Lecture 3 -Introduction of MOS and Energy Band Diagram - II

IIT Roorkee July 201
61 followers
Jan 3, 2025
[Music]
[Music]
hello everybody and welcome to the nptl
online certification course ON
Semiconductor device es for Next
Generation Field Effect
transistors uh physics perspective this
is lecture number three in the series of
this course and we will be today dealing
with energy band diagram part two and
introduction to M
devices so we have learned in our uh
previous
discussions uh that the effective the
the thickness of the oxide layer right
the oxide across the oxide the potential
drop is given as minus q0 Prime by coox
Prime where q0 Prime is the charge per
unit area and CX Prim is capacitance
oxide capacitance per unit area and this
was the potential drop across the oxide
layer which we were expected to
see now uh so so so typically therefore
you have two components which we have
studied till now one is your F Ms which
is the metal semiconductor work function
difference and we will also have another
component which is this one minus q0
Prime by C Prime so if you want to add
these two together what I get is I get
flatband voltage vfb is defined as 5 of
Ms minus q0 Prime by coox
Prime right so the first component on
the right hand side is primarily because
of the difference in the Quant potential
between metal and semiconductor and the
second one is primarily due to the
parasitic effects of uh three or four
types of charges which are sitting
inside the oxide layer right and they
tend to uh sort of degrade your flatband
voltage so what what will happen
therefore is that an external voltage
source vfb has to be given so that you
reach the flat band right that's the
basic idea which we look into now now
let's come to the understanding of what
are the the various so when you go from
gate to the substrate what potentials do
you encounter and which of the
potentials will change if you apply a
bias so let's study that and then we
will go for the next stage of uh
learning so let's let's look at in this
manner that if we do uh so there are so
if you look at U let me draw a diagram
for you and let me show it to you that
let us suppose I have this MOS device
structure here and this is my metal here
and then I have an oxide layer followed
by semiconductor so this is the
semiconductor bulk which I'm talking
about and I have these positive charges
let us suppose being inculcated near the
oxide layer and there are positive
charges in boxes shown as straps which
are inculcated near the Silicon silicon
dioxide
interface right we will go one by one
and explain to you how these uh diagrams
or how these are important to us so what
we do we have this gate M terminal here
we have this bulk terminal here and we
just connect these two together through
a gate to bulk potential vgb let me name
it as
vgb right and so this is your gate
charge qg let us suppose right and you
will have here the oxide trap charges
this is q0 prime right and there will be
also the charge here QC which is
basically the channel charge now if you
take this into consideration and write
down an expression I can write down vgb
which is gate to bulk can be written as
sco the the drop across the oxide layer
plus the surface potential plus the
FMS right where sco is the oxide so this
this this is the drop across the oxide
layer CS is the potential at this
particular point and 5ms is because of
the metal work function difference you
will have a 5ms plot now with this basic
back ground which basically solves the
kov law only if I try to plot
here uh the value of this so this so
please understand on the on the x axis
you have potential right and on this
axis you have the dimension which is
this Dimension y Dimension which you see
so uh let me go one by one and explain
to you this is my bulk here right this
is my bulk so this is bulk is either P
type semiconductor and N type
semiconductor and this bulk uh will give
rise to uh your constant uh voltages
obviously because bulk is let us suppose
given a negative potential and therefore
the potential will be very very small at
this thing almost constant suddenly as
you leave the bulk you will actually see
a certain rise in the potential why
because now as you move up obviously the
potential will go on Rising because the
gate potential has been given a larger
value as compared to the bulk potential
and therefore this will rise and then
suddenly what happens is that there will
be a sudden increase in the voltage here
right almost a big drop now from so let
me let me uh let me change it so this
till this much point you will have you
will see a extension which you will see
till the interface oxide interface right
oxide semiconductor interface after this
uh if you follow this curve here right
then this will be almost like this so
across the oxide layer there will be
some potential drop which will be equals
to the oxide layer so this uh and and
and this is what the potential V with
respect to Y if this direction is y then
s of Y is the variation of potential As
you move from the bulk toward the
semiconductor right and this uh this
potential which you see here this
potential right this potential which you
see here because once it reaches the
edge it will again go on Rising why
because it sees a metal at the top right
and therefore we Define this to be as my
vgb gate to bulk this is my gate to bulk
so this all gate to bulk is now being
divided into three parts the first part
is basically my so let me draw from here
one line this is your s this is your
surface potential s of s then this from
here to here is your s of ox right and
this is your
FMS metal work function difference you
understand so this is your metal work
function difference the minimum of it
and then you have the surface potential
and then you have the oxide potential
the drop across the oxide layer is been
shown here so I get vgb equals to cs sco
plus S Plus 5 Ms right that is what you
