Making A Twisted Bowl - throwing & trimming

The Story of Ceramics and Porcelain
9 followers
Hey everybody, welcome back to Matthew Kelley Pottery. I hope you are doing well.
Today we're going to talk about making twisted bowls. I'm going to show you the whole process
from throwing, the twisting of it, and then actually trimming as well. Believe it or not,
yes, Matthew Kelley is trimming pots. I know I've had those comments on a couple of my posts
and I actually even took it a step further with these twisted bowls. I trim the inside and the
outside because the weight of these is almost impossible to get to a nice weight without
trimming the inside. So I just decided I was going to go ahead and trim the inside and the outside.
Obviously this idea, just like any idea in pottery, is not all my idea. Obviously I've
adopted it and made it my own in certain ways, but probably a big inspiration from
when William Duvall, Williams Pottery, went to Japan and saw those videos of the twisted
pieces they made. Duane's Pots is another guy on Instagram that makes some beautifully twisted
pieces and then does soda firing. I'm also doing a voiceover on this video because I didn't feel
like talking while I was making these and so I thought, you know what, I'm just going to record
it and then I'll do the voiceover later. So this is what we got for this video, but
as I said and as I showed you with the twisted mugs, the goal with making these twisted pieces
is to throw a a thick slender cylinder. So you want a cylinder that you don't want to pull it
really thin. So that's kind of easier in a way, but then you want to make that cylinder really
skinny and really tall. If you don't make it as skinny or as tall when you go to twist it or you
after you do the facets and then you go to push it back out from the inside, you won't get nearly
as much twist. So a couple tips, things that I've learned. Yes, the skinnier the cylinder,
obviously you want to get that cylinder wall pulled as even as possible so that as you then
carve the facets, which you try to get those pretty consistent as well, you'll get kind of
like an even twist. Also if you use really stiff clay, it doesn't want to twist nearly as much as
if you use softer clay. So those are a couple tips that I've learned. A lot of the twist I've noticed
comes from having that softer clay. Also a lot of down pressure when I go to do the initial
push from the inside after I've carved the facets. That makes a big difference.
So anyway, now specifically on these twisted bowls, something I'm doing different on these
than I did the mugs. I'm going to use a wider wire tool to do the facets on these as well as
I'm going to trim all the way from the near the bottom all the way through the rim. As you'll
see here in just a second, I'm using this wire tool that's just attached to a U-shaped piece
of metal with a wire attached to it. You could use a cheese cutter, whatever you want, but I try
to get pretty consistent cuts with this. You can see I'm not going all the way to the bottom. That
helps with trimming the foot later, but I am going all the way through the rim because my goal with
these is actually to get kind of that uneven rim on top, but I'm also going to trim away some of
that rim later, you'll see, and then push down to get that thicker rim and it's something I've
loved seeing about Dwayne's pots when he does his twisted bowls or mugs. I don't know if he does
mugs actually, but doing his twisted bowls, I love seeing that thick rim that he does and pushes it
back down and it gets that really, you know, kind of wobbly, wobby, sobby look to it. So anyway,
so here's adding the water back to just the inside and then you can see as I push on the inside,
I've got a lot of down pressure and with that softer clay, I'm getting that really nice twist
in there and actually you could, obviously, it's not going to twist nearly as much at the top as
it is in the middle and at the bottom, but I want to get that twist pretty much from here. Now,
I'm just pushing out. Like I said, most of that twist happens from that initial push with a lot
of down pressure. Then my goal is to get that really nice twist in the bottom, like three
quarters of this because then I decided, you know, I'm not going to worry about how uneven the top
is because I realized I'm going to cut a lot of that off so then I can beef up the rim, kind of
start with like an even cut and then beef up the rim. So you can see it has a really cool uneven
rim now, but I want it a little bit different than that. So I decided, you know what, I'm going
to make these and then I cut off like the top like inch, inch and a half and once I get that cut off,
then I still got this uneven thickness around and now what I'm going to do is add water to that
and then push down on it like you would if you were compressing the rim of anything else and
I'm going to kind of let that, you know, if it gets a little uneven, I'm just trying to follow
that as I'm doing that and then kind of push down on the outside as well, kind of curve that rim
over a little bit and then pull out. So now I'm going to do a little bit more shaping from the
inside. So I want to kind of belly that out a little bit more and then I actually push the
rim out a little bit more as well. So I made several of these. This is probably not my favorite
one of all the ones I made, but it was the one that I was videoing. So there I got a couple
others that the rim was a bit more uneven and I like that even better and you'll see when the
wheel stops here, you can see it a lot better where the unevenness of the rim kind of really
comes into play. The other reason, like I said, that I decided to trim the inside of these, you
can see from the top view on this one, you can kind of see it comes down and then it drops down
to that very center part and all that thickness there, unless you trim the inside, all that
thickness stays in the pot. It's not necessarily a bad thing, but it does make them quite heavy.
