Craft Show Challenges: Mastering Door Corner Displays!

Kim and Garrett make it
277 followers
980 Video Views·Sep 21, 2024
What is up? Welcome back.
Do you like to do it, build it, or make it?
So do we.
And we have new videos each week.
We love these door corners.
They sell like hotcakes.
I love these. They're small.
They fit inside a desktop laser.
They sell like hotcakes, but we barely bring them to the show.
We don't have a good way to display them.
If you have the wire racks as your displays at the craft shows,
I don't know where you would hang them on a wire rack.
We have the pegboard,
which we have two pegs that we can put them on.
But as soon as I put them on the peg, they just fall forward.
I know I've broken at least five of them.
We tried the old crate on a table,
but we only have a four foot table, so we don't have a lot of room.
And there's no back to it.
So they tip forward and fall around.
And you can only display like one style at a time.
So this season we are in the peak of craft show season.
We are determined we're going to bring some door corners and sell them
at the craft show.
And we got to figure out how we're going to do it.
We got a couple of ideas.
I got a really good idea that will make it versatile enough
that we can display them on my table.
We can display them on the wire rack and we can put them on the peg boards.
And we think it's going to be small enough that it'll fit in your desktop laser
so you can cut it if you have a desktop laser to a large laser either way.
And we're going to use MDF.
So I think I think we've got it figured out.
Step one, we're going to gather all of our supplies.
We're going to need some quarter inch MDF,
because this is what we're going to cut everything out of.
We're going to paint it.
So we're going to use our Foxy Hughes paints.
I think we're going to use some wood graining.
So we're going to use our wood grain tool.
And then we think the step out of frame,
we're going to add some trim to it.
Now, we have differing opinions.
It's not we think, one of us thinks.
We are. We're going to add some trim to it.
One of us thinks it's going to be too big.
And that's it, right?
And that is it.
Step two, we're going to make some test cuts.
We have a design that we think is going to work,
but we need to go ahead and prototype it to make sure it's going to work
like we think it's going to work in our heads.
If you ever need to prototype something, cardboard will work.
You just have to watch it.
You got to be careful.
It is paper and you want to make sure it doesn't catch on fire.
I keep a little squirt bottle full of water by the laser,
and I just missed it when I see it to start to smoke.
But it's a great way to test something out before spending money on wood
or whatever products you have, acrylic, something like that.
You'll sometimes the prototyping is the easiest way just to do a little test run.
And we all have Amazon boxes.
Yep.
So we learned a lot about our actual design by making a prototype.
One, I learned that the cardboard is thicker on one side than it is on the other.
That's weird, but that has nothing to do with the design.
So my slots on the side, too deep.
They go too deep.
So I have to fix that.
It seems like on one side, not the other.
That's good.
That's because the cardboard is thicker on this side than the other.
But you'll see that my slot goes too low on on the front and the thing.
And what else?
This this works.
I think this one was a little too deep.
Yeah, this one needed to be smaller.
A little deep.
I need to move these holes back.
And I think that's it.
None of my tabs really fit because I don't know what size cardboard this is.
Right.
But in theory, I think it's going to work.
Yeah.
And you can put them on either side.
I like it.
And if I have a tall one here, put the beach, please, down there.
See how it sticks up.
Now, we wouldn't be able to hang those overlapping like that
on our wire racks, but it doesn't matter here like this.
Oh, the other thing is we need a better top.
Oh, yeah, we need a better top.
This one's a well, it's a little small.
So we're going to go a little bit taller.
On paper, it looked bigger.
Always does, doesn't it?
Step three, it's time to make all of our cuts.
I've adjusted this front shelf.
I've adjusted the slots that were too deep.
And I have just the backer to just make it a little more robust.
Now, none of this, none of these slots and tabs
actually fit with the cardboard.
I don't know the thickness.
But now it's time to actually get our slot thickness.
I measured this MDF with our calipers and it's 0.25 flat.
But I don't think I want my slots to be 0.25.
That's going to be super tight.
Well, we do want it to be snug.
We don't want it to be so difficult to pull apart and put together
that it's going to be squeaking when you assemble it.
Squeaking or break it, try to hammer it apart.
We've done that.
And then we're going to add a coat of paint.
So a coat of paint actually adds a little bit of thickness to it.
You'd be surprised.
So we're going to have to adjust these holes.
Each of these holes to match the MDF.
Now, he says ours is 0.25, yours might be 0.24.
That's what this whole kerfing tool is all about, because it's somewhere
quarter inch MDF is somewhere on this spectrum.
So every time you get a new piece of MDF,
you're going to have to measure how thick it is and then adjust your tabs
and slots.
