Here’s a great DIY way to get water right at your garden plant’s root zone. This minimizes the use of water because it’s only used right where it’s needed. This GREATLY suppresses the weeds as well.
#irrigation #gardeningtips #dripirrigation
This is our second iteration of this system. The first one was adequate, and we got good results. This new version is much improved, using larger supply and return manifolds, flow balancing valves, and most significantly, a return manifold that makes the setup a “closed-loop.”
Build the setup using standard PVC pipe, fittings, valves, and a garden hose to pipe fitting. We use 1” (25mm) pipe and fittings for the supply and return manifold, and ¾” (19mm) pipe for the laterals that run along the plant rows.
We water a plot of about 200 corn plants in a space about 11’ x 30’ (3.4m x 9m) as well as raised beds that are about 4’ x 8’ (1.2m x 2.4m), We don’t think we’d use this approach for anything much bigger. There are better “off the shelf” products out there for that.
Our spacing for corn is 9” (about 230mm) in a row, with the rows about 30” to 32” (about 800mm) apart. This works well for shading, cultivation, pollination, and wind resistance.
This low-tech system simply uses a high-quality commercial ⅝” (16mm) garden hose attached to one of our hose bibs that delivers about 60 PSI (pounds per square inch) and the hose outputs just under 16 gallons per minute (GPM) or about 950 gallons per hour (GPH). For those using the metric system that would be about 61 liters per minute or 3596 liters per hour.
Water volume needs to be sufficient with this “leaky” system. 1/16” holes (1.6mm) holes are drilled in a straight line along the lateral pipes at the pitch (distance apart) you need for the crops you are growing. If you mix crops and pitches of the holes, balance the water flow using the diversion valves.
You have three methods to adjust the system.
First, hose volume. Too little, and the system will “starve out” before getting water to all the plants. Too much, and you will have joints starting to work apart, as well as too strong of streams of water. You want the water to land within a very short distance from the pipe.
The second is flow balance valves installed in the manifolds. With two on each manifold, we’ve been able to fine-tune the system using only one of them, but if we were mixing crops, then they would be used more.
The third is by first raising sections that are getting too much water. You can do this with blocks of wood, bricks, or squarish rocks. However, with the return manifold, we’ve not had to resort to this, as the system tends to balance itself out well.
Begin by getting all your supplies and parts together, Mark straight lines down the sides of all the pipe parts to use as a reference when drilling and assembling. The printing on the pipes isn’t usually straight and you want water coming out of all the holes in the same plane. The same goes for assembling the tees and elbows on the manifolds.
To get straight lines, tape together 3 or 4 pipes about 4 places along the length. Make sure the batch isn’t twisted but is lying flat. Use a permanent marker to draw lines down the length where the pipes nest next to each other. Cut the tape and you’re ready to go.
Glue the manifolds together for easier storage, setup, and tear-down, but the rest of the system simply pushes together.
Use a 1/16” (1.6 mm) drill bit to drill holes at the pitch (distance apart) you require, always drilling on your reference line.
When making the manifolds, you will have an extra fitting on the supply side because of the hose attachment. So, be sure to assemble the two manifolds side by side to get the tees and elbows to line up so you’ll have nice straight rows, and the system goes together easier.
Assemble the system, and flush out dirt and plastic bits by leaving the return manifold off. Then assemble, and balance the water flow. The wet spots on the plot will also tell you exactly where to plant! I plant a couple of inches to the side of the pipe.
To maintain the system, check joints from time to time, and use your drill bit to clean out clogged holes. Cover the manifolds to delay UV damage (we use mulch) and be sure to disassemble and store the parts out of the sun over the winter.
And, yes, you could add a hose timer to further automate the system!
We are aware that there are various opinions on whether or not to use PVC for safety and health reasons. We are fine with this approach, but that’s your decision.
There are ready-made systems available, along with emitter tapes and the like. We’ve used them, and they work fine, but we like the rigidity of the pipe that helps in the layout of the system as well as bundling it up at season’s end to store until the fun begins all over again!
JUST DO IT YOURSELF!
