Lecture: 25 Friction: examples

IIT Roorkee July 201
61 followers
Aug 13, 2024
This lecture covers a few examples based on the concept of friction.
[Music]
[Music]
hello everyone welcome to the lecture
again in the last lecture we look at the
definition of friction the kinetic
friction and the static friction we also
solve couple of examples today we are
going to look at more examples about the
friction so let me first write down the
first problem
statement the question statement
is
determine the distance s
to
which the 90 kg
painter can
climb
without
causing the 4 M
leer to
slip at its lower end
a
the top of the 15 kg
Le
has a small ruler
and
uh at the
ground the coefficient of estatic
friction is
0.25 and it is also given that
the mass
center of the
painter
is
directly above her
feet so to solve this question let us
first make the free body diagram so we
have the ground and the wall
and
uh this is the letter this point is a
this point is
B at a there will be a force
ay and ax at B since there is no
friction and there is ruler so
therefore the reaction force will be in
the X Direction it is also given that
this is 1.5 m this is 4 M therefore this
length will be square root 4 squ - 1.5
whole Square which comes out to be 3.7
M now the weight of the letter will act
at the
center and uh it is 15 multiplied by Z
so therefore 15 G and uh the weight of
uh the painter
is acting at a distance of s which we
have to
determine and it is 90 into
G let's say this angle is Theta so we
can balance the forces in the X and the
Y Direction so from here we have a y is
equal to 90 G + 15 G so 90 + 15 into G
and this comes out to be
1 30 Newton now the value of ax this is
because of the friction so either you
can write down ax or you can write down
the frictional forces its value will be
mu * n so therefore it will be mu * ay
okay and uh of course this is the
maximum value of the friction okay so
this you can write down because now ay I
know and mu is 0 .25 it is given
multiplied by ay now to find out s what
we can do is we can take the moment
about B so therefore BX will not
contribute so let us
take the
moment
about B so we have 15 G4S multiplied by
the perpendicular distance since this
whole distance is 1.5 m therefore this
will be 75 M so 15 into 75 plus we have
a 90 G weight and this has to be
multiplied by the perpendicular distance
so this
distance and this will be 1.5 minus this
distance and it will be S cos
Theta okay plus we have
25 into
1030 into
4 sin
Theta okay because the value of ax is 25
ay and ay is
1033 and the perpendicular distance is 4
sin Theta so this has to be equal
to 1.5
into
130 and this gives you because cos Theta
is also known uh G is also known so this
gives you s = to 2.55
M okay so this was the example of a
leaning letter now let us look at one
more question wherein the letter is at
the
corner the problem statement is
following a
letter
of mass
m and uh length
L
leans
against a frictionless
wall with
a quter of its
length
hanging over a
corner it
makes an angle
Theta with the horizontal
and in the question it has
asked
what will be the angle
Theta that
require
the a smallest
coefficient of
friction at at the
corner to keep the
letter at rest so we have to find out
the smallest value of mu and from there
we have to find out what is that angle
Theta so let me again make the free body
diagram of this
okay this
length
is L
by4 and
uh the reaction forces are going to act
in the following way so from here there
will be a normal
force let's say this is NC C for
corner and uh there will be a frictional
force so because the impending motion of
this ladder will be downward therefore
let us say that the frictional forces
are like that and let me call it FC C
for Corner this point is of course given
Ed C
therefore since the entire
length is L its weight is going to act
at the
middle so this will be mg so this
therefore this length will also be L by4
and this will be therefore L
by2 because the
vertical wall is
frictionless therefore there will be
only the horizontal component so let me
call
it NW
okay now this is the free body diagram
it is also given that this angle Theta
that we have to find therefore this
angle will also be Theta let me fix the
coordinate axis so let's say this is
x-axis this one is the y axis therefore
this angle will also be Theta from the
geometry so first let us take the moment
about
W in that case we have uh
NC into the perpendicular distance which
is 3 l / 4 equal to we have mg into L by
2 cos
Theta note that the contribution of NW
will not be there because we have taken
the moment about W similarly let us
take the
moment about C so we have
mg into L by
4 cos
Theta = to NW into 3 l / by
4 sin Theta let us call it equation
number two and again note that since we
have taken the moment about C therefore
the contribution of NC will not be there
now to find out the relation among them
let us take or let us balance the forces
along the x-axis okay so let me say that