These are our tabs.
These are our slots to account for your thickness of MDF.
So what is ours?
0.25.
Yeah, exactly.
0.25. Exactly.
Show of how you how you measured it.
So you put it right in your little calipers.
Yeah. And now I can push it in here.
I can push it in.
So 0.25 on this little.
It's tight.
Too, too tight to put together and take it apart on a regular basis.
So I'm just going to jump down.
0.253 feels kind of loose.
I can get it in.
It feels snug and tight.
It will hold on, but I can still pull it out with two fingers
and it should give us a little room for a coat of paint.
So now if it sounds daunting
to adjust each one of these slots
to account for your size MDF, meet me over in Lightburn.
I've got a one minute tip and trick to show you how to adjust your
all of your tabs and slots at one time.
We have our file loaded here in Lightburn.
We're going to make sure that nothing is grouped.
The first thing we're going to do is ungroup everything.
And then while everything is selected, we're going to go up here to tools,
resize slots and selection.
And here you can see we're going to adjust our slot width.
And you can see that none of the slots are currently selected.
So we're going to change our old material thickness to 0.25.
That's what it is.
There we go.
Now it recognized all of the old material thickness.
We want to adjust that to 0.253, and we're going to do this
so that we can have room for assembly, disassembly and paint.
And then we're just going to if everything's not there,
you could always adjust the tolerance and have it look for it
and then hit apply.
And then let's just double check.
This one height is 0.253
and the vertical one width is 0.253.
Perfect. While we're here, we can also adjust the tab height.
So let's select everything again.
Go to tools, resize slots and selection.
Click tab height.
And you can see it automatically recognizes all of the tab heights.
In this case, we know that our MDF is 0.25.
You can always adjust the tab height to 0.253 if your material was thicker.
But in this case, we know it's 2.5.
We're going to leave it at 2.5, so we're good to go.
Step five. Now we paint.
First tee, I think Kim wants everything to have a wood green look.
So we're going to initially paint everything using some whack bat wood
and a foam roller.
Yes, I want.
So it's got to be painted. It needs a color.
It could be stained. You might want to stain yours.
But I want to keep ours light in color to kind of match the standards.
Ours is going to hang.
In theory, it's going to hang on the pegboard standards.
So I want to kind of keep it lighter in color.
Blend it in, camouflage it.
And and I want to give it some sort of decorative look.
So, you know me, I love the wood green.
So I'm going to try the wood green tool on the sides and the tops.
And then we will look into the trim.
OK, the trim.
Don't touch the trim.
I'll just dive.
Anyone gets that reference.
Now that we have a base coat of heist haze,
we're going to come back in with whack bat wood.
We're going to roll it on.
And while it's still wet, I'm going to use this wood graining tool
to scrape it back off, but make it look like wood grain.
It's really all in the wrist.
You got to have a nice, smooth pull
and rock your wrist smoothly at the same time.
It's pretty easy. You ready?
And I think I want to use whack bat wood.
I'm also contemplating white.
I think maybe I should use white.
No, I think the whack bat wood will look good.
He thinks so. I think white.
But we'll see. Let's just give it a go.
Now, the thing about the wood grain tool is you do want this paint wet.
And this dries very quickly.
So you're going to do one piece at a time
and one quick coat while it's damp.
Yeah, he's going to go right in.
I'm going to hold the other end. You got it.
We think I think you've lost your technique.
You did great there.
That was wonderful.
This was too long. You're dragging too long.
What do you think?
I like it. OK.
Do you? What do you think?
Step six, time to assemble.
We're just going to put paint it all together.
It's no glue or anything.
We just know this piece goes first.
There's not the front.
This is the front.
Why? Because it's a little bit shorter.
It's a little bit shorter and the tabs are at the top.
And so are the slots.
Oh, OK.
I'll slide this piece in the back.
It's a little tight back here.
What? Somebody add too much paint?
Paint in the slot.
Got a dirty slot.
Yeah, one of these.
It's a little snug.
Now we add the other one of these.
Is it all the way in? I can't tell.
No.
I feel like it's caught on something.
It's like not moving at all.
There we go.
That's it needs to come up.
Oh, they got to go at the same time.
Well, grain got thick
and now that's how.
There we go.
Oh, the shelves.
I totally forgot about the shelves.
Short shelf goes up front.
The other two shelves should be the same size.
Well, you can't really tell it's a little tall.
Yeah, there we go.
All right.
So so we got so far
looking pretty good.
Step seven.
And now we add the accents.
We're going to cut this trim to see if we're actually going to put it on.
I am horrible at making miter cuts.
Yeah, he is very
he's very much doing salty right now.