Instagram: https://www.instagram.com/dirtfarmerj
Facebook: https://www.facebook.com/dirtfarmerjay
hey dirt farmer J here from dirtfarmer
j.com wouldn't it be really handy if you
could create an irrigation system that
would water a moderate size food plot or
maybe even raise beds and you could do
it with simple materials you can find at
the Home Center well this is the right
video for you cuz that's exactly what
we're going to do stay tuned and I'll
show you how we've done it and why
you're going to love
[Music]
it hey dirt farmer J here from
dirtfarmer j.com we love growing our own
produce when we can whether it's in our
raised beds or in a smaller food plot we
have a little Field of Corn that's about
11 by 30t uh you can see Maggie there
greeting us right now that's about 3 and
1 12 M by 9 M for my friends outside the
US but that gives you kind of the size
of the food plot we've got five rows
there where we're growing this corn like
any farmer does you start with a
cultivated field and here you can see
that little food plot that has been
plowed and is ready to go the goal when
we're done with this project is to
create what you see there this grid of
pipes that lay in nice rows in this case
what worked really well for us uh is
five rows three in the center one on
each end gave us five rows uh we were
putting these row distance about 30 to
32 in apart uh which is about 800 mm and
so that works out really well for us the
distance between the corn plants
themselves is 9 in or about
230 uh mm or 23 cm so we found that
works about right some people like to go
larger almost to a foot or whatever it
might be uh that 9in pitch works really
well for us for weed control and so
forth so you start with that bare field
you want to end up with this setup now
something you should be aware of when
you use PVC outside it is not UV
resistant so over a period of time like
you can see here it's just going to
Blacken and
brittle um so what we do is we cover the
exposed areas with Mulch on the headers
uh and the return manifold and all that
sort of thing and uh it's not the rest
of it that's the laterals under the crop
get covered pretty well so they'll last
multiple sessions or Seasons yes we're
aware that some people really are anti-
PVC pH it's toxic it's caus
problems um there is some good science
on both sides of that argument and so
that's a way above my pay grate you need
to make a decision of whether you're
comfortable using that material we are
and if you are hey continue to watch and
we'll tell you how this is done the
first thing you need to do is get all
the lateral pieces of pipe this is the
pipe that's going to run along the rows
of the crop in our case we use 3/4 in or
approximately 19 mm meter pipe uh and it
can be either schedule 20 or schedule 40
uh schedule 20 is a thinner wall
schedule 40 is heavy wall we had
actually a combination of it because
that we had stuff in inventory and we
had to buy some additional pieces we
Blended both types the outside diameter
is the same so all the fittings fit so
either one works really well the
laterals as I call them under the pipes
are that 3/4 19 mm the main manifolds
the supply side and the return on the
the other end the return manifold is
made out of 1 in or 25 mm and in that
case I like to use the heavier gauge the
20 or excuse me 40 a schedule 40 pipe
it's a little bit more robust you're
going to use those manifolds over and
over again for several seasons so make
them robust those sections are also
glued up when I say those sections I
mean the manifolds uh because you're
going to take them out in one piece Stow
them over the winter uh but the pieces
that run down the road row are
pressfit uh you want to be able to take
everything apart and have nothing longer
than 10t and a bucket full of cup Lanes
uh that you can then have ready to go so
when the fun starts all over the
following spring you're ready to go all
right so the first thing we do is get
all those pieces of pipe together as we
said lay it out on our work table made
sure they were clean some of them been
outside or in the barn they're Dusty uh
the ones straight from the store were
clean but wipe them down and the reason
is you're going to go to this next step
of putting reference lines on them and
to do that you need to tape them to uh
together in bundles of four or three uh
and then you're going to use a uh
permanent felt tip marker Sharpie is a
very common brand uh that we use around
here and you're going to put reference
lines that you're going to use to both
assemble your fittings on the manifolds
as well as drilling the holes where the
water is going to come out to feed your
crop or to nourish your crop or whatever
you want to put it moisturize the crop
there we go so what's going to happen if
you do not use a reference line that's
truly straight and you are tempted to
just use the printing that's on the side
of the pipe you're going to be sorely
disappointed and the reason is a lot of
times that's running on a slight spiral
so is it kind of makes its way around
and if you follow that line drilling
holes at this end of the pipe the water
will be coming out the side what you
like it to be doing when it comes out
the side to water um something that's
maybe that far apart and that's about
how far I like to plant things from the
pipe uh you'll have some that are just
arcing very nicely then you'll have
others that are going like this and
you'll have others that are going like
this and others are going the other way
in extreme cases save yourself the
disappointment take this step and how
you get that reference line is simply
bundle them together tape them together
make sure they're not twisting the
bundle lay them on a reference surface
like a big table or work table or
something like that picnic table if you
whatever it is you have and then take
your marker and run down between
wherever the pipe nests together that
joint right in the middle and that'll
give her a reference line to work with
once you've got that the next thing you
need to do is Mark the distances of what
you're going to drill now in our case I
told you we were doing uh the 9 in
roughly
230 met millimeters apart but let's
suppose you're doing melon crops and you
want to grow watermelons or cantaloupe
