Understanding Friction

Metal Processing Technology Topic
7 followers
4 Video Views·Aug 27, 2025
Friction plays a role in every mechanical system, from gears and bearings to tires on the road. In this video, we examine what friction is, where it comes from, and why different surfaces interact the way they do. We’ll explore static and kinetic friction, the effect of surface roughness, and how engineers can use friction to their advantage
Friction plays a role in every mechanical system.
Whether it's gears meshing,
pistons sliding,
or bearings rotating,
any time two surfaces contact each other,
friction is there, resisting motion,
whether you want it to or not.
But what exactly is friction?
What causes it?
And how can we use it to our advantage?
Let's find out.
At the most basic level,
friction is a resistive force
that acts whenever surfaces are in contact
and there's relative motion,
or attempted motion, between them.
Consider a block resting on a table.
If you push on it with a small amount of force,
it doesn't move,
because a friction force develops
at the interface between the two surfaces,
exactly balancing the applied force
and preventing the block from moving.
As you increase the applied force,
the friction force increases too,
up to a limit.
Push beyond that limit,
and the block starts sliding.
Let's plot this relationship
between friction and the applied force.
The friction force increases linearly
as the applied force increases,
up to a maximum value.
Any additional force causes the block to slide,
and once it starts moving,
the friction drops to a lower,
roughly constant value.
There are two different friction types,
static friction and kinetic friction.
It takes more force to start motion
than it does to maintain it.
So what causes this resistive force
between the two surfaces?
It turns out,
friction is the result
of some quite complex interactions
that occur at the microscopic level.
Even the most smooth-seeming surface,
if you zoom in close enough,
is covered in microscopic peaks and valleys,
called asperities.
When two surfaces are brought together,
it's these asperities
that make the first points of contact.
Because the load is supported
by just a few microscopic regions,
the local pressures at these points
get really high.
For the two surfaces
to slide against each other,
the asperities have to deform or shear off,
dissipating energy in the process.
It's this resistance to motion,
accumulated across millions of tiny contacts,
that gives rise to friction.
As well as the mechanical interaction of asperities,
intramolecular forces come into play
in regions where the asperities
are in close proximity.
Atoms from one surface
form temporary bonds
with atoms from the other,
and these bonds need to be broken
for sliding to happen.
For very smooth surfaces,
these intramolecular forces
can be a big contributor
to the total friction force.
It's also these bonds
that cause kinetic friction
to be lower than static friction.
When the contacting surfaces are at rest,
there's time for more and stronger bonds
to form between the surfaces,
making it harder to start sliding
than to keep sliding.
Now consider two identical blocks,
both placed on the same surface,
but add a weight on top of one of them.
If you push on both blocks,
it's clear the heavier block
requires much more force
to overcome static friction.
This is because the friction force
depends directly on the normal force,
the force that presses
the two contacting surfaces
against each other.
For an object sitting
on a horizontal surface,
the normal force
is just the weight of the object.
The object pushes on the surface
with a force equal to its weight,
and the surface pushes back
with an equal and opposite force.
It's this force that determines
how much friction there is
between the two surfaces.
On an inclined surface,
the normal force
is the component of the object's weight
that acts perpendicular to the surface.
A steeper slope
will reduce the normal force,
resulting in less friction.
In a bolted joint,
the normal force
that determines
how much friction there is
between the two joined parts
is the clamping force
pressing the parts against each other.
It's equal to the preload
generated in the bolt
by applying torque.
And in a brake assembly,
it's the force
delivered to the brake pads
by the mechanical
or hydraulic system.
The relationship between
the friction force
and the normal force
is described by
the Coulomb friction equation.
F is the friction force,
N is the normal force,
and mu is the coefficient of friction.
For a system in motion,
this equation gives
the kinetic friction force.
For a static system,
it gives the maximum
static friction force.
The actual static friction
seen by the system
is only equal to this value
just before slipping.
The coefficient of friction, mu,
accounts for the nature
of the two contacting surfaces.
Let's look at some typical values
for different materials.
The difficulty
with the coefficient of friction
is that it depends
on much more than
just the materials involved,
so these are all
very approximate values.
Surface roughness
has a big impact
because it affects
the likelihood of
mechanical interlocking
at asperities.
Even machine surfaces
with their directional textures
can have different
friction coefficients
in different directions.
Then there's the presence
of surface oxide layers,
cleanliness, temperature,
and even heat treatment
that can all have
an impact on friction.
Because of all of these
different factors at play,
the coefficient of friction
is an empirical parameter.
It can only really
be determined experimentally.
This is often done
using a device called
a tribometer.
The one shown here
uses the pin-on-disk setup
to measure kinetic friction.
A ball of one material,
the pin,
is pressed against
a disk made of
a second material
with a known normal force.
The disk spins,
and the frictional force
is measured by the pin holder,
allowing the coefficient
of kinetic friction
to be calculated.
