Pottery Tutorial- Trimming a Foot on a Large Bowl

The Story of Ceramics and Porcelain
9 followers
Hello potters and welcome back to the Pottery Plus studios. I'm going to show you today
how I'm going to trim and finish up the five pound bowl that I started on the wheel in the last video.
So let's jump over to the wheel and get started. Okay potters, so today I'm going to be using my
foam bat to center this. Remember you can use a foam bat to center low and wide pieces. It doesn't
work so well on tall narrow pieces, but with a big bowl or a plate it works great. You don't have to
worry about lugs. Mine's not pretty because it's quite old. I need to get a new one, but um yeah
that's what we're working with today. So I've got my bowl here turned upside down. It's leather hard,
meaning it's still a little cool, a little damp, but I can touch it and it doesn't leave a
fingerprint or a mark. And when I start to trim it's going to come off in nice clean ribbons. Okay,
if it's anything else then it's either going to be too wet or it might be too far gone to trim,
if it's coming off in crumbs or making a squeaking sound, any of that kind of stuff.
So I'm going to start by centering just by grabbing it and pushing it towards center
until it doesn't feel like it's bumping my hands anymore. And I know that that's not,
that's a hard thing to put into words, so I know that describing it like that might not be too
helpful, but I promise you the first time you feel it you're going to know exactly what I mean.
And I'm feeling like this piece, like I say this every time, it's not going to be perfect because
the bottom of it is not perfectly centered, but I'm feeling like that's about as close as I'm
going to get it. And I'm okay with that, I can work with that. Now remember friends when you're
centering you don't want to center from down here because sometimes the rim and the foot are
centered differently. And since we're not trimming, well sometimes you might be trimming down here,
but I guess the point is you just want to center where you're going to be doing your trimming at.
All right, so this is quite a big bowl and there's actually a little bit more excess on the bottom
than what I wanted. Like I kind of wish I had pulled a little more up through the walls,
but I did my best and here we are. But it's still, it's still a nice big bowl.
So I don't want to make the foot like too tiny and dainty. So I'm not even really thinking about
the foot here yet, but I know that I don't want it to be disproportionate to the bowl.
So I know I'm not looking to make a really narrow foot, meaning I don't have to bring this in
too too dramatically, but I do need to just really get rid of some excess and make sure that
the curve of my bowl is continued all the way from here and then all the way down into the foot.
So where it's going kind of like straight up right now, I need to kind of get a curve into that.
It's kind of like the reverse of what we were talking about in the throwing portion of this
project, how we want to make sure that the inside like remains curved all the way every step of the
process so that we make sure that the curve is there in the end. It's kind of the same thing
with trimming only in reverse because you're working on the outside, but we want that curve to
be consistent throughout the whole outside of the bowl. Okay, so this feels pretty good and
friends with a piece like this, when it's kind of required that you leave some bulk at the bottom
so that you have enough for a foot, it can be kind of tempting to feel like it's clunky
and just want to trim and trim and trim. Be careful with that. You can always kind of start
getting used to that tapping method where if it sounds hollow, you know that you're probably getting
close to the thinness that you would want. Also, if your tool starts to make a motion like this,
like it's waving up and down, it's probably a good time just to stop and maybe like clean it
as best you can by hand, but that means you've got a thin spot. I know that tapping thing is
weird you guys, but if you tap on your piece like at different thicknesses along the way,
you'll start to hear it and what it sounds like when it gets thin is it has more reverberation
to it like it sounds more like a drum. I'm hearing it a little bit with this one. I think I could
take off a bit more though, so I'm just going to keep going here a little bit. Maybe do one final
pass and then start to decide. I think I do want the foot to be in a little bit further than this,
but not much, not much. You know, you don't want a big bowl that has a tiny foot because if you think
about it, if you fill that bowl up with anything heavy, it's just not going to be very stable. So
okay, I think this is going to be a good size for this foot. I feel like it'll be able to,
this size will be good for the silhouette to make it look a lot more refined, but it's also going to
be wide enough to hold this bowl like nice and sturdy if it's in use or when it's in use. So
what I'm going to do now is I'm just going to start kind of refining or bringing out,
not actually really on a refining step, I'm just kind of bringing that foot out
from that bulk of clay that's around it. So I'm not really like shaping it or anything yet. I'm
just trying to get the bulk of the foot like revealed. I guess that's kind of the word
I'm looking for. I'm just trying to get it where I can see it and then I'm going to go back again
reinforcing my curve of my bowl on the outside and then I'll start to work on that foot.
