Long boards, straight and square with a Jointing Sled

Nomad Boatbuilding
98 followers
4 Video Views·Jul 21, 2024
howy folks mark from Nomad boat building now today I'm going to process some materials and I thought
I would show you how I go about doing some of that now whenever I bring in fresh material
it's almost always roughson stock that means both faces are roughson and both edges are roughson and
we need to process those into something that we can work with accurately so first step thickness
planning getting it down to at least clean faces if not finished thicknesses and the second step
is jointing those edges straightening those out if I need them straight sometimes I don't
sometimes the natural curve of a plank is exactly what I want but a lot of the time I need them
straight so how do I do that well I don't use a jointer jointing is the process of creating
a square straight edge on your board most people use jointers for this and well that's fine and I
do have a jointer I don't find it's particularly efficient for time and effort I'm almost always
working with long materials stuff that's like 8 to 16 or even 20 ft long using a jointer is
really inefficient the joint is only accurate over the length of its bed and really only kind of like
half the length of its bed for that matter so when you've got something that's already a bit wonky
and you're trying to flatten it on a jointer it's going to take a lot of passes before you finally
get it down to where it's flat and you may never even get it there if it's really wonky to start
with so what I like to use is a jointing sled a jointing sled is really just a plank that's the
same length as the stock you want to join or a little bit longer is even better and we've
got a cleat on the bottom that rides in the track of your table saw and the edge of the sled is cut
off by blade itself so that your finished sled is accurate right up to the face of the blade
now this one's a little bit shy that's fine I've got about a 16th or so of overhang that I have
to accommodate in order to get it to touch that blade but that's close enough now my jointing
sled just has a couple pieces of sandpaper stuck down in a couple spots to help create friction
between the surface of the plank and the surface up the sled and right at the front I've got this
small cleat with some screws protruding through so the points protrude and the front of my plank
just butts up against those the reason I have the cleat at the front and not the back of the
sled is because I can butt the plank up against that cleat and start pushing the plank itself
it's going to push the sled and that means I only have to control one end of the plank so in this
case I've got a plank that's pretty wonky here it's got a big S curve on it usually it's the
side with the crown that I'll favor to take off because that makes it easier to set up on the
sled so here I just drop it on the sled I slide the brunt end up against the eete I
make sure I'm over hanging by a little more than a 16th right at that end and then down
at the other end I'll adjust it so I can feel about the same amount too and I just
let my fingertips tell me how far I need to go and then it's really just a question of
shoving the whole thing through the table saw and making sure this plank doesn't move while
you're doing it if it moves a tiny little bit that's not the end of the world the goal here
is to get it pretty straight it's not going to be super super accurate and I've got a separate
technique of ripping and flipping to help refine any wonkiness that might be in that edge as we
go with the first Edge straightened I'll then measure the minimum width of my plank
and set my table saw fence for just a hair less than that and then I rip the second
Edge and once I've ripped this down parallel I may flip this around and take a light pass again on
the first side that I did to help refine that and then I might flip it around again and do another
light pass on this side and each pass is just going to sweeten it up just a tiny little bit more
by the time I'm done this is plenty straight for the kind of work that I do often with
our local Red cater it's such a stable wood that the edges are usually pretty
straight right from The Sawmill and I can get away with just going straight to the
table saw fence right away and skip the sled but I'll use the same rip and flip
technique to refine that edge to get me down to where I can start cutting to my finished
Dimensions now I realize there's probably some little jig PS that you could apply to
your table saw fence that would allow it to mimic the action of a jointer but honestly
it's not worth the fuss of trying to set that stuff up just a couple of rips and
flips and I'm usually close enough to where I need to be I like to keep it simple this way
even if you plan to use a jointer in your process I think using this ripping sled to
get the first Edge down much much closer to a straight line is going to really save you
a lot of time just going to save you more passes on the jointer the straighter your board is to
start with the more accurate your results are going to be on the jointer if you've ever tried
pushing a wonky board over a jointer to get it straightened out it can be very frustrating
to get through that first hump of getting the really wonky stuff off you can see the width of
the sled isn't super important I think the one I have is maybe about 8 or 9 in wide but I can
drop a 12in wide plank on top of that it really doesn't matter there's just the one or two screws
that grab at the front that are the important part and as long as the sled is wide enough that it's
not tipping off to one side because of too much overhang of your plank it's going to work out
great and then I store this sled on some racks overhead close to my table saw so that they're
easily accessible and I also have some other Sleds on there that are for use with circular
saws kind of like a fesol track saw and with those out of the way I can continue on with
my ripping operations it's all really quite efficient for the most of the work that I do
if I'm getting a clean line along the length of this that table soft fence As I push it through
nice and tight that's as close as I need to be of course every now and then you end up with
a plank that's just too long for your sled and so we have to resort to doing this kind of the
old school way but of course I usually have a slightly different way of doing these things
so we'll start with just snapping a line on our Plank and then I'll rip that line either with
my circular saw or sometimes as in this case I'll just freehand that plank over the table
saw ripping as straight as I can now of course this is a slightly dodgy operation but honestly
I really don't think it's any dodgier than using a circular saw it's a fairly large plank so the
chances that it's going to go flying are fairly low and then it's over to the planking bench
with a nice long jointing plane and we're going to do our best to just try and sweeten up that
line one once we've got that edge sweetened up to our satisfaction
let back over to the table side where we'll use our same ripping and flipping
technique to straighten and square up that edge which of course is the
prime goal of jointing from there on in we're ready to rip down to our finished
widths so you might wonder why I even have a joint or if I never use it well
I certainly do use it but I mostly use it for small Furniture projects or here's a
good example where I'm using it to flatten off the side of a stem great tool for this
job now I realize this technique doesn't really address any twist in the board that is something
a jointer does really well you can sort of get twist out of a board to a degree using
your thickness planer and a sled in that frankly in the case of wooden boat building we're more
often than not putting twist into a board so getting twist out is not something I'm worrying
about too much if you needed to get two boards that are perfectly matched for doing a glue up
fr for instance there's other techniques that don't involve a jointer you could use for that
we'll address those in a future video this table saw sled technique is great for getting rid of a
wonky way Edge getting something that is pretty square and pretty straight and it's really good
if you want to trim an edge down to align with grain for instance either way it is a shopmade
jig that I use virtually on every single project and it has saved me a ton of time
and it has saved me from owning a jointer for the bulk of my career okay I hope that was useful to
you now remember these videos are supported by viewers like you through patreon so if you can
join me over there I really appreciate that you can find links in one of these corners
and it's all is down in the description all right folks catch you next time on no my boat building
