Building a Self Watering Garden Container

DirtFarmerJay
309 followers
Oct 25, 2024
[Music]
hey dirt farmer J here from dirtfarmer
j.com you know some of you have written
in giving us a call say we love the fact
that you are all about self-reliance
growing your own food doing gardening
the problem is we don't have 2 Acres 3
acres 5 Acres what you guys have we
don't even have a little bitty plot I
live in a condo or downtown or only have
a balcony or live in a place where there
is no open ground whatsoever or have
very limited open ground so how do I get
into the enjoyment the healthiness and
the self-reliance of raising some of my
own food to you my friends this is one
of a series of 6 to 10 different
methodologies you can use to become
self-reliant for your food source or at
least greatly diminish your dependence
on having to go to the store to pick up
some of these things and besides it's
just a great amount of fun and if you
got little ones in your life if you're a
grandparent or you're raising little
ones at home a tomato that a little kid
raised or picked themselves always
tastes better okay so let's get started
the first in our series is a
self-watering container this is known by
its acronym an swc as you can see it
uses commonly available items this
happens to be a couple Homer buckets
from the home Depot there's a little bit
of 3/4 in PVC pipe there's some soil mix
and so forth the really cool thing about
an S swc is that you get to water
perhaps once a week that's all you need
to do number two it's a closed system so
it takes fertilizer only in the top ring
up in the top number three it creates a
very robust uh root system in here that
I'll show you in just a second as well
so this really works out that well and
here is a great thing for those of you
that are in the desert Southwest for
instance Las Vegas Tucson Phoenix where
you get some really hot droughty areas a
lot of wind moving on this really helps
conserve moisture allows the plant to
thrive even in those kind of situations
because there's plenty of moisture as
the plant needs it there's the soil
potting soil and you would add
fertilizer just by putting a ring around
here putting fertilizer this has been
fertilized once about four or 5 weeks
ago but you can see that there's plenty
of moisture in this it's not really wet
it's wicking it from the bottom and I
have a surprise for you in a moment here
now I'm going to put this back on I'm
not going to snap it on but here is
we're going to pull this
out and when I do so you can see the
chamber that's on the bottom and that
chamber and this is quite heavy so I'm
going to set it right there that chamber
at the bottom that you just saw is what
transfers moisture across to the bottom
of this here it wicks in from the bottom
Reservoir into this and feeds the bottom
of this here and as you can see this
tomato plant is doing quite well look at
all the roots here we have a root
structure that's filling this whole
bucket now let's go and look at the
supplies that you need to build this
very container first of all I won't give
credit where credit is due this is
actually a plan out of the urban
Homestead and this is in about page 20
there's a great uh uh diagram so this is
a great start get the book the urban
Homestead secondly other tools you'll
need you'll need a hacksaw you'll need a
PVC pipe cutter you'll need a Sharpie
pen a paddle bit that's about a 1 and an
e some kind of uh cutout saw stab saw a
tape measure a drill motor that allows
you to put in a couple different bits a
large bag of potting soil and for the
wicking chamber you're going to need a
yogurt cup something like this okay all
right that's our Basics let's get going
the first thing we're going to do is
we're going to cut the fill tube you
need to cut a tube about 24
in and I'm going to cut it in an angle
the reason for that is that if you put
it flat and the fill tube just lands
flat on the bottom of the bucket the
water's going have a difficult time
coming out if you cut it on a slant when
you fill in the water from the top it'll
come down Splash out the sideways just
fine without back filling the tube and
the drill hole on the side of the bucket
stops it from overfilling so here we go
we're just going to cut an angle on
this okay so then that's going to be
your fill tube the second thing you need
to do go ahead and Mark where the fill
hole goes or the Overflow hole goes in
the second one and here's how you do
that you put one bucket inside the other
and you hold it up the light and you can
see the line right there and say okay
that's where it is now that we know
where our Mark is you can actually see
the mark through here we're just going
to drill a hole to the side there we go
I use about a/4 to 5/16 Brad Point to
that the first bucket's completely done
there you go as you can see from the
inside no matter how much water you put
in it's always going to leak down to
that level and then level out and
therefore create that air gap between
the top and bottom bucket all right now
here's the more extensive work that
needs to been I pre-mark this just a
little bit and I know
that I want this cup not to come all the
way through so I just drew the outside
diameter of the cup and I'm actually
going to use it as a guideline line to
um to estimate where I'm going to cut
that you don't have to be super super
accurate all this that's part of the fun
on this is that you can just kind of go
at it and what I do is I take the drill
right here and get a couple starter
[Laughter]
holes okay I learned real quick as I was
cutting with this this saw only works