get now let us suppose I make a change I
make a change in the value of vgb which
means that I give a Delta vgb change so
let me do that and show it to you so I
get the Delta vgb change here this will
be Delta scox plus Delta sis and you can
understand the reason why the reason is
any gate voltage change which you make
gate to bulk voltage change which you
make will finally get reflected onto the
change in the oxide and the surface
potential because FMS is almost constant
because once you have fixed the metal
and the semiconductor the FMS value
depends only on the contact potential of
these two so basically I can safely say
that my D of 5 Ms D of 5 Ms Right is
always equals to zero there will be no
change once you have fixed the metal
once you have fixed the metal and the
semiconductor once you have done that
there will be no change so any gate
voltage change will be accommodated by
the change in the oxide and the surface
potential that is one important Point uh
which you should always be careful about
now since I've applied a potential
I would expect to see that uh the total
charge neutrality should be still
maintained taking into account the vgb
right and so this brings to our single
point conclusion the takeaway from all
this discussion is that look at the
right hand slide and this is the one
slide which I want you to refer and that
will be your important slide before we
shift topics that the surface potential
is a rising potential As you move from
the the the bulk towards the surface if
you if you go go go ahead and do it so
this is the rising potential which you
happen as you reach the Silicon silicon
dioxide interface it is it's maximum
within the oxide layer you will see a if
not that rapid rise but a small rise in
the voltage and that is CX quite quite a
large substantial amount because that's
an oxide layer subsequent to that you
will again see a rise because it should
reach the metal work function or the
metal potential right so and any
potential I'm giving on the gate voltage
will be substantiated by the oxide
change and the surface potential change
with this uh we we have also understood
the basic fundamental principles of the
flatband and the fundamental principle
of uh the charges this will be useful
when we do the formula will or the
energy band
diagram let me come to uh let me come to
the Moss basic electrical properties of
mos device and that will be quite
interesting or useful to all of you uh
two things which is important and uh
let's go basic let me give you a basic
Mass law action and I assume that you
will be understanding this uh to refer
please go to some other NL course or
from a basic book and I'm keeping it to
the Bare Basics so that you are actually
initiated to the subject uh there is a m
law action uh which is which happens in
any MOS device and that is that is
referred to as NP is equal to ni squ
which is written
here what does it mean is that that the
equilibrium concentration of the mobile
charge carriers in the semiconductor
will always follow the mass low action
which means that the product of the
electrons free electrons and holes will
always be equal to the square of the
intrinsic carrier concentration right so
you see n into p is equal to n i s
primarily meaning that n will be
approximately equals to n i s by P or P
can be written approximately equals to n
i s by n right
now n andp obviously denote the mobile
carrier concentration of electrons and
holes now let's take an N type
Semiconductor in an N type semiconductor
P will be obviously the minority current
carriers and electrons will be majority
current carriers so what happens
therefore is if you place the minority
current carriers P here which is very
small quantity obviously your n will be
very large and vice versa when you take
a p type semiconductor so this is for a
p type semi conductor uh you want to
find out the majority current carriers
and this is for an N type semiconductor
where you find it for the electron as
the majority current carrier the
intrinsic carrier concentration at 300
Kelvin is given by 1.45 into 10 ^ 10 per
CM Cube now if you assume that you dope
it with the third group element which is
an acceptor ion na then obviously I will
get my number of holes will be equal to
the concentration of the acceptor ion if
I assume 100% ionization primarily
meaning what that all the na particles
which you have inserted from outside are
contributing to one whole then we Define
that to be as a 100% ionization so what
is a 100% ionization let me explain to
you once again 100% ionization primarily
means that each na will contribute one
whole to the system so if you have
inserted 100 100 Boron atoms per CM Cube
then you will get 100 holes per CM cube
in that domain right now if this is true
let's come to the last statement of the
slide which tells me that NP 0 is equal
to n i s by n which means that NP 0 is
basically the minority charge
concentration if it's a p type element
and in and if I assume 100% then all my
na will be equals to p and therefore if
you look at this expression here uh I am
replacing P by NA so what I get is NP 0
= to n i² by NA
right and this is what you get to ni squ
by na na is the acceptor charge
concentration so this is the number of
electrons which you get and the number
of holes which you will get will be
approximately equals to ND in this case
right and that will be giving you a
value of uh number of holes in the P
type semiconductor will give you the
value here this gives you a brief
background about the Moss electrical
characteristics now let me come to the
fundamental principle based on which we
will be studying the energy band diagram
which you will be studying in some other
course I'll just give you a precursor to
that now if you if you take a silicon
silicon is basically a catenated
material which means that silicon's each
bonding will be surrounded by four Bond
here one 2 three four bonds so silicon
is a group Four Element and this four