Folks, something that my students used to get really hung up on was carving or trimming out
the interior of the foot and that's, that is an important step for removing bulk,
but I always just used to like to remind them it doesn't affect the silhouette, like however much
or little material you get out from this part of the bowl, oh might be a little getting a little
dry there, sorry about that squeaking sound, um however much or little you get taken out from
here doesn't affect um the silhouette of the bowl, it doesn't affect the form, it's just uh it's a
like usability and comfort thing. So I don't know people used to always really focus on
that part of the bowl but you know it like I'm saying it doesn't show in the end.
I am going to take some bulk out of the middle of this though. I'm just gonna,
lost control of my tool a little bit, that's okay, if that happens just go back and kind of
do what you can to get your little mistake trimmed out of there and then just keep on
going and I didn't get it perfectly but I think that's all I want to fiddle around with that.
Let's see, you can still see it there a little bit where I went off track but I think if I go
in and define that edge that I was working on when I made that mistake it'll, it's gonna kind
of sort itself out I think, yeah there we go, just needed a little sharper tool to really dig in
and get that definition, yeah that looks okay, I think we solved it. Okay I'm just gonna start
taking little bits out from the middle and you can do this from the middle going to the outer edge
or the other way around, either way and I'm just, I'm using this this side of this tool,
you know this tool is a little small for this but it digs in quite nicely because it is small,
all that pressure goes into that small kind of fine finer point tool and it just helps to kind of
basically trim out a little bit thicker of those ribbons, of the ribbons that we're looking for,
it just takes out a little bit more at a time. I find, I mean I'm sure I could get
a tool like this only a little bit bigger and sharper and kind of
make quicker work of that but you've heard me say it once, you're hearing me say it again,
I do best with just the basic basic tools. Okay I'm gonna start to shape my foot a little bit
and I think what I want to do is take the bulk out of it here so there's more definition between
where the bowl and the foot meet, so I'm just going to kind of angle this tool in like I'm
going like this with it, not as dramatic as that but that's kind of the motion that I'm doing,
give that a little bit more height so I'm kind of bringing it in like a little waist where the
um bowl and the foot meet and then I think I want to kind of round it out a little bit as well
that you can't lean to the side when the camera's in my way like I'm always saying I like to do but
always lean to the side check and see if you like the silhouette, I think I want to make that a
little bit more dramatic down there so I'm going to angle my tool in again and really
yeah get some definition there
and this is what your ribbons should look like friends well at least with my clay I don't know
I feel like that's that would apply to any clay body that you're using but I guess it could look
slightly different but that shouldn't be sticking or sticking means it's too wet scraping means it's
too dry or just keep your eyes out for that okay I think that's looking pretty good
so I know that I need to take out some more right here and when I was being instructed on how to
make bowls taking that curve uh throughout the whole entire piece was even taking a step further
and we were taught to make even this have a rounded curve to it kind of like she would say
kind of imagine if the if the foot wasn't there how would the curve continue on all the way
throughout to this point but that's a pretty challenging it's a pretty challenging thing to do
and you do have to leave yourself a lot of excess because to get any kind of a
curve right here you have to dig down pretty far on this outside edge of the interior of the foot
it's complicated to put into words but hopefully you know what I mean enough and it can just be
very very gently you know it doesn't have to be anything dramatic but just a slight
dome is kind of what I was always told is you know desirable but again that's kind of like
varsity level so I think if you can even get any excess out of the bottom at this point or
you know if you're a beginner or you know even like within your first year or two
I think if you can just clear some bulk out of there that's that's a really good start
it's a really good start I just want to bring some more definition right here to this corner
so that maybe I kind of can achieve that curve a little bit I'm scared to go down too deep right
there I don't know exactly how much material I have but this is just a demo so I'm going to be
brave and try to do it you really get a an angled corner right there okay and I know I know you guys
get the point so I'm not going to go too much further on this but just see if I can kind of
do another shallow pass or two across there and I know that this had a high point when I took it
off the bat because my my bats are getting old too all my stuff's getting old but when I took
it off the bat I noticed it was lumped up there because my bat is kind of sunken in the middle
a little bit just from like wear and tear so it adds a little extra bump to the
bottom of my pieces that has to be taken care of one way or another all right so you always want
to check and make sure that your high point yeah see that's too high it's going to rock on the
table so I have to take some more out of it I'm actually going to switch over to the round loop
because it really takes out a lot quickly for me again I think tools are so much about
preference not about what tools are right or wrong so you could do this any which way you
need it to just kind of trying to move quickly through this so from here folks it's just going
to be a matter of refinement just like always for me it's going to be refining that curve
maybe getting some tool marks out of this getting the crumbs out and away from it that kind of thing
so if you stuck with us this long thanks and I think we'll kind of time lapse a little bit
through this last piece last little bit here and then I'll show you the final product when I'm done
with us I hope you found this video helpful and we always love your feedback so let us know what
you thought and then we'll see you on the next one thanks so much bye