We saw earlier
that friction depends
on normal force.
The heavier of these two blocks
will see a larger
friction force.
Now consider
a different scenario.
Two blocks with the same mass,
but different contact areas.
How do you think
this will affect friction?
You might initially
expect the block
with the larger base
to experience more friction,
because there's more material
in contact with the surface.
But that intuition
turns out to be misleading.
In fact,
the friction force
is roughly the same
for both blocks.
This can feel
counterintuitive at first,
but makes sense
when you think about
the difference between
the apparent contact area,
which is the visible base
of each block,
and the real contact area,
which is the sum
of the microscopic
contact points
where the surfaces
actually touch.
When you increase
the apparent contact area
without changing
the normal force,
the contact pressure
at the touching asperities
decreases,
meaning fewer asperities
are pushed into
close enough contact
to interlock
or form strong
intermolecular bonds.
The real contact area
stays roughly the same,
and as a result,
so does the total
frictional force.
This is a general observation
that applies to most contacts
involving rigid materials,
but there are
definitely exceptions.
For very soft materials
like rubber,
friction can depend
on contact area,
because of how easily
these materials
conform to other surfaces.
Another possibly
counterintuitive aspect
of friction
is that it doesn't depend
on the relative velocity
of the contacting objects.
Moving faster doesn't result
in more kinetic friction,
because the fundamental
contact mechanisms,
the deformation of asperities
and adhesive bonding,
don't depend on
how quickly the surfaces
slide past each other.
These observations
related to normal force,
contact area,
and sliding velocity
are sometimes referred to
as the three laws
of dry friction.
In many applications,
the goal is to reduce
friction as much as possible,
usually to improve efficiency
and reduce wear.
One material
well-known for its
low friction properties
is the polymer PTFE,
also called Teflon.
It has extremely
low friction properties
thanks to its
unique molecular structure,
consisting of chains
of carbon atoms
surrounded by fluorine atoms.
The fluorine shield
creates an inert
and slippery surface
that resists adhesion
to pretty much
all other materials,
resulting in very low
friction coefficients.
This makes PTFE
a material of choice
in dry contact applications,
like plane bearings,
where it allows shafts
to rotate with minimal
frictional resistance.
So far, we've only
talked about dry contact,
but one of the best ways
to reduce friction
is the use of lubricants.
Clean, dry steel
sliding on steel
typically has a coefficient
of kinetic friction
of around 0.5,
but add a thin film of oil
and it drops to 0.1 or less.
Lubricants work by
introducing a thin film
between the two
contacting surfaces,
coating the peaks
and filling in the troughs
of the asperities.
This minimizes
mechanical interaction
between the surfaces
and reduces friction.
The thickness of the
lubricating film
has a big impact on friction.
When it's very thin,
surface asperities
still make contact,
and although friction
is reduced compared
to dry contact,
it remains relatively high.
This is known as
boundary lubrication.
As the film thickens,
a growing portion of the load
is supported by the fluid.
This is mixed lubrication.
And if the film thickness
continues to increase,
it becomes thick enough
to completely separate
the surfaces,
which is hydrodynamic lubrication.
The relationship between
film thickness
and coefficient of friction
forms a characteristic curve.
Friction is high
when the film is very thin,
but falls in the
mixed lubrication regime
as more surface asperities
are separated by the fluid.
It then rises again
in the hydrodynamic regime
once the two surfaces
are completely separated,
because more fluid
being dragged between
the two moving surfaces
means an increase
in viscous shear forces
within the fluid,
and so increased
energy losses.
The same system can pass
through all three regimes,
depending on the
operating conditions.
Consider a spinning shaft
inside a lubricated sleeve.
When the shaft is still,
there's no motion
to draw lubricant
into the gap,
so metal-to-metal
contact dominates,
and friction is high.
As the shaft begins
to rotate,
the relative motion
between surfaces
entrains lubricant
into the contact area.
This builds a thin
fluid film,
gradually reducing
friction as mechanical
contact between
the two surfaces reduces.
With increasing speed,
the film becomes
thick enough to
fully separate the surfaces,
entering the
hydrodynamic regime.
Unlike dry contact,
with hydrodynamic lubrication,
friction tends to
increase with
sliding velocity.
This is because
viscous forces
within the lubricant
contribute most
to the total
friction force,
and these forces
depend on strain rate,
which is determined
by the relative velocity
of the sliding surfaces.
Lubricants come
in many forms,
each suited to
different operating
conditions.
Liquids, like oils,
are ideal for
high-speed machinery
because they flow
easily and continuously
replenish the
lubricating film
between fast-moving
parts.
Greases, being
semi-solid,
perform best in
applications where
motion is slower,
or occurs only
intermittently,
or where the
lubricant needs to
stay in place
without leaking
over time.
They tend to
degrade more easily
at high temperatures
and high speeds
than oils do.
