Clutch Woes Part 2 - Custom Release Bearing

Screw Driver
87 followers
#machinery #motorbikes #occupations #career
Kawasaki AR 50 - 100mph Challenge - Part 11
More issues with the clutch. hopefully solved after this!
Hi, welcome back to the garage and more of the Kawasaki R1500mah project.
Last time I said I was going to go to the dyno, I did go to the dyno, ran the bike, it made less power.
In the process of making less power I also flattened the clutch release bearing so I thought I'd do a video today of how I solved that issue of the clutch release bearing and made it more robust.
Additionally, I'd like to say thank you to a couple of guys, firstly Dale Taylor, previously known as 50cc tuning, did a lot of moped tuning during the days of moped racing.
He's now known as Taylor Tuning, does a lot of Lambretta stuff but not just that, he does all sorts of tuning.
A lot of time on the dyno, a lot of time on the track, very experienced guy and he's been helping me with this and giving me some tips and tricks and direction to go for doing the R1500mah.
So thanks for that Dale.
Which I think is really important because some of the modern day techniques don't necessarily work on some of this older technology, particularly air cooled.
So thanks for that Paul, much appreciated and I'll contact you soon.
So, on with the show, on with the moped trials and tribulations of the Kawasaki AR50 and at some point I will get to the dyno.
So, here's how I fixed the clutch release bearing, enjoy.
Right, more clutch issues.
I noticed when I was doing the last run that this levers bite point kept moving up and up and up and I did wonder what was going on.
Anyway, I've opened it up, so this is the release bearing that sits in there.
There's a spacer that's actuated that pushes on there that disengages the clutch.
That bearing has gone flat and the pin that actuates it, I'll move that, you can see it moving up and down.
That has got a dimple in it now, I don't know if that's to see.
So, all that force on one area because of the extra springs I put in is not working.
So, solution is this.
It's a needle roller bearing that's obviously flat and I now need to machine this because it's too wide to fit in there.
Issues I've got, if I thin it down I'm probably going to be too close to the needle so I'm probably going to have to take a little bit out of here as well.
Just so I'm not leaving too thin a thickness of metal to support the needle bearing.
Other issues I'm going to have is I think this ball bearing was a little bit lower so I may have issues of putting this back on.
I think it may interfere with this part of the casting.
So, I'm going to put it in, machine it, fit it, see where we get and then it looks like I should be able to just get the grinder to that and grind some of that off and then shorten this pin.
And then I shouldn't have the issue of when I'm coasting down dyno I'm holding the clutch in whilst I blip the throttle to get some fuel through to the engine.
So, I'm not just shutting off and then if I just shut off after a run you've only got the pilot circuit that's supplying fuel.
Air-cooled engines also fuel called lubrication from the oil in the fuel so you can seize it if you just shut off particularly after it's just done a couple of runs.
So, it's nice to be able to hot clutch it and then blip the throttle just to get that coolant fuel through.
So, I'm going to do this then I might actually get back to the dyno.
Right, as I said before I need to take this down from the diagram.
I've got 32mm there, I've got 24mm in there.
That is 29mm diameter where that o-ring is so I'm going to take it down to 28mm.
I still want 2mm either side to support this bearing because there's obviously going to be quite a bit of force and I don't want that pushing through.
So, to machine it I've just made a mandrel.
I've put it in so it doesn't matter whether it's centred or not because I've machined it fresh today.
So, that is perfectly concentric to the tool that's in the tool post at the minute.
And then I've just drilled and tapped an M6 hole so it's going to pick up off the inside.
So, otherwise it's going to have to use an M10 through there and again there was a little bit of play.
So, all I have to do is pop that in there, tighten it up and then that is going to be perfectly concentric.
I've machined it down to 28mm.
OK, I've changed my mind. I've decided to go 29mm just to leave 2.5mm either side.
I figured I'm going to ruin the actuation plate anyway that holds the springs in.
So, what's another mm out of there or 2mm out of there.