bonding will be there once you dope it
with an external element say phosphorus
which is a group Five Element then what
it does is it remove one of the Silicon
Place itself there and it
it it it combines with the nearest
silicon neighbor but then it has one
extra electron which it leaves apart and
if there are 100 such phosphorus atoms P
per CM Cube we will have 100 such number
of electrons being also introduced right
and this is what is known as silicon
doped with phosphorus atom now how does
it how does it influence
our our energy band diagram you all are
aware that energy band diagram will have
a induction band a Vance band right and
an intrinsic fmy level now you might
have also known that a firi level is a
place where the probability of finding
electron at 0 Kelvin is half right which
is somewhere in the middle so if you
look at the intrinsic FY level it will
be somewhere in the middle it will be
forming an intrinsic fmy level now
conduction band and above conduction
band is the
state which will have if you so so look
at very important point on the y- axis
it's en electron energy so you see the
conduction band Edge will have the
minimum electron energy any free
electron will have minimum energy at the
conduction band and therefore the edge
of the conduction band is the most
stable part of any design of any
Semiconductor in terms of any any
electron free electron why because the
energies are minimum when the energy is
minimum that's where the electron will
like to sit right so this is but as you
as you give more and more energy let us
say through Optical domain or through
biases the electron energy will go high
and the electron will be shifted higher
and higher in the conduction
band right and when you remove the
energy they will dissipate the energy to
the lattice and come back to again to
the edge of the conduction band this is
what we have learned second thing is in
the valence band if you look there are
no free electrons right to generate free
electrons you have to give an energy
equal to this band gap which is EC minus
EV this is your band Gap here which
energy you have to give from an external
source for any electron to jump from the
valance band to the conduction band
where it will be treated as a free
electron now with this basic statement
clear to you let us introduce a
phosphorus level in the energy level
diagram now phosphorus is basically a
one which is contributing an electron
right so the the the donor level Ed
which you see in this diagram this one
is very close to the conduction man so
look at from the energetic point of view
not from the uh space point of view if
you place a level very close to the
conduction band The amount of energy
required for that band to give free
electron to conduction band will be
relatively very small you don't have to
give an energy equal to EG which is the
band Gap in order to shift an electron
you have to give an energy which is
Maybe 110th or 11 15th of that energy
which will be very very small so the
phosphorus energy or the phosphorus
energy is somewhere lying in this region
this is the discrete band which is there
lying in the phosphorus
atom I hope it is clear to you in this
case in this case so let me give you a
reverse statement and explain to you
what will happen if you had doped with
Boron atom if you are dope with Boron
atom then this phosphorus will be
replaced by Boron but boron has only
three U three bonds because it's a group
three element it will do what it will
make a make a connection with these
three silicon but with this there will
be a hole available why because there is
no bond formation taking place between
them and therefore it will be forming a
hole there right so any Boron which you
insert will introduce a hole assuming
again 100% ionization the Boron or the
acceptor level energy level will be very
very close to the valance band so the
acceptor level will be very close to the
valance band this is EA or acceptor
level we also write it as e small a
bottom line which means that so if you
want to generate a hole you just have to
shift it from the valance band to this
particular point which is also very very
small as compared to EG once you do that
you have a hole available here right so
what does donor level do donor level
gives an electron and itself converts
into a positively charged and that's the
reason you see it's positively charged
here right and it's negatively charged
here what what about boron a group 3
element it itself gives a whole itself
becomes a negative charged particle so
what will happen is it will accept an
electron from there right so this will
become negative in nature and they will
become holes here so it will be positive
in nature and these are all free charge
carriers which will be available correct
so this is the basic understanding of
the energy level which you see keep that
into your mind and we'll go step by step
now to build up the energy level diagram
look at the right hand side corner on
the diagram and what we have done is
where we have we have introduced a
positive bias to the gate side of a moss
moss device this is your metal right
this is your metal and and and and this
is this is the metal the an oxide layer
and this is the semiconductor this is
the semiconductor this is the oxide
layer I've slightly uh sort of uh
enhanced the image right and and we have
taken it so any positive voltage you
give on the gate side it will generate
an electric field down below and
therefore if you have a p type substrate
on the semiconductor the holes will be
thrown inside the substrate so that's
the reason you see the holes Arrow Head
is showing in this direction why because
I've given a positive voltage on the
gate side when I give a positive voltage
on the gate side this electric field
working downwards as the electric field
is working downwards the holes will be
pushed down Wards when the holes will be
pushed downwards you will have minority