Most commercial
lubricants contain
additives like
anti-wear agents,
corrosion inhibitors,
and viscosity modifiers
to help the lubricant
function reliably
under a wide range
of conditions.
Not all engineering
problems are about
minimizing friction.
In many cases,
the goal is precisely
the opposite.
Car tires, for example,
are designed to
maximize friction
because that's what
gives a vehicle grip,
allowing it to
steer, accelerate,
and brake effectively.
This wheel is
free-rolling.
It rotates at
exactly the right speed
to match how fast
the car is moving,
so there's no slipping
between the tire
and the road.
At the contact patch,
each bit of tread
touches the road,
and then lifts off
again with no
sliding motion
between the tire
and the road.
When the driver
accelerates,
the wheel starts
rotating faster than
it would during
free-rolling.
To accommodate
this increased rotation,
the bottom of the tire
would need to slip
backward relative
to the road.
But static friction
acts to prevent
this slipping motion,
exerting a forward
force on the tire
at the contact patch.
This causes the car
to accelerate
until its speed
matches the increased
rotational speed
of the tire.
A similar thing
happens when braking.
The wheel is forced
to rotate more slowly,
so the bottom of the
tire tries to
slide forward.
But this is opposed
by a static friction
force acting backwards,
slowing down the car.
If the forces
applied by acceleration
or braking exceed
the maximum static
friction force,
when braking hard
on a wet road,
for example,
the tire begins to
slide instead of
maintaining rolling
contact.
At this point,
static friction is
replaced by kinetic
friction.
Because the tire
can no longer be
directed by steering
inputs when it's
sliding,
and because the
coefficient of kinetic
friction is lower
than the coefficient
of static friction,
this results in a
significant loss
of control.
Increased friction
between the tire
and the road
means increased grip
and better control
of the vehicle.
Friction can also
be used to amplify
forces in surprisingly
effective ways.
Take the example
of a rope wrapped
around a post,
a common method
for securing a load
with relatively
little effort.
The holding force
required to secure
a given load
depends on two
factors,
the coefficient of
friction between
the rope and the
post, and the angle
through which the
rope is wound.
The relationship
between these two
forces is described
by the Capstan
Equation.
The fascinating
thing here is that
the equation's
exponential.
With a turn of
just 240 degrees,
and assuming a
typical rope to
metal coefficient
of friction of
0.3,
the post allows
a 100 newton
pull on one
end of the rope
to hold back
a 350 newton
load.
That's a 3.5
to 1 force
amplification.
Use an extra
turn of the rope
and the 100
newton pull
can hold back
over 2 kilonewtons,
meaning you
could hold up
the weight of
three friends
with one hand
pretty comfortably.
This principle
has been used for
centuries in
nautical applications,
allowing sailors
to secure mooring
lines or huge
sails using
nothing more
than their body
weight and a
few turns of
rope.
Friction is a
critical part of
how mechanical
systems work.
It can provide
useful grip,
cause unwanted
energy loss,
or lead to
damaging wear,
making it something
engineers need to
understand and
control.
And it all depends
on exactly how
the contacting
materials are
structured at
the microscopic
and molecular
scales.
This fascinating
connection between
a material's
internal structures
and its mechanical
behavior lies at
the very heart of
materials science,
and is something I
explore in more
detail in
Microstructure,
a series of
videos I've been
working on that
examines how the
internal structures
of materials can
give rise to
remarkable and
sometimes unexpected
properties.
The most recent
episode dives into
the world of
piezoelectric materials,
materials with a
unique atomic
structure that
produces an electric
charge in response
to mechanical
stress.
This unique
property enables a
wide range of
technologies, from
pressure sensors to
ultrasound machines.
You can watch this
episode of the
Microstructure series
right now over on
Nebula, the
independent streaming
platform built by
creators.
I've been part of
Nebula for five
years now.
It's where I'm
uploading my
Microstructure series,
but I also have a
load of other
videos on there
that you won't find
anywhere else,
covering a range of
engineering topics
like hydraulic
systems, thermal
resistance,
dimensional analysis,
and more.
Nebula is designed
to be a place for
quality content you
can trust.
Everything is
curated, so there's
no AI slop or
clickbait that
doesn't deliver.
Just high quality,
thoughtful work from
some of the best
creators out there.
And there are no
ads or sponsor
interruptions, so
you can enjoy it all
without distractions.
With thought-provoking
feature-length
documentaries like
Boomers, and
entertaining reality
shows like The
Getaway, you'll
always be able to
find something
genuinely rewarding
to watch.
It's also very
affordable.
Sign up at
go.nebula.tv
slash The
Efficient Engineer
and you'll get a
40% discount on
the annual
subscription, which
works out at just
$3 a month or
$36 a year to get
access to all of my
videos and every
thing else Nebula
has to offer.
It's a great deal,
and subscribing is
one of the best
ways to directly
support this channel.
And that's it for
this look at Friction.
Thanks for watching!