I don't want to do this.
I'm going to mess it up.
It's just give her a go.
We have our trim pieces.
We haven't attached them yet because we're at odds.
Well, you just you can help us vote.
Yeah, you vote. Let us know.
So here it is.
With the door corners added, both sides.
No trim.
And then here it is with the trim.
I put my trim here.
Uh-huh.
I'm going to put a whole lot of new trims behind me.
Yeah, I see.
It's hard to see from this side.
So that is option.
Option A is no trim.
Option B with trim.
And then option C, Sarah,
which is the same thing Garrett said, he goes, now you can't see the water.
So we had the kids help vote, too.
Said you could always put it up here on the trim.
And then Tanner said, well, it'll fall off.
And then I and then she said, what if you added like a command strip?
So I have a piece of trim for the front, too.
So we could always command strip it on the thing.
Like, here's the example.
And you take the ones from behind it.
Mm-Hmm. That's what she was suggesting.
Then I like the trim.
Otherwise, I don't think we need the trim here.
Put this one on the trim.
I wanted to show that one.
I feel like the trim might be confusing.
You get rid of this guy.
Well, I got to put something on the bottom.
See, I don't like I don't really love the way that looks with right here.
Like, what am I doing with this open space?
But if you actually have the door corners on.
All right. So what do you think?
Trim, no trim on top of the trim behind the trim.
Yeah, this is what?
Yeah, they could just I still kind of vote.
I still kind of vote no trim.
So I need your I need your opinion.
But in the meantime, we can go ahead
and mount them and see if that works.
Oh, yeah. Let's see if mounting it to the structures work.
And I'm a little concerned about the weight.
So I haven't we haven't tried this.
So we'll put them. This is real time.
Take my trim off.
Have some reusable zip ties that we're going to use to mount this to the racks.
Remember, we put these little holes on the side
and I'm hoping this is going to
work well to hold this onto the display rack.
So this is the metal display rack like most of us started with.
I'm going to a third one, right?
Well, let's just start with the middle one to get it up on there.
OK. And then right about here.
Where are you going?
I don't know.
Let's set it on.
Yeah, like right here.
OK. All right.
It's on there. It's OK.
All right. Let's load some stuff.
OK, well, there's no feet on the rack.
It's just it's at a 90 degree.
Yeah. Yeah. It's holding.
It's a little heavy, but I think once you zip tie this,
I mean, we typically zip tie this to the tent poles.
Yeah. So we need to be you wouldn't want to mount this in the middle of your booth.
But if you mounted it near one of the tent poles.
If you made a square out of these racks
and put them all around it, it would totally balance out.
All right. I'm happy with it.
All right. Now, I'm not sure it's going to work for these.
These are just not quite as.
No, I was going to do the same thing.
I was going to put them through the holes in the sides.
And then on the backside, I was going to put a peg
on the other side of the hole and just wrap it around the peg and tie it.
All right. So it goes through the hole.
Let's give it a try. All right.
Can we try it? Sure.
So we can turn it around and kind of show it around.
Now you go.
Hopefully you can see these are just little pegs.
I would probably use a longer peg.
I might actually put a notch in it so that it wouldn't slide out.
Although it's in there pretty good.
I think it'd be OK.
So you want to try putting some stuff on it?
No feet, but we'll be able to tell if it will lean.
OK, I'm going to hold it down here now.
It's not too bad. It's not.
It's not that heavy.
It's not too bad.
I mean, shaky, but yeah, it seems a little wobbly.
If anyone tries to take.
Well, it's not on feet.
There's no feet.
But even still, I think the top might be a little wobbly.
I mean, we'll have to test this out at a craft show and see how it goes
to the top of the tent to just like the wire racks.
That's for an outdoor show.
And then for an indoor show,
we can either bring the metal or we'll just put it on a table.
So that's the great thing is it's supposed to be versatile
so that you can either display it on your table
or you can display it on your rack.
Oh, oh my God. I thought I saw it falling.
When I saw it, I swear it was coming forward.
Well, we are about out of time,
so if you're not going to join us for the patron after show,
we will see you next week.
We'll do it, build it and make it again.
And a big thanks to all of our patrons.
We love you guys.
That is the best way to support this channel.
And I can't balance this one right now because it's stuck on the backer.
But I made a stunt double.
This one was before you added the holes on the side.
Yes. After we started, Kim's like, you know what?
It needs whole. Whoa, whoa.
And we want to make sure that you can make it with your desktop laser
and we're going to make it out of MDF.
Two hands. Yeah.
And we're going to use glue and we're going to use paint.
I'll try again. Ready?
So let's go figure this thing out.
What was that?
