Building a Self Watering Garden Container

DirtFarmerJay
309 followers
33 Video Views·Jul 28, 2013
This is the first of a series of videos geared specifically to "urban gardeners" - those of you that live in apartments, condos or anywhere where you do not have a plot of land to plant a garden in. You, too, can have the fulfilling experience of enjoying the "fruits of your labor" by using one or all of the techniques that Dirt Farmer Jay will show you. This first technique is a self watering container that can be used for any single-plant vegetable or ornamental. The self watering container is also great for extremely hot or arid climates.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
You know, some of you have written in and given us a call and said we love the fact
that you are all about self-reliance, growing your own food, doing gardening.
The problem is we don't have two acres, three acres, five acres, which you guys have.
We don't even have a little bitty plot.
I live in a condo or downtown, only have a balcony, or live in a place where there is
no open ground whatsoever or have very limited open ground.
So how do I get into the enjoyment, the healthiness, and the self-reliance of raising some of my
own food?
To you, my friends, this is one of a series of six to ten different methodologies you
can use to become self-reliant for your food source or at least greatly diminish your dependence
on having to go to the store to pick up some of these things.
Besides, it's just a great amount of fun and if you've got little ones in your life, if
you're a grandparent or you're raising little ones at home, a tomato that a little kid raised
or picked themselves always tastes better, okay?
So let's get started.
The first in our series is a self-watering container.
This is known by its acronym, SWC.
As you can see, it uses commonly available items.
This happens to be a couple of homer buckets from the Home Depot, there's a little bit
of three-quarter inch PVC pipe, there's some soil mix and so forth.
The really cool thing about an SWC is that you get to water perhaps once a week, that's
all you need to do.
Number two, it's a closed system so it makes fertilizer only in the top ring up in the
top.
Number three, it creates a very robust root system in here that I'll show you here in
just a second as well.
So this really works out well and here is a great thing for those of you that are in
the desert southwest, for instance, Las Vegas, Tucson, Phoenix, where you get some really
hot, droughty areas, a lot of wind moving on.
This really helps conserve moisture, allows the plant to thrive even in those kind of
situations because there's plenty of moisture as the plant needs it.
There's the soil, potting soil, and you would add fertilizer just by putting a ring around
here, putting fertilizer, this has been fertilized once about four or five weeks ago, but you
can see that there's plenty of moisture in this.
It's not really wet, it's wicking it from the bottom and I have a surprise for you in
a moment here.
Now, I'm going to put this back on, I'm not going to snap it on, but here is, we're going
to pull this out and when I do so, you can see the chamber that's on the bottom and that
chamber, and this is quite heavy, so I'm going to set it right there.
That chamber at the bottom that you just saw is what transfers moisture across to the bottom
of this here.
It wicks in from the bottom reservoir into this and feeds the bottom of this here and
as you can see, this tomato plant is doing quite well.
Look at all the roots here.
We have a root structure that's filling this whole bucket.
Now, let's go and look at the supplies that you need to build this very container.
First of all, I want to give credit where credit is due.
This is actually a plan out of the urban homestead and this is in about page 20.
There's a great diagram, so this is a great start, get the book, the urban homestead.
Secondly, other tools you'll need, you'll need a hacksaw, you'll need a PVC pipe cutter,
you'll need a Sharpie pen, a paddle bit that's about a 1-1-8, some kind of cut out saw, a
stab saw, a tape measure, a drill motor that allows you to put in a couple different bits,
a large bag of potting soil, and for the wicking chamber, you're going to need a yogurt cup,
something like this.
Okay?
All right, that's our basics.
Let's get going.
The first thing we're going to do is we're going to cut the fill tube.
You need to cut a tube about 24 inches in length, and I'm going to cut it at an angle.
The reason for that is that if you put it flat and the fill tube just lands flat on
the bottom of the bucket, the water's going to have a difficult time coming out.
If you cut it on a slant, when you fill in the water from the top, it'll come down, splash
out the sideways just fine without backfilling the tube, and the drill hole on the side of
the bucket stops it from overfilling.
So here we go.
We're just going to cut at an angle on this.
Okay.
So then, that's going to be your fill tube.
The second thing you need to do, go ahead and mark where the fill hole goes or the overflow
hole goes in the second one, and here's how you do that.
You put one bucket inside the other, and you hold it up to the light, and you can see the
line right there and say, okay, that's where it is.
Now that we know where our mark is, you can actually see the mark through here, we're
just going to drill a hole to the side.
There we go.
I use about a quarter to five-sixteenths of a brad point for that.
The first bucket's completely done.
There you go.
As you can see from the inside, no matter how much water you put in, it's always going
to leak down to that level and then level out and therefore create that air gap between
the top and bottom bucket.
All right.
Now, here's the more extensive work that needs to be done.
I pre-marked this just a little bit, and I know that you want this cup not to come
all the way through, so I just drew the outside diameter of the cup, and I'm actually going
to use it as a guideline to estimate where I'm going to cut that.