sumission FX equal to Z and let's say we
are balancing this at Point
C okay so we have uh FC the frictional
force its component along the x-axis is
cos
Theta equal to we have a NC Force and
its component so it will
be
mg cos Theta divide
3 sin Theta + 2x 3 mg cos Theta into sin
Theta so I have balanced the forces
along the x-axis and uh the value of NC
and uh the value of NW I have taken from
equation number 1 and two and then take
the component along the
xais from here I can find out what is FC
the frictional force frictional force FC
will be mg / 3 sin Theta + 2/ m 3
mg sin Theta and we know that the
frictional forces has to be less than
equal to Mu * the perpendicular you know
reaction that we have so therefore mu *
NC okay so this is the definition of the
frictional force
therefore we can write down
mg/ 3 sin Theta + 2/ 3 mg sin Theta must
be less than NC NC again we can write
down from equation number one and we
have mu into NC is 2x
3 mg cos Theta this gives me a relation
between mu and
Theta so mg will get
cancel and uh we can rewrite this as Mu
must be larger than equal to 1 / 2 sin
Theta cos Theta + sin Theta /
cos
Theta
okay let me call this
function as F Theta and uh to find
out what is the minimum value of this mu
we have to minimize this function and
that will give us Theta so to minimize
this
function df/ D Theta should be equal to
zero so let us calculate uh the
differentiation of of this so we have F
Theta equal to I'm just rewriting this
it will be tan Theta so sin Theta over
cos Theta is tan theta
plus
cosec 2 Theta okay so let us minimize
this df/ D Theta will be equal to SEC
sare Theta minus
2 c 2
Theta cosec 2 Theta and this should be
equal to zero
therefore SEC s Theta will be 2 c 2
Theta CC 2 Theta and this I can rewrite
as 1 / cos² Theta = 2 cos 2
Theta / sin 2 Theta into 1 / sin 2 Theta
therefore 1/ cos s Theta becomes 2 into
cos 2 a is 1 -
2 sin sare
Theta over 2 sin Theta cos Theta into 2
sin Theta cos Theta cos Square Theta
will will cancel these two cos Theta 2
will get cancel with 2 and we have
2 sin s Theta = 1 - 2 sin s Theta
therefore 4 sin sare Theta = 1 or sin
sare Theta = 1 by 4
therefore sin Theta is equal 1X 2 and
this gives you Theta equal to 30° that
means that for this Theta equal to 30°
our mu will be Minima and this is the
problem statement to find out Theta for
which the coefficient of friction is the
smallest now let us look at another
problem statement and it is following
the coefficient of a static
friction for all contact
surfaces in
figure is
0.2 Doge
the 50 Newton
Force move the
block a
up hold it in
equilibrium
or is it too small
to prevent
a
from coming
down and uh
B from moving
out to find out whether the 50 Newton
force will move the block a up or
downwards let us find out the force that
is required to push the block inside or
to pull the block out outside so for
that let us make the free body
diagram
for impending
motion of the Block
B to the
left okay let me make the free body
diagram of block a
so this is
for block a from the wall there will be
a reaction force let me call it
N1 and since Block B we are assuming or
we are pretending that it is moving
inward
therefore the block a is going to lift
up therefore the frictional force will
be downwards and it will be 2 * N1
because mu is 2 its weight is given it
is 200
Newton and when the Block B is going to
move in the reaction force on it will be
upward therefore on block a it will be
downwards so this is how the frictional
force on block a is is going to act
let's say its normal force is
N2 therefore this will be 2 *
N2 now to find out what is the value of
N1 and N2 let us balance the forces
along the X and Y Direction so sumission
FX equal to0 this gives me
N1 equal to now it is also given that
this angle
is 15° so therefore it will
be 2
N2 cos 15° +
N2 sin
15° let us call it equation number one
now let us balance the forces along the
Y Direction so along the y direction we
we have 200 Newton Force its
weight
plus 2 into N1 that is also acting
downwards plus 2
N2 sin 15° equal to
N2
cos
15° so from equation number one and
equation number two we have two unknown
and rest of the parameters are given so
therefore
from 1 and 2 we can find out N1 and N2
and N1 comes out to be 10 19.8 nton and
ns2 comes out to
be 243 Newton now let us look at Block B
so this is the free body diagram of
Block
B so
external Force p is acting on
it N3 will act upward its weight is
given it is 100 Newton now as I said we
are pretending that the block is moving
to the left therefore its frictional
force will be like that and it will be 2
* N3 and here you will
have 2 into N2 because we have normal
force N2 and of course it is
acting at 15° this completes the free
body diagram of that now again let us
balance the forces in the X and Y
Direction summation FX equal to0 this is
for
Block B summ FX equal to0 gives p is
equal to 2 N3 + 2
N2 cos 15° plus
N2 sin 15° let us call it equation
