Boss Industrial 5” Chipper-Shredder Assembly

DirtFarmerJay
310 followers
84 Video Views·Nov 16, 2024
with a little DIY skill and some help
with heavy lifting putting together the
boss industrial 458 cge 5 5-in wood
chipper shredder is simple and easy this
video supplements the assembly and
operating instructions in your owner's
manual please read and review all
instructions and gather the tools you
need before you begin we recommend you
have a clean work surface adjacent to
your assembly area this will will allow
you to keep parts and tools organized
and
accessible the unit comes packed in a
wood-sided crate with a heavy duty
pallet base Begin by unpacking the crate
using a medium straight bladed
screwdriver and a pry bar open all the
tabs and set the side panels aside cut
away and discard the plastic wrapping
around the machine components locate the
owner's manual engine manual and tools
and set them aside where they can easily
be accessed remove the components and
lay them out in a clean work area for
easy and orderly access during assembly
keep the engine and chipper base frame
on the pallet to assist with assembly
later if any parts are damaged or
missing please call boss industrial
customer service at 800
780
2677 before proceeding
Begin by recording the unit's model
number serial number and date of
purchase in the manual the serial number
is located on the side of the base frame
assembly review the manual before
proceeding with machine assembly arrange
the tools and provided Hardware you'll
need on a clean adjacent surface before
beginning assembly the tools you'll need
include a metric socket set and
ratcheting driver a set of open or
closed in metric wrenches medium to
large straight and Philips
screwdrivers electrical tape a Jack or
jack stand engine oil fuel and a grease
gun with highquality grease Begin by
installing the axle and wheel
assemblies if the wheels were being
mounted on a machine with Drive Wheels
the tread pattern points would be set
pointing forward since this is a towed
machine the points are mounted away from
the toe Direction with the wide end of
the pattern facing the toe bar Begin by
removing the bolts nuts and washers from
the mounting holes for the axles begin
on one side and insert a bolt with the
thread to the outside of the unit into
the topmost hole lift the wheel assembly
with the axle on the bottom side of the
mount and position it over the bolt put
on the washers and nut and thread on
enough to hold the assembly in place
repeat for the remaining three Mount
holes putting bolts in from the inside
with threads to the
outside after all the bolts washers and
nuts are in place on one side tighten
all the nuts to securely hold the wheel
assembly in place repeat the entire
process on the other side of the
unit now install the infeed choot to the
engine and base frame assembly to do
this
rotate the engine and base so that the
infeed side of the base is aligned with
one edge of the pallet set a Jack Jack
stand or set of blocks to about 10 to 12
in or 25 to 30 cm tall and position them
on the top of the pallet on the
discharged side of the unit carefully
tilt back the engine assembly until it
rests on the jack stand or set of blocks
without a tendency to tilt back forward
as the unit is being worked on now
temporarily affix the shoot gasket to
the base unit using gasket adhesive or
short sections of electrical tape
affixing the infeed shoot to the base
and engine assembly is easier with help
the shoot is topheavy during assembly if
a helper isn't available ensure that
needed bolts and nuts are within reach
and use a screwdriver or a drift pin to
help position the shoot at as bolts are
inserted into the mounting holes Begin
by bringing the infeed choot with an
aligning tool inserted in one of the
upper holes place the shoot in position
with a tool going through the matching
hole on the base plate insert a
temporary bolt in the bottom hole and
secure it with a Loosely threaded nut
remove the alignment tool or drip pin
and align the Chute to place another
temporary bolt in the hole where the
alignment tool was continue placing
temporary bolts on the other side of the
flange until the infeed choot is held in
place on both
sides then begin replacing the temporary
bolts working from side to side by
installing the washer locking washer and
locking nut for each bolt position
partially tighten each bolt assembly
while ensuring the gasket is in the
correct position and is not deformed now
tighten all four bolts and securely
Mount the infeed Chute it's time to
install the discharge chute Begin by
carefully lowering the assembled unit
until it rests on the tires and on the
bottom edge of the infeed shoot locate
the four pre-installed mounting bolts
and the gasket for the discharge tube
remove the bolts and set them close by
tape or glue the gasket to hold it in
position place the discharge tube
aligned with the opening and Loosely
install the mounting bolts in all four
positions tighten the bolts ensuring
that the discharge tube and the gasket
are aligned properly install the
discharge deflector housing on the
output end of the discharge tube using
the two adjustable handles on the base
of the housing adjust the position of
the deflector so that is open enough not
to impede the ejection of material when
the machine is in operation now we'll
assemble and install the toe bar hitch
stand and mounting bracket assemble the
toe bar and mounting bracket by removing
the bolts and nuts on the bracket
inserting the toe bar into the bracket
and reinstalling the bolts washers and
nuts tighten until
secure install the two position stand by
removing both the pivot bolt and the
attached locking pin from the bracket
lift the toe bar and bracket assembly
and place the stand under them lower the
bar into the top bracket of the stand
and align the holes install the pivot
Bowl washer and nut tighten and then
insert the Locking pin and secure it
with a
[Music]
clip prepare the base frame assembly for
the installation of the toe bar by
removing the four bolts washers and
nuts position the toe bar bracket and
align the holes on the base frame
assembly insert the bolts threads out in
all four positions install the washers
and nuts and tighten them the battery is
pre-installed and charged now connect
the emergency stop button cable fill the
crank case of the engine to the correct
level on the engine dip sticks with oil
and the fuel tank with fuel use the
engine oil and fuel that are specified
in the engine manufacturers owner's
manual Grease the shaft bearings on both
sides of the base frame assembly you'll
need to remove the safety cover for the
drive belts to access one of the grease
fittings after greasing both fittings
with a high quality grease replace the
belt drive cover your chipper shredder
is ready to use here are a few tips to
keep you safe and your machine in top
operating condition one always check the
tightness and condition of bolts nuts
and adjustment knobs and levers before
operation two check the engine oil level
each time the machine is used and fill
as needed three when storing the machine
for winter keep it covered out of the
weather to prevent water from entering
the infeed and discharge tubes follow
the procedures in the owner's manual for
storing the unit and winterizing the
engine if you have questions while
assembling or operating your boss
industrial chipper shredder our customer
service department is here to help give
us a call at
80078
2677 thank you and enjoy chipping and
shredding like a boss
[Music]
