No More Ceiling Fan Wobble!

DirtFarmerJay
309 followers
24 Video Views·Oct 25, 2024
[Music]
hey dirt farmer jay here from
dirkfarmerj.com
do you have a wobbly fan like this one
well you don't have to live with it
stick with me
and in four easy steps i'll show you how
to never live with this again
hey dirt farmer j here from
dirtfarmaj.com you know a wobbly fan can
drive you crazy but it's not good on the
fan
either it's hard on the motor it wears
things out prematurely
and why replace things sooner than you
have to let's make
longer use better economics of the
things we've got
but if you've got a fan that's doing
this
there's some easy steps you can follow
to get it taken care of
so the first step you've got to do is
determine when it's behaving
the worst well i had set this fan on all
three speeds
low medium and high and the wobble you
see right here developed the most
strongly and was the most pronounced
on low speed so let the fan run at
whatever speed it is where you're going
to do all of your other testing
adjustments because if you get it solved
there
it'll even out on everything else so
step number one
find out when the wobble is the worst
what speed
step number two what you have to
determine is whether or not
each of the individual fan blades are
in the same plane are they tilted up a
little bit are they level altogether is
one down
and the way you're going to do that is
you use a fixed point in this case we're
going to go to the ceiling
i'm going to put a tape measure and
bring it up close to the center point of
the fan blade
and we can see in this one it's right at
about 12 and a quarter let's go ahead
and bring another one around see what we
get
and let it settle and that one's close
enough
again at 12 and a quarter notice that
when you come around the motor
is is suspect whoa whoa we got a look at
here
uh this is most likely uh
one of the big issues so where here we
have 11 and a halfer
so we'll keep note of that it was the
third blade
and you can use a silver so here we got
11 and a half
all right and then we'll do one more
just for grins
and we're back at 12. so it was probably
these two right here
are the most problematic yep that's a
high blade and so forth
so what you're going to do at this point
is check to make sure that all the
screws that are tightening the blades on
are all tightened together
see if that takes an issue if it's been
running for a while and we've had this
fan for maybe 15 years
it's likely they've come loose a little
bit and if they are
tightened then you're going to look at
the bracket itself which you can see
right here these brackets to see
if they're mounted correctly or if
they're bent slightly
and you can kind of adjust this so let's
go ahead and check
the tightness of these this particular
blade
uh was the one that's problematic so i'm
gonna take a sharpie pen if you have a
silver one that's even better for these
dark colors
and i'm gonna put an x up here so that
or a little reference mark on the back
edge too
just so i can see which blade it was
that was there and we'll go ahead and
stow that
and get ready now the next thing we're
going to do is go up here and look at
these screws
and sure enough we've got some of these
screws of work loose
so i'm going to go ahead and tighten
this all down again
to just take out the slop and the blades
and we're going to do that with
all five blades
let's go ahead and check our blade
height to the ceiling from the same
point
and here we are we're gonna let that
settle again
all right we're close to 12.
we're pretty dug on close to 12.
let that settle in again that one's
drooping just a bit
we'll see if it causes a problem all
right
and these are all you're probably not
going to get exactly the same thing
every time but we're pretty close
all right let's go ahead and turn it on
and just see how much we've improved our
situation
you saw the wobble at the beginning
let's look and see what we've got now
all right as you can see there's very
slight improvement
we've actually made a dent in it but not
enough and i would imagine
if we turn this to higher speeds it
would probably get more pronounced as
well
but we're going to go ahead and adjust
from here so what have we got
we most likely have a weight
distribution problem
one of the fan blades is weighted
differently
needs a balance or a weight put on it
this is where the majority of your time
is going to be invested in adjustments
because there's trial and error in this
and you'll need to shut on and off the
fan as you put the weight on different
places
i will tell you this when you shut off a
fan don't be tempted
because of the wind down time to just
grab a blade and stop it because you'll
probably unbalance it more okay
so be patient let it wind down and then
we're going to place that so let's go
ahead
shut this off we're gonna pick a fan
blade and we're gonna use
this little kit which um you can
purchase from
any home improvement store this one
happens to come from home depot
it's just over two dollars and what
you've got in is two
sticky back weights plus a trial weight
or a clip
to put onto the edge of it and move it
around
it's repositionable until you can find
out
where you're getting the improvement so
let's go ahead and shut off the fan
earlier on
one of the blades that was the most off
and was up i went ahead and marked and
so we're just going to try using that
one to begin with
here's a little clip-on repositional
weight and so what i'm going to do is
i'm going to take this and put it
up on the fan and just to throw
a little bit of a different weight on it
and we're going to turn it on and see if
things get worse
or better here we go well that clearly
wasn't it
the method i like to use is to go
diagonally or across
from where i last weighted it so the
weight is out over there
i'm going to put it on one of these
blades here closer
to you let's just try it over here and
see what we get we know that we've got
we tried here and we did a skip we're
going to go ahead and turn it back
on and we'll see did we get better do we
get worse
nope but in that one but we are seeing a
little bit of improvement let's keep
trying
we now found the best balance point if
you look over here
this is hanging just beautifully hardly
any movement at all just very very
slight
but certainly acceptable well let's go
ahead and stop the fan i'm going to show
you where that weight
ended up
all right where it ended up this was the
blade that gave us the most
improvement when we put the weight here
now we experimented
up and down the length of the blade and
once we place
that sample weight all the way out here
everything came into balance so now what
we're going to do is replace
that with a sticky pad with a little
weight on it on the back side of this
and we'll test it one more time let's do
that all right let's go ahead and put
one of these sticky back
weights i've gone ahead and peeled off
the backing on it
we're just going to put it out here near
the tip press it in place
remove the temporary weight and let's go
ahead and test it and see
if our efforts paid off so after putting
that weight where
you saw us place it this is the results
very little movement
nice balance we've solved our issue
well if you have a technique that has uh
served you well in balancing these kinds
of devices
won't you share it in the comments below
and we'll help get the word out
if you found this video to be helpful
won't you like it and better yet
subscribe to our channel and when you do
press the bell or ring the bell
and that'll immediately inform you
approximately every friday when we
publish a new video about
home skills like this out in the shop
the garden the kitchen
truck life are just great product
reviews for hands-on living until the
next time
this is dirt farmer jay
[Music]
you
