Easy Way To Hang Pictures Using the Hang Hero™!

DirtFarmerJay
310 followers
96 Video Views·Dec 28, 2024
hi dir farmer J here from dirtfarmer
j.com Recently we came across a product
called hang hero that promises to make
the task of hanging pictures a lot
easier and allinone where it actually
drives the nails and tells you where to
position them we're going to put it to
the test we're going to tell you the
Good the Bad and the Ugly stay
[Music]
tuned hi dir farmer J here from
dirtfarmer j.com we have right here
what's called The Hang hero the Hang
hero does a couple things one it has a
level bulb right here so you can tell
whether or not you're hanging the
artwork or the piece of art or the
plaque or whatever it is evenly number
two it has a scale here both metric and
Imperial uh so that you can figure out
how far apart to put the nail drivers of
the Brad drivers number three it has
these Brad drivers that you actually
insert a Brad in the back and just
actually push it into what's called a
gypson or sheetrock wall this device
does not work on solid walls like
plaster wood concrete that sort of thing
although you could maybe use it for
marking uh to be able to drill in
Fasteners or drive a nail or whatever it
might be but this is for drywall or
sheet rock walls the next uh feature
that's on is you have these two uh
devices that you're going to put push in
here but this one's a fixed on this end
and holds the zero position where this
one slides back and forth up and down
the beam and inside of it there's an
indicator that tells you how far apart
the two Center points are now if you
don't need to drive two Brads you can
also on the back of this pull off the
clip on the end and this will come right
off the beam and you can just use this
singlehandedly to get started what
you're going to need need to do is
determine on the wall where you want to
place the item now in this case I'm just
going to split the distance here
visually between this room name right
here and the edge of this molding and
place the r workor about centered in
here the second thing is to look at
whether you need one Brad or two if it's
one Brad the manufacturer uh indicates
that that'll hold up to 5 lb and if you
put up two Brads it'll hold up to 10 lb
and a/ in sheetrock wall all right so
here's our piece of art we're going to
hang uh hang up this is a nice gift some
friends of ours and uh as I turn it
around you can see it's got a wire
mounted across the back well I have two
options here one is to hang it with one
attachment point or to hang it with two
and I would always choose two on this
kind because if the two attachment
points are Level uh it makes the picture
hang uh in a stable fashion
and you can adjust the pitcher back and
forth and get it so it's hanging
straight on those two Brad points if I
hang it on a single one it's really easy
to be left or right of the balance point
and things like slamming
doors uh a mild earth quake any of that
sort of thing or somebody bumping the
wall can literally have the picture
shift and you're going you're going
around and then having to adjust this so
we're going to do two points so what I'm
going to do here is estimate I want this
picture to be about right in here I want
this to be up in here someplace so uh I
can either mark the wall in this case
we'll just estimate that it's going to
be a little bit below where there's
another Mark here but we'll go ahead and
put it right in this area right here
I've determined that the distance
between the two points where it'll put
nice tension on the wire and help the
balance is 8 in apart so this one is set
at zero and then I'm going to move the
indicator that's in here over to the 8
in Mark and there it
is all right now that I've got that and
I know that I want the nails which right
on the side of this unit you'll see an
indicator that says where the nail is
going to be punched at what level it's
on both sides of these units here's the
stationary and the movable now we need
to load uh these dispensers and we're
going to use use right out of the
repository here it comes with an onboard
magazine uh with a magnet here these are
number 17 Brads 1 in long let's go ahead
and load it let's go ahead and put one
Brad right there obviously with a point
out load it in and then we're going to
also load it in this one you see it
disappears into the chamber now we're
going to go ahead and place it up on the
wall and then look at the level to make
sure we're right so we're going up here
the
indicators and we also know that we want
this to be about halfway I'm going to
move this over 4 in Mark halfway between
the two that I've done and I'm going to
say that I want it somewhere about right
in there and where the indicators are
and this is showing level so I'm just
going to take this push that go to the
second one push that pull off and I have
two bread points installed all right
let's Mount our piece of artwork here
and see if we like the results
well what do you think it did a pretty
nice job here of hanging straight and
you can see through the reveal here I
mean if I need to adjust it a little bit
like that uh and double check but quick
and stable and notice that when I pound
the wall the piece of artwork doesn't
shift because it's it's hanging on two
points but again if you only need one
point you can certainly do it with that
unit so what we like about it is it's
all in one you don't need to bring a
hammer um it works really well the one
thing that the Hang hero does not do is
determine height exactly where you're
going to put the Brads we know that for
instance that we wanted the top edge of
this to be at this height but that's not
where the hangers are if you recall in
here there's a wire that's coming
through that's being and suspended here
that lands somewhere in here so you're
going to have to do a bit of calculating
a little trial and error to get this
part to land exactly where you want it
so here's some more thoughtful features
on this uh number one there's an
indicator on these push pads that tell
you where that hole uh or where the nail
is going to come out centered so that
allows you to see out here without
guessing where it's going to be where
that is and as we've seen before there's
these side to sides as well so you have
two alignment marks or indicators are
very helpful also they did a nice little
thing here and that's a hole right here
that you can hang this unit on the wall
in your shop or your garage or wherever
you like to keep these kind of tools
it's easy to Stow right there and third
this feature of where you can move this
back and forth serves another great
purpose other than just trying to
calculate how far part you want that is
to take a known piece of art with a
known distance of the hangers and align
the nails uh to that so in this case if
I pick up this piece of
art and you can see that it's got what's
commonly called Sawtooth hangers I could
line up and I'm one handing this so
forgive me but I could line up where I
want the nails to be on that and use
that as where I'm going to push in the
nails and now the nails will land where
those hangers are whether it's a saw too
uh whether it's a ding type of thing or
perhaps it's even a routed slot with an
opening on one side now you can know
where that needs to go if you're
interested in getting one of these you
can go to my hang hero.com at the time
of filming these were selling for
$6.99 and you can order one there we
don't get a commission on them we just
find product that we think is going to
be helpful around the home or the shop
and this uh I think fits that bill give
it a shot take a look over there and see
if it's something that can greatly help
you if you're doing quite a bit of this
kind of work and you need to locate the
studs or other kinds of objects behind
the wall such as Plumbing or electrical
then check out this product that we did
a product review on the walabot you can
walk through it and see what it senses
how it works and also where to order one
until the next time this is dirt farmer
J from dirt farmer j.com enjoying this
nice piece of art