moderately well it'll cut the plastic
okay but here's part of the problem it's
so wide that it can't turn so I've
switched and now I'm going to go ahead
and use this just you probably have one
of these here and you can see you can
plunge this cut
in just be careful where the knife blade
goes and there you go see how it's
plunging
in okay so I've got the hole cut out and
the first uh ATT tempt I cut it was too
small so what I had to do is just trim
it out until it fit the cup correctly
and so here we go here's the cup and
where we're just going to let it hang on
the lip of the bucket into the second uh
bucket this can't protrude Beyond 3 in
below so I'm going to just push that
through and as you can see that's just
about right and meanwhile what we need
to do is put a row of holes all the way
around this it allows the moisture that
gets pulled up and then excess to drip
back into the Container down below so
here we
go now you notice right here that I did
not put one of the holes here the reason
for that is is that we need to put the
fill tube down through the bottom so
we're going to use a 1 and8 in paddle
bit just going to put it in this open
area here where there's nothing close to
it
take that through and just let it go
there we go now if we put just to test
it we put that bucket inside
there you can see that that tube is
going to go right in the bottom I'm
going to tilt it right that way that's
how that tube's going to go there's a
couple more things you need to do number
one we need to put a matching hole for
the fill tube to be held in place and
how you do that is simply using the same
1 and8 in uh paddle bit you're going to
put it right out near the edge over here
so you don't have to be perfect again
you just
simply there you go what it does is just
like that you're going to rotate that
around and you can see that that would
put a fill you can cut it a little
closer if you want now what about where
the plant goes well that's our next step
and what I do is I use the yogurt Cup
itself as the marker now depending on
what what you're going to plant in it I
would say keep a smaller hole simply
because one of the main purposes of the
lid is to reduce evaporation to retain
moisture so the bigger the opening you
put across the top the more loss of
moisture going to have at the top you're
trying to create somewhat of a closed
system here so you can again eyeball
this I just simply use the bottom part
of it Mark
around and what we're going to do here
is just
okay we essentially have the top of our
bucket except for the wicking chamber
done so right now that's where the
plant's going to be now one other option
that you might be interested here may
help you a bit and that is to split the
lid if you like and if you have some way
to cleanly cut this you can cut sideways
right right across the top cut that in
half and that allows you to snap it on
after you put a plant turn our attention
to the wicking chamber remember it's
called a wicking chamber because it's
suspended into the water solution below
it pulls in water and irrigate uh by
diffusion it'll pull it up into
everything here so here we go only thing
we're going to do here is grill a series
of holes around the side not on the
bottom the reason you don't want to do
in the bottom is that that would have
the uh the soil have the tendy to drop
out of it so simply all you're going to
do is use this and
just so now we have the makings of our
wicking chamber real simple
okay top bucket
put this
through wedge it
in what you're going to do is put this
into
there second thing you're going to do is
put your fill tube remember to put the
SL the angled end to the bottom so
you're going to line that up in the hole
in the bottom it's now standing and
hitting the bottom bucket you're going
to go ahead and fill this with potting
soil to the same height that you saw
over here on this dude right here
okay you're going to build it right up
to here move this to where now it is
held in go ahead and plant your plant
put this over or split the lid and snap
it on both sides you can put a little
ring of fertilizer around the side do
not fertilize the plant directly just
put it around here because the moisture
will uh move the fertilizer as it's
needed so what we're going to do here is
put this
on get your plant in there put your
support sticks out the top right there
and then what you're going to do is go
ahead and fill up the botom with water
saturate this a little bit as you do it
get it moist so you're not putting a
moist plant ball into a dry soil mix
okay and at this point you now have a
self-watering container put it on a
somewhat level area looks well supported
another great thing about these is you
can move them around if you've got an
area that gets some mild sun or moderate
sun in the morning and the plant's okay
out there but later on it's a real
roaster you can move the plant in under
shade give it the best of both worlds
some bright shade reflect it light off
or something else well as I said this is
the first A Min series on techniques
that we're going to show you the Urban
Gardener how to make the most of your
yard so that you can grow more of your
own produce the things you enjoy in life
until the next time I'm dirtfarmer J
dirtfarmer
[Music]
j.com
[Music]
the only place you want the water to
transfer is the little basket that's
hanging down that will perforate that is
full of soil so that's the purpose of
this so the Overflow always creates an
air gap no matter how full you fill the
uh the fill tube so what we're going to
do is go ahead