So, I'm going to go with that just to try and preserve some strength and I've been crept up with that.
I'm trying to get the radius of the tool in there so there's a nice radius at the corner so there's no sharp edges which would raise the stress.
If I do need to put this back in for any reason I've got the mandrel.
I'm going to take it out on the mandrel and then I can just clock it back in again.
Fort jaw, luckily it fits in there and there's plenty of room for me to bore that out.
I've put it in, I've clocked it in.
The best I've been able to get it.
It's been about half a thou which considering this is just a pressed piece of metal anyway.
I'm going to go with that and see how we go.
28mm
Classical time.
I have a carb, a KX80 carb.
It was recommended by Paul.
Give it a go.
So, I'll open it up and see what it's like inside.
That doesn't look good though.
I guess those screws are a bit too long.
Something to try.
This diagram I made.
So, originally it was 26.2mm there.
That was 26. There's 2mm clearance.
And the new roller bearing, release bearing, whatever you want to call it.
I want to put in is 32mm diameter.
I was going to reduce it to 26mm and then put this at 28mm.
That's 28.2mm but I had a think.
It's this thickness here.
The more I take off here, the thinner it gets here.
So, I only went down to 29mm which gives me 2.5mm thickness which I think should be OK.
I guess time will tell.
And I took this out to 29.2mm instead.
So, that is the spring actuation plate holder.
And then this is the part I've machined it now.
I spent time just making sure I got a nice radius in there to reduce any stress raising.
That will now fit in there.
There's a little bit of clearance I guess for self-centering.
And then there was 0.2mm on part took out so I made it exactly the same on this.
And then this will all go back together.
So, what if I get a needle bearing?
The needle bearing goes in there.
This bit goes on top. It's got a groove for circlip.
Fits in there.
I've got circlip on the back. I'm just going to grease this up and then I'm going to stick it in.
And then see how too far this comes out.
And how much I have to take off the actuation pin in the actual side case for the crank case.
The clutch.
As always, issues with doing bespoke stuff.
Fits in there.
It does just clear the springs however.
It's catching on these.
So, I'm going to go back in the lathe and just take a little bit off here.
I've taped it up.
Cleaned it, taped it so no swarf can get into the bearing.
Hopefully then it might fit.
Right, I think fully modified now.
Circlips on.
Took some more off that outside diameter.
It was catching on these. I had a closer inspection and realised you can actually do these up.
And it's not completely concentric.
I don't know whether it was just auto.
However, I've now spent a bit of time making sure that's concentric.
There's the extra few mm off there.
There's plenty of play there.
So now we'll find the next pinch point when things don't fit.
Meanwhile, back at the clutch mod.
The clutch case cover has gone on.
I've got a bit of slack in there.
If I operate the clutch, it disengages fully.
And it releases.
So I don't appear to have any issues with this interfering with the new bearing.
I've marked this up, the lever arm and on the case.
I'm just going to then take this case back off and have an inspect just to check there is some of that push rod protruding.
So I know that there's definitely nothing going to be catching on this case itself.
And then I'm going to call that done.
Take it back to the dyno and find the next weak point in the clutch system.
Outro.
OK, thanks for watching.
I hope that gives you an idea of how I solved this issue.
I'm sure there'll be more with the clutch.
I don't think it's over.
It's given me problems so far.
But as I mentioned earlier on, I went to the dyno and made less power.
I've had issues with carburetion.
Since I've kind of fitted the re-block and something I haven't done that I'm guilty of.
It shows my inexperience of tuning two strokes.
I didn't do a leak down test.
I don't have a leak down tester but I do have a pressure gauge that goes up to 15 psi.
So I'm now just filming this and I'm going to go straight into making a leak down tester which is going to be in the next video.
So we'll find out how many leaks I've got and hopefully that's why it's not carbureting properly.
If you liked today's video and you're enjoying the series then please feel free to give us a like.
Maybe subscribe and share.
Thanks again. Cheers.