You don't have to be super, super accurate in all this.
That's part of the fun on this is that you can just kind of go at it, and what I do is
I take the drill right here and get a couple starter holes.
Okay.
I learned real quick as I was cutting with this, this saw only works moderately well.
It will cut the plastic okay, but here's part of the problem.
It's so wide that it can't turn, so I've switched, and now I'm going to go ahead and use this.
You probably have one of these here, and you can see you can plunge this cut in.
Just be careful where the knife blade goes.
There you go.
See how it's plunging in?
Okay, so now I've got the hole cut out, and the first attempt I cut, it was too small,
so what I had to do was just trim it out until it fit the cup correctly, and so here we go.
Here's the cup, and we're just going to let it hang on the lip of the bucket into the
second bucket.
This can't protrude beyond three inches below, so I'm going to just push that through, and
as you can see, that's just about right.
And meanwhile, what we need to do is put a roll of holes all the way around this.
It allows the moisture that gets pulled up and then excess to drip back into the container
down below.
So here we go.
You know it's right here that I did not put one of the holes here.
The reason for that is that we need to put the fill tube down to the bottom, so I'm going
to use a 1-1⁸ inch paddle bit.
I'm just going to put it in this open area here where there's nothing close to it, take
that through, and let it go.
There we go.
Now, we put, just to test it, we put that bucket inside there.
You can see that that tube is going to go right in the bottom, I'm going to tilt it
right that way.
That's how that tube is going to go.
There's a couple more things you need to do.
Number one, we need to put a matching hole for the fill tube to be held in place, and
how you do that is simply using the same 1-1⁸ inch paddle bit, you're going to put
it right out near the edge over here.
So you don't have to be perfect again, you just simply, there you go.
What it does is just like that, you're going to rotate that around and you can see that
that would put a fill, you can cut it a little closer if you want.
Now, what about where the plant goes?
Well, that's our next step.
What I do is I use the yogurt cup itself as the marker.
Now, depending on what you're going to plant in it, I would say keep a smaller hole simply
because one of the main purposes of the lid is to reduce evaporation or retain moisture.
So the bigger the opening you put across the top, the more loss of moisture you're going
to have at the top.
You're trying to create somewhat of a closed system here.
So you can again eyeball this, I just simply use the bottom part of it, mark around, and
what we're going to do here is just...
Okay, we essentially have the top of our bucket except for the wicking chamber done.
So right now, that's where the plant's going to be.
Now, one other option that you might be interested in here may help you a bit, and that is to
split the lid.
If you like, and if you have some way to cleanly cut this, you can cut sideways right across
the top.
Cut that in half, and that allows you to snap it on after you put a plant.
We're going to turn our attention to the wicking chamber.
Remember, it's called a wicking chamber because it's suspended into the water solution below.
It pulls in water and irrigate by diffusion, it'll pull it up into everything here.
So here we go.
The only thing we're going to do here is drill a series of holes around the side, not on
the bottom.
The reason you don't want to do in the bottom is that that would have the soil have a tendency
to drop out of it.
So simply all you're going to do is use this and just...
So now we have the makings of our wicking chamber, real simple, okay?
Top bucket, put this through, wedge it in.
What you're going to do is put this into there.
Second thing you're going to do is put your fill tube, remember to put the angled end
to the bottom.
So you're going to line that up in the hole in the bottom, it's now standing and hitting
the bottom bucket.
You're going to go ahead and fill this with potting soil to the same height that you saw
over here on this dude right here, okay?
You're going to build it right up to here, move this to where now it is held in.
Go ahead and plant your plant, put this over, or split the lid and snap it on both sides.
You can put a little ring of fertilizer around the side, do not fertilize the plant directly,
just put it around here because the moisture will move the fertilizer as it's needed.
So what we're going to do here is put this on, get your plant in there, put your support
sticks out the top right there.
And then what you're going to do is go ahead and fill up the bottom of water, saturate
this a little bit as you do it, get it moist so you're not putting a moist plant ball into
a dry soil mix, okay?
And at this point, you now have a self-watering container.
Put it on a somewhat level area where it's well-supported.
Another great thing about these is you can move them around.
If you've got an area that gets some mild sun or moderate sun in the morning, the plant's
okay out there, but later on it's a real roaster, you can move the plant in under shade, give
it the best of both worlds, some bright shade, reflect it light off or something else.
Well, as I said, this is the first in many series on techniques that we're going to show
you, the urban gardener, how to make the most of your yard so that you can grow more of
your own produce, the things you enjoy in life.
Until the next time, I'm Dirk Farmer Jay, DirkFarmerJay.com.
The only place you want the water to transfer is the little basket that's hanging down that
will perforate that is full of soil.
So that's the purpose of this.
So the overflow always creates an air gap no matter how full you fill the fill tube.
So what we're going to do is go ahead...