or Caba or crenchaw or whatever it is
pumpkins and you're going to do those in
Hills then what you're going to do is
not drill holes every 9 in you're going
to batch a little bit of holes let's say
every 5T 6ot whatever the distance is
you prefer to plant those kind of crops
and I would drill more than one hole at
that case CU you are actually irrigating
multiple plants so perhaps you drill
three or four holes with just a little
bit of space between them and that'll um
that'll irrigate that Hill very nicely
so you can make different sets of pipes
for different crops our entire uh plot
was just corn all set at that pitch but
this is the nice thing about this you
can make it whatever distance you want
just use that reference line so again
the emitter effect of the water coming
out it all lands in the same place and
um and makes it really easy to get
everything to irrigate evenly so once
you have those distances marked I use a
square across them then the next thing
is you're going to drill them now what I
use is a 116 inch bit just a regular
highspeed steel bit and that happens to
be about one 1 and 1/2 mm that's
probably not the size for my friends
around the world uh but it translates
roughly to 1 and 12 1.6 mm it's a very
small bit and the idea is when you're
drilling pipe if this is the curvature
of the pipe you want the bit to go
straight in okay straight in don't drill
at an angle that'll actually affect the
trajectory of the water that comes out
so the goal and you don't have to be
perfect but the goal is to get as many
of those holes drill perpendicular to
the surface of the curvature of that
pipe so that you get that great
consistent um trajectory coming out all
the way along that lateral now at this
point it's time for a drilling party and
uh you may think this is sped up but no
it's just normal speed it's uh it's how
fast I work around here yeah uh and if
you believe that I've got some deals I'd
like to sell you but anyway so we drill
out all those holes and now at this
point um you now have that section down
it is time now to move on to the
manifolds the main supplies again
they're larger to 25% lar 1/3 larger one
and a3d uh they're from 3/4 to 1 in and
in uh Imperial size uh and at that point
I go ahead and mark the sides just like
I did the other and I Mark reference
lines on all the fittings here's a power
tip for you and why it's really
important you want all of those t's to
come out and wherever the connectors are
elbows on them to come out in the same
plane if you don't then the pipe is
coming in at an angle on one coming in
straight on another it just really gets
tough to put the whole system together
so if you can keep everything flat it'll
really help it go together and so I just
lay everything out go ahead and do my
distances put it together now because
the supply side has an extra T where uh
the hose connection is going to come in
that changes the overall length of that
manifold compared to the return one on
the other end of the field so lay them
side by side and make sure that those
joints or those uh fittings line up and
if you look close you can actually see I
had to throw in a little bit of a extra
piece uh cuz I wasn't thinking this way
I'm just warning you about it uh to get
it all there and it really made a
difference when we assembled this unit
in the field now if you're this far
you're almost home because now you've
glued up the the supply manifold the
return manifold I put in different
valves in it a couple there uh and I'll
talk about that in a moment you only
have three ways to control water on this
so these valves are one of those that if
you get an imbalance you have a low spot
the water diverts a weird way or perhaps
you have mixed crops in the same way and
one area is really hogging the water and
you want to choke the water back that to
reserve pressure for another area that
needs it these valves and the manifold
allow you to balance them so that's
number one and I'll tell you about the
other two in just a moment now you've
now got the
manifolds yeah here you can see we just
took one of the manifolds out laid it in
the field and then started assembling
everything doing a rough estimate of
where the holes were lined up putting
couplings together pressing everything
together and even though it doesn't
really show it the first thing we did
though is not put the other manifold the
one furthest away from the supply the
return manifold on and we simply ran
water into the system why got to flush
out all those little plastic chips and
dirt that may have accumulated because
if you don't they will find their way
out the holes plug the holes and you'll
end up with inconsistent water so take
the time to to rinse it out and even
when you do first Supply water to it
with the cant you're probably going to
have a few that get little plugs just
use the drill bit that you drilled it
with to go through and maintain those
holes and get them open up the same
amount they are now here you can see uh
the whole uh system assembled on that
plot that we have uh earlier in the
season this season and what we did then
at that point is go ahead and turn on
the water and uh what you're doing at
this point is a couple things one you're
seeing is the water balanced or you're
getting a pretty even delivery ac across
the system if you have a really strong
downhill field it's going to tend to
deliver more to the downhills side you
may have to adjust some things however
we have found and this was due to
several viewers that wrote in I want to
give credit where credit's due it said
that first version of um irrigation
system you did would work a lot better
if it was a closed loop and there was a
return manifold you know what they were
right it really change this and pretty
much there was only one slight um uh
slight adjustment on one of the valves
to get everything to run pretty evenly
so valves are one the second thing is to
raise or lower the system if an area is
really delivering a lot of water in a
low spot then set set the laterals or
the the um manifold on pieces of brick
or angular stone or blocks of wood or
something to make the water have to work
harder so to speak to get to that area
and actually deliver out more before it
gets to that area that's one way uh
