of sense to
try and use that so on top of this we
have just this simple sled that my rotor
sits into and I've tacked all these
sheets down using my Polymer nailer so
that I don't have to worry about it
being clamped down here at the feather
edge it helps to hold it all down nicely
of course I've got the planking stock
clamped down right behind The Jig and
I've got the plywood ramped up onto some
stuff that sort of keeps that feather
the feather edges down so we don't want
the back end drooping down because it's
going to want to make these pop up we
don't want that I've got a nice big
chunky bit on the rotor
here just drop it into the sled I'm
going to I've got it set for almost the
finished depth so I'm just going to back
off on that by a couple
turns and I'm going to slowly plane the
material off of here going in one big
pass all the way down to the bottom and
then I'll dial it down a little bit and
do a finish pass now this makes quite a
bit of dust so I'm going to get the fans
going and get my dust collector going
try and pick up as much dust as I can
while I'm
working despite all the effort required
to make a jig I think this is much much
faster than trying to use the power PL
if nothing else it gets me much more
consistent results now I'm at a bit of a
loss as to why I cannot get the full
face of the scarf planed off I think
it's just the mechanics of how sheets
can lie against each other there's just
that little microscopic bit of
separation between one sheet and the
next that shows up in the final result I
find it simpler to not worry about that
playing it down till I'm almost to my
feather edge and then finish it all up
by hand I've also tried doing this by
setting the rotor for a very light cut
and then proceeding slowly taking
increasingly deeper Cuts but I found it
simpler just to set it for almost a full
depth and just proceed slowly with my
passes rather than cover the ground many
many times
over the greatest danger is as you eat
into the final veneer if your cut is too
aggressive you'll tend to chew up the
edge of that plywood and leave it all
raggedy but there's actually a pretty
simple trick of fixing that when you to
get down to the final shaping you just
need to PL back that feather edge of
hair and lengthen your scarf by the same
amount you've planed it back and just
tune it all up by hand that's really not
that much extra
work here's an example of when I tried
to set the router to its full depth and
it really chewed up the feather edges of
those planks so that's why I stopped
short if you're liking these videos you
can support me by giving me a thumbs up
throw me a couple of bucks through super
thanks subscribing to the channel
turning on notifications and of course
you can join me over on patreon find
links in the corner or down in the
description I've roded until my final
pass leaves the last veneer about
halfway cut through you can see how much
narrower that last band is on each sheet
so I'm going to use a belt sander here
just to try and bring it down a little
bit closer now I'm not going to get it
all the way but I'll get it till those
feather edges are just about finished
finished and you can see in this shot
how those feather edges rise up a little
bit you can see those dark lines of
separation between the sheets and this
is why you can't seem to get the feather
edge done perfectly while reaching the
termination of the scarf ratio at the
other
end and now using a sharp hand plane I'm
just going to tune up those scarves so
the feather edge I'm trying to make sure
it's nice and thin that it's actually a
feather edge and then I'm taking the
rest of the scarf back to the the layout
line now I'm only going to work on one
sheet at a time despite the fact that
they're all stacked up here just like
with the belt sander my plane isn't able
to get down to the shoulder on the next
sheet anyway because the mechanics of
how the sheets lie together that said
there's no reason you can't take a skim
over the whole thing with a hand plane
and try and get it all a little bit
closer when I feel I've gotten close
I'll often switch to a smaller plane and
just try and make sure that I've got the
middle of that scarf nice and flat or
even hollowed out a bit and of course a
sanding stick like this is a good way to
go for that too we want a nice roughed
up surface for the glue to hang on to
something around the 80 grit range works
really really well now before popping
one sheet off and starting on the next
one I just want to Mark where the
shoulder of that scarf is and then using
whatever I have lying around as a
straight edge we'll just Mark that line
all the way across and then we're ready
to start breaking this down and start
working on the individual
