Lecture 18 - Transceiver Architecture - V

IIT Roorkee July 201
61 followers
Jan 25, 2024
Concepts Covered: Weaver Architecture, Low IF Receivers, Polyphase Filters
[Music]
[Music]
uh welcome to RF trans design course uh
we are discussing the trans
architectures in last class we have
discussed the Hilbert transform and
heartley architecture and how we can use
a hilber transform in order to reject
the image so now one of the another
class of the uh image reject receiver is
a uh viewer architecture so we'll see
the Vier architecture in
detail so the difference between uh Vier
architecture and heartly architecture is
in heartly we are adding a 0 or 90°
phase shift by using any rccr filter and
uh that we can also do at the base band
side however in weer architecture we are
doing the uh down conversion two times
so it is a uh version of super Hine
version where we are converting the
signal two times uh down conversion and
uh we are adding the 90° phe shift by
doing the same quadrature down
conversion again so it will add the uh
90° pH shift so up to this point x A and
B uh we have already derived how the
signal will uh be down converted so if
we try to see the
trigonometrically at C and D how the
signal will look like so again Omega L1
and Omega L2 so here Omega 1
is Omega L1 and Omega 2 is Omega L 2 so
and Omega C is a input RF
frequency so this is Omega C minus Omega
1 Omega 1 minus Omega 2 now because we
are doing the multiplication two times
cos Omega l 1 and cos Omega L2 it is a a
signal divide by 4 and there is some
phase of the
signal similarly there is another
component which is the image minus Omega
1 minus Omega 2 now when we uh multiply
Omega with Omega L2 what is happening
that uh its positive term is also coming
and negative term is also coming so this
is a uh Omega 1 minus Omega 2 that is a
negative term and this is a positive
term that is Omega C minus Omega 1 +
Omega 2 Omega minus Omega 1 + Omega 2 so
same thing at xdt uh we are multiplying
with sin Omega l t so the sign will
change as explained in the Hilbert
transform that minus a signal by 4 cos
Omega c - Omega 1 - Omega 2 + 5 signal
minus a i IM by 4 cos I Omega M - Omega
1 - Omega 2 so
and this is a positive term now if we
take one example we will understand that
how this positive term can be filtered
out so if your Omega carrier frequency
let's say it is a 1,000
mahz and your Omega 1 let's say that is
600
mahz and Omega 2 is 300
MHz so what will happen that the what is
the Omega Omega
if is equal to Omega C minus Omega 1
minus Omega 2 that is a
100 mahz now if we consider Omega C
minus Omega 1 plus Omega 2 so that is
400 plus uh 300 so that will come this
term will come
around
700 mahz and same thing this will be
minus so that is the part of image so
this will be too far from 100 mahz so
that we can easily filter out so we can
neglect this two term from here here and
from here so now only the term four
terms are remain that is a two term at
XC that is Omega cus Omega 1 - Omega 2 t
+ Pi signal and this is the image now
because of the quadrature multiplication
there is a minus sign here that is a uh
minus a signal 4 cos Omega C minus Omega
2 so if we just uh
considered this one of the
frequency uh here what what we are
trying to do when when we do the sub
subtraction of this uh one of the term
will be canceled out that is the image
this image will be cancel out and that
uh this signal will remain here so this
is how the weer architecture will work
so the difference only is here we are
doing a two times uh down conversion
that it is cos Omega L 1T and cos Omega
L 2T again quadrature sin Omega L1 T and
sin Omega L 2T so uh the difference is
the by using a two times multiplication
we are rejecting the
image now another important class of uh
receiver architecture is a low if
receiver so what exactly low if receiver
is the if of
frequency is around the uh frequency of
the bandwidth it
is bandwidth of your signal so what will
happen the direct conversion of 200 Kil
Desir channel to Zer if May
significantly corrupt the signal by 1X F
noise so in direct conversion what is
the issue that we have a uh problem of
the DC offset we have a problem of
leakage we have a problem of 1x F noise
now all this problem can be solved if we
have a sufficient means not too much if
but sufficient if so that it will uh
down convert the signal and again we can
use the uh on chip filtering so that uh
the signal can be easily filtered out
and we can also reject the image so how
exactly the uh L of receiver will work