actually the second way you got valves
raising and lowering uh it's always
easier to raise by the way than lower
lowering means digging down and the
third one um is just simply volume of
water now one of the things I get asked
a lot at this point is well how much
water do you guys have uh what how much
water do you need well you need a fair
amount on this and the reason is it's a
very leaky system it's not Hightech
You're simply getting water to go um
where you want it to go right at the
base of the plants by making it leak
there so to speak by drilling these
holes so it's not super Hightech but it
does take sufficient water to do it now
to let you know what we have we did a
study on uh or actually tested this out
through our well pressure have about 60
lb per square in uh 60
PSI um this hose when it's opened up
full blast can deliver up to about right
at 16 gallons per minute uh that's a
pretty strong blast we have some really
good pressure out of our own well and
then so that translates to about um
950 gallons per hour for my friends that
use uh liters that's 61 lers roughly a
minute and about 3600 L an hour so we
put out some Fair pressure if you've got
a really low or very small supply line
to this it may not work for you or
you'll have to do smaller blocks to not
over extend the capability of your water
system to deliver okay so once you've
got this all together the next thing you
do then while you're testing it here's a
really cool thing about this system you
go ahead and get everything adjusted so
you're getting this gentle AR all off I
like to do all off to the left as I walk
down so it's always delivering to the
correct side I want the water to hit
about that far apart uh how's that face
width right there or maybe the width of
thumb to finger something like that
again this isn't uh precise uh and the
reason is you want a little distance of
where the plant or the crop's going to
come up for
cultivation but you first turn on the
water um and then what it does is really
cool it puts these water marks all over
the field where the water is going to
liver and now you know where to plant so
alls I do is go along and plant the corn
about 4 Ines away to the left of the
thing all the way down and that water
lands beautifully right there here you
can see this beautiful Little Seedling
that's just getting water right where it
needs to be and even the adult plants
this amount of water run for 10 15
minutes uh every other day even where we
live in the high desert west of the
United States and with some roasty days
the Corn's thriving and we haven't had
no dress at all we're going to have some
great eating of the sweet corn it's that
bolor sweet corn so when you get this
all put together you're going to have
some great results it'll continue to
grow and you can see right here early on
a crop the young crop starting to to pop
up uh and it never slowed down now let
me tell you about weeds very quickly if
you may be looking at some of this uh
like here is a great uh shot that just
shows you looking from the crown of the
Corn kind of looking down as you go down
into the canopy and then you can see the
one of the irrigation lines here uh when
the uh crop this is taken just um about
a week ago uh and the crop is ready to
harvest in about 3 weeks uh so uh corn
is pretty mature it's tasseling right
now and all that right now um when you
look down in there uh you might be real
critical and say man you have a few
weeds down there yeah I do if I'm like
you know I suspect you and I are alike
we got a lot of things to do one of the
things Pig weed on these kind of crops
and other weed like that put out
literally millions of seed in the crop
of plot area and the first thing I
actually do is sprinkle the plot at the
beginning before that's the reason you
saw that first picture wet because
because what happens after I plant it
and before the uh corn comes up cuz it's
planted 3/4 of an inch inch deep
something that couple centimeters what
happens is you get this incredible flush
of green I mean literally that food plot
right there probably had um
500,000 it was a Green carpet of all of
that weed blown or uh wind blown seed
from pigweed so I go ahead
um ho it off real quickly uh you can
flame it off if you protect that area or
you could flame it all off first before
you put down the area but kill off 90%
of the weeds you're still going to get a
second flush of weeds at that point I
hand cultivate them and I do that a
couple times also I let some of that pig
Weed grow because when it's young before
it heads out or chickens love it they
think it's a salad so I harvest out of
the road those tender plants that are
maybe you know this tall uh and give
them the chickens and they snap them up
but as the crop grows and it starts to
shade now though that weed growth really
slows down as you can see in the bottom
yeah there's some weeds is it enough to
affect hering no am I going to lose
sleep
no judge me if you wish but that's just
the tradeoffs there well this is a great
system that I think you're going to
enjoy now for those of you who think
that's a lot of work yep there are other
systems out there you can buy them
readymade where they're already
pre-space uh you connect them together
but if you want to do it yourself and
you want a system that's tangible you
can knock down then this is a good way
to go and simply make sure you put away
the system at the end of every year so
you get many seasons use out of it and
protect it from that um that UV
degradation that happens over the period
of time well we love having great Tools
around here that make our homesteading
life a lot easier and one that you
should really check out is the Str
str22 super tough Barn manure rake we
love this rake it's lightweight it's got
aluminum handle very flexible but strong
head uh U and I'll tell you what it's
worth every cent that you pay for it
take a look at it here I think you're
going to like it while you're at it also
check out this other video from our
catalog that YouTube thinks is perfect
for your interest and we think you're
going to love it too hey until the next
time this is dirtfarmer J from
dirtfarmer j.com getting ready to enjoy
some great eating of sweet corn from our
food plot