sheets now of course I just repeat this
fine-tuning process until all the sheets
are done and then we're ready for a glue
up so I like using these Little Dixie
cups from doing my mixing in so I don't
need a big huge cup now I know I'm gonna
need at least two shots for each seam on
this
boat so we'll just start with
that I always pump my resin first then
my hardener one one one one always cuz
it's easy to lose count you'd be
surprised okay and then
we have a mixing wand on my drill
here you wouldn't want to do this for
for doing a wet out of fiberglass cloth
where you want it to be clear but this
is great for doing anything that is just
uh structural just speeds up the mixing
time a
[Music]
lot and now with everything organized
we're ready for our glue up we also use
proper gluing procedures by wetting out
our surfaces especially when we have a
lot of open grain like we do in a scarf
in plywood lots of end grain there
basically so you really want to make
sure you get those coated with
unthickened epoxy before you add
thickened stuff if you don't do that you
risk starving The Joint of the glue and
you end up with a weak
joint I usually mix my epoxy in more
than one batch so I'll mix up a batch
that I think is enough to do all the wet
out and I'll go and mix up another batch
to do the thickened epoxy now there's
only a couple of shots that are required
for the whole glue up I won't bother
with that but when there's more than
that I find it simpler to do it in
smaller batches that allows me to gauge
the overall volume that I'm going to
need more accurately and it also means
that once I get to the final stages of
the glue up I've got the maximum amount
of working
time now I'm using wood flour to thicken
this particular batch of a pock oxy now
you can use sawdust out of your sander I
actually collect mine out of the final
stages of my desk collector the stuff
that's stuck to the filter
itself but you do need to run it through
a fine strainer in order to get rid of
any chunky bits you really want this to
be almost like dust wood flower not only
adds body to it but it adds a fibrous
element to it that helps to create a
stronger Bond and if you get the color
of the sawdust right it will actually
help to hide that joint in the finished
product usually the sawdust you need is
a little lighter in color than the
species of wood that you using because
once it's mixed with the epoxy it comes
out darker we only need to add the
thickened epoxy to one side of the scarf
so long as you've wet it out both sides
it's going to work
fine if my Knuckles here represent the
line that we're trying to glue
to we always want to pull back from that
just a little bit like an eighth of an
inch
maybe that's to make sure that there's
enough room in the scarf for glue to
take up without the joint being proud so
if we went right to the line guaranteed
one side would end up being a little too
proud you end up sanding through your
veneers to flatten it out so you got to
pull back just a little tiny
bit I put these posts on the strong back
here to butt all the planks up against
and that was just to or Orient the the
planks together so I got them nice and
straight and I don't have to think about
if they're cocked or anything like
that and now to clamp all this down and
just apply enough pressure to get a
little squeeze out on this joint so
these clamping calls are uh big chunks
of Ash they're 2 in thick by 3 in wide
and there's there's a slight curve in
them it's maybe uh I don't know they
rise up maybe 38 what is it just about a
quarter of an inch at the ends I kind of
think maybe it could be a bit more for
for putting greater pressure on there
but you don't want to make it so great
that you risk um pushing a bow into the
thing that you're trying to clamp but
anyhow so they work pretty good I've
used three of them to try and get
maximize the pressure in the middle of
the
panel and I've
bridged that the whole thing with a big
piece of 1 in MDF and that's just to try
and even out the pressure over the whole
thing so it's like one big clamping
force a little extra oomph from the
clamps coming down from the ceiling
right in the middle of the board so
fingers crossed I got a good glue up
it's always a little
bit worrisome when you try and glue up a
lot of panels at once because you need a
lot more pressure to try and get them
all to flatten out so I think I did okay
I kept my epoxy a little wetter than I
would if I were just doing a single
plank glue up and that's because I need
to make sure it can squish down
nicely all right we got our planking
stock glued up I wanted to take
advantage of doing this now because I
have the strong Back available to me as
a working surface a good level flat
