How to Assemble the RYOBI SPEED BENCH Mobile Workstation
"LIKE & SUBSCRIBE for new tool announcements, DIY projects, and more!
Follow along to learn how to properly assemble the RYOBI SPEED BENCH Mobile Workstation!
Compliment your power tools with our wide variety of RYOBI accessories and attachments for any application. From drilling and driving bits to replacement blades, brushes, sand paper and much more. Click the link below to complete your collection! "
#machine #tools
The RYOBI Speedbench Mobile Workstation Assembly Guide.
Step 1. Unpacking. Carefully remove the product and any accessories from the box.
Inspect the product carefully to make sure that no breakage or damage occurred during shipping.
Do not discard the packing material until you have carefully inspected
and satisfactorily operated the product. If any parts are damaged or missing,
please call 1-800-525-2579 for assistance. Tools required for assembly. An adjustable wrench.
Ratchets and sockets 17mm, 13mm, and 8mm. And a Phillips number 2 screwdriver.
Step 2. Attaching the Handle. Place the tabletop face down on a flat, non-marring surface.
Locate the edge of the workstation. Label A. With the attachment bracket at the front of
tabletop, insert handle. Label D on each side simultaneously. Align holes to the handle with
the holes on the frame. Insert the bolt through the holes in the handle and frame. Place a nut
onto the bolt and tighten. Use a Phillips screwdriver and 13mm socket to secure.
Step 3. Aligning the Skid Frame to the Table Frame. Insert the skid frame. Label B into the
table frame. Label A. The rubber feet on the skid frame should be facing up.
Step 4. Attaching the Wheel Frame to the Table Frame. Locate the wheel frame. Label C. Place the
wheel frame in between the two sections of the table frame assembly. The release lever with the
lock icon should be facing up. Align the holes at the top of the wheel frame with the holes on the
inner table frame tubing. Stack two spacers with curved edges facing the tubing and slide to fit
between. Insert the bolt through the holes in the frame, the two spacers, and the wheel frame.
Place a nut onto the bolt and hand tighten. Repeat on the other side. Step 5. Finish Frame Assembly.
Carefully align the holes on the outer section of the table frame and the wheel frame.
Use a bolt on one side to pin the lifted pieces in the proper alignment so that the remaining
hardware can be installed. On the opposite side, stack two spacers with curved edges facing the
tubing and slide along the tubing to fit between. Insert the bolt through the holes in the frame,
the two spacers, and the wheel frame. Place a nut onto the bolt and hand tighten. Carefully remove
the bolt used as a pin. Stack two spacers with curved edges facing the tubing and slide to fit
between. This may require additional adjustments with force. Insert the bolt through the holes in
the frame, the two spacers, and the wheel frame. Helpful hint, you can also place a screwdriver
through the opposite side of the bolt and use it as a guide. Place a nut onto the bolt and hand
tighten. Use a Phillips screwdriver and adjustable wrench to secure. All four connection points with
spacers that were previously hand tightened should be tightened securely. Step 6. Installing the
Wheels. Slide axle bolt through the wheel, washer, and then through the holes in the wheel frame.
Place a nut onto the bolt and tighten. Use a 17mm socket and adjustable wrench to secure.
Repeat the process on the other side. The wheels should spin freely when installed. If they do not,
loosen half a turn on the bolt. Step 7. Installing the Skid Plate. Ensure that the release lever is
in the locked position before rotating the workstation. Carefully lift and rotate the
workstation so the unit is resting on the wheels and the handle. Insert the skid plate, label E,
into the frame. The skid plate should be facing upwards. Align the holes in the skid plate with
the holes in the frame. Insert the wing nut through the holes in the skid plate and the frame.
Tighten to secure. Repeat on the other side. Step 8. Installing the Link Accessory Rails.
Locate the attachment bracket on the tabletop. Align the holes in the link accessory rails with
the holes in the attachment bracket. Insert the screws through the holes in the rail
and the attachment bracket. Place a nut onto the screw and tighten. Use a Phillips screwdriver and
adjustable wrench to secure. The link double organizer bin hangs on the link accessory rails.
Step 9. Relocating Link Accessory Rails. The attachment bracket can be moved around
the edge of the tabletop using the pre-drilled holes provided. Using a Phillips screwdriver,
unscrew the three bolts that hold the attachment bracket to the bottom of the tabletop. Identify
the location of the edge you'd like to install your Link Accessory Rails to. Insert bolts and
tighten to secure in the new location. Now you're all set to start using your Speedbench mobile
workstation. Optional. Installing Miter Saw. You'll need nuts, bolts, and washers, a ratchet
and socket set, an adjustable wrench, and a drill and drill bit. Place the miter saw on top of the
work surface where you'd like it to stay and mark where four feet are. Ensure you are mounting the
miter saw outside the mark no drill area. Take off the miter saw and drill pilot holes where you
previously marked. Place miter saw back on the work surface and insert bolts through the holes
in the miter saw and work surface. Place the nut onto the bolt. Tighten securely with an adjustable
wrench and appropriately sized ratchet and socket. Need additional help? Call RYOBI customer service
at 1-800-525-2579 or visit ryobitools.com