So you can see here, it's got like, it's leaning to one side a little bit, but then I love the way
that rim kind of like drips down in different spots there, kind of follows where the twists
kind of come up. But like I said, this one doesn't get as uneven as others and so it's not my favorite,
but it did, it still is a nice piece and I got the effect that I was going for, for the most part.
Now on to the trimming of these. I leave these attached to the back. That really helps with the
trimming of the inside. You don't have to use lugs to attach the piece back to the wheel
in order to trim the inside and because I'm not trimming the outside of this other than the very
bottom, you don't have to worry about trimming too much on the inside or trimming
some on the inside and then having to trim the outside. Anytime you would trim a bowl,
you would probably just be trimming the outside and if you trim the inside and the outside, there's a
big chance you could get it too thin. But with this, I could pretty much just trim the inside
and I'm really going, I'm not going in the very bottom in the middle. I'm mainly just going for
that sidewall from about halfway down, down to where the flat part of the bottom was. So maybe
you know an inch or so out from the middle on the bottom. I did speed up this video for the
most part because the making of the piece was like five minutes and then the trimming was like 10
minutes and I'm like nobody wants to see me trim this thing for 10 minutes straight and I don't
know if I have that much to say. So you can see here trimming the inside makes a mess and there's
not that I know of any way around that and so although this is kind of a pain, I've done this
with a handful of pieces now and I love the way they turn out. I love the way they look but it is
kind of a pain to trim the inside and so that's why I had never done it before. Trimming in general
is not something that I really thoroughly enjoy and so I just don't do it a lot. I think it makes
nice pieces but my goal is to throw pieces that are the correct thickness that I don't have to
trim them and even as far as shape goes if I can get the shape that I'm going for without trimming
that's kind of why I don't trim very much. So you can see here I trimmed the inside and then I went
back and put a swirl on the bottom. The clay was soft enough that I could still do that.
Now you can see I'm wiring the piece off from the bat. Now I'm going to use my sticky bat from
to flip this piece over. Now this is where the tricky part really comes in for trimming these
because two things are happening. You have to center this which you always have to do in trimming
but I also have to level it and so I'm using little strips of my foam paper that I use when
packing and shipping pieces and so I kind of use that as a way to level the piece and then
after I get it leveled so I'm kind of bending over to look at the side of the piece to see if
it's running level and now I'm going to actually center it and you can't really tap center this
because it's sitting on these little pieces of foam paper but you'll see here in a second that
I get it centered good enough that I can start to trim. So there we go we've got it centered up
and I'm going to use my trimming spinner from diamond core tools. So all the tools for trimming
I'm using here are from diamond core tools. I have my sticky bat. This is the extra spall
trimming spinner and then I also have the half dome trimming tool and so that's my favorite one
because then I get a 90 degree angle plus I get the curved side of that one and so I can do
I can do both. So the only part of the bottom of this that I trim that actually has a little bit of
the twisted part to it is right kind of at the you saw me trim it there a second ago at the
very top of the foot or the base of the bowl just to kind of even that up and to get that
angle right there where I come in from the bowl to the foot trim that and so you can see I start
digging down here and then I'll remove the trimming spinner to do the inside of that.
Obviously this is not placed on the wheel with lugs and it's also not in contact with the sticky
part of the bat on every surface so it's a little tricky you can with these they can move a little
bit easier than other pieces that are just sitting right on the sticky bat. So I've got my my left
index finger finger kind of sitting there to try to help and you can see it's even gotten a little
off center already and I have to readjust it because of because of trimming on it but
the bowl itself is already a little wobby sobby so it's not like I have to get a perfect foot on
the bottom but I also don't want it all wonky either. So I'm trying to trim this out and I
don't want to have to pick it up and and check to see how thick it is so I'm just trying to go by
look and feel so that I can trim a good foot on it get that inside of the foot trimmed out so to
get all the weight out of there get a nice looking foot. I did trim a couple others where I did a
little bit more of a rounded foot instead of that sharp angle that's on this one and I actually like
that better because it kind of matched the roundness of the bowl as well so in future ones
that I made since I made this one I did a little bit more of a rounded foot on it and I kind of
like that better but that's kind of all just preference and then instead of signing these I
use my my little button that I put on all my handles kind of my little signature button I use
it in the bottom right in the center of the bottom and that's where now we'll get back to normal speed
on this video as I make a little ball of clay and then use it in the center and then use my
my little stamp that my little homemade stamp to make the
to make that into a button with my signature little
design that's in there so anyway so this is a twisted bowl from throwing and trimming all in
one. I'm getting ready to glaze some of these I was doing some glazing earlier today and so I've
got the idea to glaze the inside of some of these and leave the outside completely raw even in my
gas kiln I'm going to try that and see how some of these look like that but as you can see the
twist looks really cool it's uh like started to rip a little bit but not too much and just turned
out beautiful so give it a shot and let me know how it works for you and we'll see you soon thanks
for watching