working surface so I put some plywood
down in the center where I'm doing the
glue up in order to give myself solid
backing for this being able to get
clamps onto both sides of this glue up
was really helpful compared to working
on the bench now if you can't get clamps
on you can always use screws and just
screw all the plywood together with some
plywood backing and plastic in order to
keep it from bonding of course and you
can repair the screw holes later on that
is a really common technique I don't
really like doing that but you could
certainly do that now I should point out
you do not have to use epoxy to scarf
necessarily epoxy is a great material
for scarfing because it fills voids
really easily and epoxy likes itself it
prefers a joint where there's lots of
epoxy in it as opposed to a joint that's
very very tight so uh for us in boat
building that that we that has a a a lot
of good practical um qualities to it but
if epoxy's a problem for you if the
expense is too high if you have an
allergic sensitivity to epoxy which a
lot of people do you can certainly use
other adhesives um there's polyurethanes
on the market both in a cocking tube
form and a uh a liquid foaming form you
could certainly use those there's the
old-fashioned stuff which is plastic
resin glue which is kind of a urea from
alahh high glue that you mix a powder
with water that works really well and
it's actually a great glue for doing
laminating and stuff like this and then
there's products like tight Bond 3 which
is like a PVA style glue which is a
really good waterproof glue it's as good
as a as aoxy if not better it just
requires a more accurate joint that's
all and the same rules apply about
starving The Joint even if you're using
a PVA glue it's a really good idea to
coat both surfaces give it a minute for
that glue to soak in a little bit make
sure that you've got an adequate volume
of glue before you start clamping as
we're planking the boat and your your
working from a wider bunch of planking
stock that's preglued you're you're
trying to Nest all those planks close
together to maximize the use of the
material and I'm always a little worried
that it's wasteful and that I won't get
all the material I need out of preglued
planking stock it's a just a a hangup I
have so I tend to prefer to pre-cut all
my stock down into narrower widths and
then figure out what angle I need to
glue up to get any particular plank out
I kind in some ways I kind of wish I'd
done it that way here I've done that in
the past but it requires sort of a
almost like a two-stage process of
spiling for the plank and then figuring
out what the plank Arrangement needs to
be either scarfing or pre-cutting and
then
gluing in place and then waiting before
you can hang the plank which feels um
there's an efficiency to it but there's
an inefficiency to it too and I can't I
can't compare apples to apples and in
order to figure out which is the most
advantageous method all right let's
break this apart hopefully we got a good
squeeze out uh without it being too
messy all right let's see how this
turned out what we're hoping for is that
we've got enough squeeze out that it's
filled the little gap between the
feather edge of the scarf on one sheet
and the shoulder on the other but not so
much squeeze out that we've got a ton of
cleanup to do the biggest issue with
trying to do a cleanup is if you try to
use a sander to remove all the excess
epoxy
it's very easy for that sander to abaid
the plywood that is uncoated faster than
the thickened epoxy portion and so you
could end up creating sort of a dip in
the plywood around the scarf which is
unfortunate the best way to avoid that
is to use a heat gun and a scraper to
get off as much of the bulk of the
excess epoxy as possible
nice that looks pretty good that looks
pretty good we have some cleanup to do
obviously we always do but I'm happy
with that
let's just hope all the other panels
look like they got the same kind of
squeeze out okay folks this is one way
to scarf and it's by no means the only
way to scarf it's the way that is
working for me at the moment I find the
time spent making The Jig to scarf with
a router to be well invested Because the
actual scarfing process is much much
faster and it's a jig that I'm going to
use repeatedly that might not be the
best for you and throughout most of my
career I have cut all of my scarf joints
by hand with a hand plane no power
whatsoever and it's just fine it just
takes a little bit longer I want to
thank you all for watching and I hope
you'll join me again and if you can help
me out over on patreon I really
appreciate that you find links in the
corner or down in the description keep
your stick on the ice folks