current carriers electrons sticking to
the Silicon silicon dioxide interface
right let's take that picture which you
see on the left hand side and place it
on the right hand side picture the
knowledge which you have gained when you
put a positive bias here you see uh you
will have you will be inducing a space
charge region the blue color is the
space charge region why there will be a
space charge region because see what
will happen initially is as you give the
positive bi is you are pushing away the
holes right once you push away the holes
the Shaded region will be devoid of any
free charge carriers there will be no no
free charge carriers
here there will be no free charge
carriers why because you have pushed the
holes away from the interface silicon
silicon dioxide interface and since you
have not applied any bias on the drain
and sorts in fact there is no uh no
discussion of source and drain so there
are no horizontal electric field there
is only lateral electric field or
vertical electric field so what we are
saying is there's a presence of vertical
electric field and uh the horizontal
electric
field horizontal electric field is not
present correct is not present obviously
it's not present and that's the reason
you will get a depletion charge
here and higher the P type doping
concentration of the substrate is lower
will be the value of your depletion
charge so you see XD which you see here
XD is the thickness of the depletion
layer if your duping concentration would
have been very large in a ptype
semiconductor this XD will be as small
as possible right but if the P type
doping is very very small XD will be
relatively large please try to find out
what is the reason for that from any
standard textbooks or any other NP
lecture right why is it why is it like
that this comes the first step that the
first step is to remove the free charge
carriers from the Silicon silicon
dioxide interface and a depletion region
is formed which I have shown here right
this is also known as the space charge
region more is the value of your voltage
more will be the thickness of your
depletion because you're reverse biasing
in a sense the depletion thickness right
and as a result what will happen the
depletion thickness will become higher
and higher with this knowledge or with
this concept let me re frame a question
for you think about it later on the
question is if I would have replaced
this P type right by an N type
semiconductor and applied a positive
bias then what would have happened right
uh think about it and we can discuss
this later on as we move along but this
is the this is the basic Moss capacitor
why because you have a metal oxide
semiconductor and I have applied a bias
here now once we have done that let's
correlate uh the bias with the band
diagram and the flat band so we have
already studied the flat band we have
already discussed the bias conditions uh
we will now come to the condition where
we will have a zero bias a positive bias
and a negative bias on a basic M
capacitor
structure if you so so look at it this
has been so look at this structure right
this is the Moss and this has been
shifted in this domain so you see this
gate is available on this side and then
you have an oxide layer and then you
have a semiconductor so this is a p type
semiconductor which you see since your
semiconductor is p type I would expect
that my firy level EF will be close to
the valance band right if it would have
been an N type semiconductor my f level
would have been close to the conduction
band obviously the intrinsic FY level
will be somewhere in the middle or at
the middle of that
Junction now when you apply a zero gate
voltage or a zero zero bias there will
be no bending of the bands and that's
correct also why because the bending of
the band takes place by virtue of this Q
into V energy is equals to Q into V
right when you apply a voltage and you
multiply with Q you get energy in terms
of this but if your V is equals to zero
obviously e will be zero and when e is
equals to zero it will be all straight
line aligned as you can see in the side
it a very straightforward way of looking
at it let us first apply a positive bias
right we apply a positive bias on the on
the on the gate side when you apply a
positive bias on the gate side you are
effectively uh looking into the fact
that on the right on the P type
substrate you will have a negative bias
or or negative charges will be
accumulated by the concept of neutrality
once you do that since the energy levels
have actually gone down because it's
minus Q * V because it's electron you
see the bands are bending downwards near
the oxide layer and you can see the
conduction band has bent downwards the
intrinsic firmy level is bent downwards
and the EV is also bent downwards right
and effectively therefore very if you
look very closely now near the interface
which is the silic silicon dioxide
interface this one your firy level is
slightly closer to the conduction manand
and slightly away from the valance
band interesting to see the FY level
does not change it is still the straight
one think about it why is it like that
right I will not discuss that in the
class here the intrinsic FY level the
conduction band The valance band and the
fir level will all dip downwards the
reverse will be true when you apply a
negative bias when when you apply a
negative bias there will be positive
charges accumulation of hole near the
interface right this one is basically
your depletion region this one this this
typically is your this typically is a
depletion region XD similarly yes so
this is this is your depletion region
since holes are getting accumulated
charges are increasing Q into V is
larger and the band tend to move upward
in the case in this case uh now you see
very interesting the same logic which I
discussed to you in the positive B you
the same logic here because of the
positive charges near the interface the
valance band is becoming very close to