number three and then we have summation
f y = 0 that gives you N3 + 2
N2 sin 15° = 100 + N2
cos 15° let us call it equation number
four again now from equation number
three and four you can find out what is
the value of
p and it comes out to be 174
Newton okay now in the question
statement it has given that p was 50
Newton therefore this 50 nton force is
not sufficient to push this block inside
because just now we have calculated that
the value for p should be 174 Newton
okay so this implies that force
of 50 nton is
insufficient
to induce a
motion
of Block B to the left
now let us reverse the direction of the
force and find out what is the force
that is required to pull this block
out so
now let us
reverse the direction of
p and calculate
its
value to move the
Block B to the
right okay so note that the only changes
that are going to happen is the
direction of N2 and N1 are going to
reverse Okay so
in the previous
part wherever you have point to N2 this
will becomes - 2 N2 and 2 N1 will become
minus 2 N1 because the direction of the
frictions are going to change so let me
just write down
for block a now the equation will be
summ FX equal to 0 you can look at uh
this equation and as I said uh the
direction of the frictional force are
going to change and of course P also we
have reverse so therefore N1 will be
minus 2
N2 cos 15° plus
N2 sin 15° let's say this is equation
number 5 and then we have summation FY =
to 0 so you have 200 - 2 N1 - 2
N2 sin 15° = to
N2 cos 15° equation number six and from
5 and six you can find out again what is
the value of N2 and N1 so you get N2
equal to 194. one nton
and
N1 = to
12.80 Newton so for
Block
B again we can uh use equation number
three and4 and we can change the
direction of the frictional forces so
this will be p is equal to 2 N3 + 2
N2 cos 15 -
N2 sin5 let me call it equation number
seven and uh we have N3 minus 2
N2 sin 15° =
100+
N2 cos 15° let us say this is equation
number 8 and again from 7 and 8 as we
have done in the last part you can find
out what is
p and uh you can see that P will be
46.7 nton so this implies that
we have to
pull to the
right with this 46.7 Newton
Force to
get Block
B to
move in this
direction okay therefore
four the
block are in
equilibrium okay because to pull the
block we need 46.7 Newton force and to
push the block we need 174.72
and uh the problem statement is
following the
coefficient
of static
friction mu
s between the 100 kg
body and
uh the 15°
V
is
0.20
determine the
magnitude of the force
P required
to begin raising
the 100 kg
body if
a rulers
of negligible friction are present
under the
W Edge
shown and
B the
rollers are
removed and coefficient
of estatic friction
mu =
to20
applies at this
surface as well the concept of this
question is same as the previous
question so here we
have these rulers
and uh we
have a
block which is
being
raised by applying a force
P the weight of this block
is 100 kg let us call it block a and let
us call it Block B
so in the question statement we has
asked to find out what is the value of P
so that the 100 kg block is getting
lifted okay so let us look at
uh the free body
diagram
of block a okay so we have
the following situation note that at
these ends we have a roller support
therefore there is no friction so we
have only R1 let's say and R2
Force since this Block B is having a
impending motion towards the left
therefore the friction on block
a will be like this this and its value
will be mu * R3 where R3 is the normal
reaction the weight of the
block is of course going to act
downwards and it is given that it is 100
kg so therefore weight will be 100 * G
okay this angle is of course
15° so let us balance the forces along
the Y Direction
summation FY equal to 0 so we have 100
into G plus 2
R3 into sin 15° because this
angle will also be 15° and uh the
friction is
2 so it will be point to R3 sin 15 equal
to
R3 cos
15° and we know the value of sin 15 and
cos 15 so this gives you
R3 and R3 comes out to be 10
73.2 Newton now let us look at Block
B so this is the free body diagram of
Block
B the force p is acting on it therefore
the impending motion on Block B will be
left therefore the frictional force are
going to act upward mu * R3
where R3 is the normal force and uh
from the bottom there is going to act a
reaction force R4 there's no frictional
force because it is a roller support and
it is frictionless so let me balance the
force along the X Direction
summ FX = to 0 so we have P = to Mu
*
R3 cos 15° because this angle is 15°
plus
R3 sin 15° and uh again the value of R3
is known the value of mu we know and cos
15 and sin 15 also we know therefore P
comes out to be
4858 nton that means we require this
much force to move this block towards
the left part B wherein the rollers are
removed and replaced by a frictional
surface you can take it as a homework
problem and the final answer for Part B
is p = 681
nton with this let me me stop here see
you in the next class thank you
[Music]
oh
[Music]