the EF right I'll just rub this here and
then you see look just concentrate here
if you concentrate here the light dashed
blue curve line straight line is now
very close to the black line of the cond
balance band which means that the
balance band is relatively closer to the
fir level assuming therefore I have
large number of free charge carriers
being developed in this case Okay so
this is the basic Moss capacity and
energy band diagram which you
see we have understood the depletion
region so let's have a um sort of a
methodology which will give me a brief
idea about XD or the depletion width
just to keep in mind the depletion width
is given by this where FS is the surface
potential right we have already
discussed this potential FS now you see
let's look at the right hand side
diagram and we will correlate that with
the depletion thickness look at the
right hand side diagram this is bending
downwards bending downwards please
remember what which means that what
voltage we have given look at the if you
look at the previous slide bending
downwards primarily meaning I've applied
a positive gate bias right so I have
applied a positive gate bias here
positive gate
bias and I have got a negative side here
right right these are and in this
depletion region there will be uh
immobile charge carriers immobile charge
carriers so there will be no mobile
charge carriers and uh so so this will
be having that value here now what has
happened is as you apply a positive gate
bias the the conduction band Edge goes
down the intrinsic F me goes down and
the balance band goes down and the
distance between the interface and the
point from which it starts to go down
that is defined as my depletion width
why because Beyond depletion width you
enter into a region where uh the
potentials are again constant the effect
of the potential on the gate side gets
nullified beyond the depletion width
till the depletion width you have a
variation Beyond depletion width it's
almost the straight straight line right
and that's the reason you see EC EFI EF
and EV are all straight line beyond the
depletion width it is given by 2 Epsilon
silicon 5S upon Q * na where na is the
accepted ion concentration and Fs is the
surface
potential now this is an interesting one
how do you measure the surface potential
right you measure the surface potential
by seeing the difference between the
intrinsic firmy level between the so let
me rub this so that it's clear to you so
how do you define uh the intrinsic fir
level you define the intr surface
potential as the amount of the amount by
which either the conduction manand or
the intrinsic firy level has gone down
by application of a external potential
that is defined as my Surface potential
or the potential which is available at
the surface of the Silicon silicon
dioxide is referred to as the surface
potential right and uh that is is given
by F S here so just place the value of f
s in this expression and square root of
that is XD which means this is quite
interesting that f
s uh so XD or the thickness of the
depletion is basically dependent on the
square root of f s so it's not linearly
dependent it's dependent as square root
so it's a parabolic dependence will be
there right and that is quite
interesting in this case uh we we Define
another term which is basically the
potential 5 q5p or e5p and is given as
thermal voltage vth which is 26 molts L
at 300 Kelvin Ln of natural log of Na by
ni and this is known as 5p and explain
to you another in another uh way later
on but that is what is the value of 5p
right uh so this this uh in an extent
gives me an idea about the depletion
layer thickness here and uh we also look
at the surface char density right which
means that can we predict the electron
concentration which is there in the
conduction Band by looking at the
difference between the intrinsic F level
and the firm level so you see it is
given by this form that n is equal to n
exponential EF minus EFI if this
difference is larger which means the
firmy level has actually shifted towards
the conduction band more the difference
will be larger and therefore my electron
concentration will be larger which means
that if my fmy level is Clos to the
conduction band more is the
concentration of electron if my firy
level is closer to the valence band then
more is the concentration of my holes
right so this is for the N type
semiconductor which you see uh for for
if you take a ptype semiconductor
substrate the electron inversion layer
is given by this formula uh you don't
have to worry from where we are getting
it at this stage but just keep in mind
that it depends upon the value of the
ffp here which we have already defined
plus Delta f how much Delta FS are you
doing so 5fp is the absolute value plus
Delta f is the change in the surface
potential by virtue of an external
voltage right or external bias and VT is
the thermal voltage which you see this
is known as the surface charge density
uh which you
see how so how they're actually formed
we already know how these are formed so
if you have discrete atoms very far off
and you try to bring them closer and
closer the band formation takes place
right I would uh request you to study
the good books on there's a good book
which is source is given as Neiman here
have a look at Neiman or even Streetman
and bgy is a nice book to discuss all
these basic concepts of energy level and
energy band diagram right but the the
basic concept is when the two atoms are
very far apart they will not interact
they will they are isolated when you
start bringing them closer the discrete
energy level tends to interact with each
other and now you have bands formation
taking place so you have an energy band
conduction band balance band and the gap
for me this band Gap available to you so
this gives me a basic idea of the
formation of the energy
gap uh we will take it take this up in
the subsequent uh part of it thank you
[Music]
a
[Music]