so here this is the carrier frequency
and at half of the L means half of the
bandwidth so this is a half of the B
bandwidth there is a l uh signal will be
applied and when this signal is down
converted the there is a signal will be
here and this is the image so this will
be the
image
and on one side there is a signal so you
can easily uh filter out your signal on
chip so if you consider the GSM standard
requires that a receiver tolerate an
adjacent Channel only 90b above the
desired channel so if there is a
adjacent Channel just after
this this is the adjacent Channel then
this image will this is a
image means on other side there is a
image and that image will come here so
what what we are interested to remove
this
image and how how what is the advantage
of this that only 9 DB you need to
reject and you can use a simple image
reject receiver which can provide a 30
DB let's say if image rejection uh ratio
is a 30 DB the image remains 20 DB below
the signal so you can easily uh reject
the image by uh here here it is
90b adjacent channel uh only 90 DB above
the so that you can easily reject by
using the uh any image reject uh
filter so uh this low architecture it
has
a combination of
rodine and
homod so what are the advantage of Hine
that it is more accurate and then homine
what is the advantage it is easily on
cheap you can make now this architecture
lowf architecture you can easily make on
chip and you can filter out your signal
on chip and the problem of image there
is a because it is a Hine structure the
problem of image can easily be solved if
you have a sufficient image rejection
ratio by using the image reject filters
so uh advantage of homine and rodine
both you can combine in low if and this
is a very popular architecture uh in
many uh receivers that are employed so
and it it's provide a very good
receptivity and even you can do the
modul down conversion and the base band
you convert to the digital and you can
reject the image now for rejection of
image one of the widely used structure
that is a uh polyphase filter so we'll
see the how the polyphase filter
works so in order to understand the
polyphase filter it it is better we uh
first understand how the RC will behave
if you give the different signal so if
there is a V1 signal you are applying at
the this is a RC filter now if you are
applying a V1 signal at this node and V1
V2 signal at this node the V out at this
node by using KCl you can easily get
this equation what is the V out V out is
equal to V1 + R1 C1 s V2 / by R1 C1 s +
V1 that you can easily get if if you
consider this node as a v out you can
write V out minus V1 by
R1 plus v out Min - V2 by 1 by SC is
equal to
0 then what if you take this on this
side V
out minus
V1 by
R1 equal to V2
minus V out by 1 by S so if we take R1
on this side what we will get V
out -
V1 into
R1 C R1
C1 into
s V2
minus V out if I will take v v out on
this side that is V
out 1
+ R1 C1 s and then what you will get V1
+ V2 R1
C1 s so same same thing this is the same
equation which is a written
here so now we will take a two case that
what kind of voltage we apply mean
because when we are using a image we
have already seen there is a r+ means I
+ JQ so there is a uh imaginary part is
going to come there in the image and how
we can use that to reject
how you can use R R1 C1 filter RC filter
to reject the
image so the case one what case one says
that if I have a V2 at this point this
V2 if we will use the V2 which is equal
to minus Z V1 and if V1 is a same as a
V1 so in this equation what we'll do is
write V2 here V2 is equal to minus J V1
already SJ Omega is already there so
what you will get V1 into R1 C1 Omega +
1/ by J R1 C1 Omega because s is
replaced with J Omega here and if I will
if we consider the Omega frequency which
is r c inverse uh that is R1 C1 inverse
then we will get 2 V1 by because this is
this will be the one this will also one
then 2 V1 by 1 + a it is nothing but a
V1 into 1 -
J if we write it down the amplitude of
this it is < tk2 V1 and the phase is
-45° so what it says that if you have a
on one side there is a uh V1 voltage and
the another side of the filter there is
a j minus J V1 that is a then you will
get the so this is a minus V2 which is
minus J V1 and this is a V1 the
resultant voltage is V out so here you
what is happening that we are getting a
v out which is a combination of V1 and
minus J V1
now we'll try we will do the another
case if it is a
positive so uh I
will try to this so here in the second
case instead of minus J V1 we are giving
plus J V1 and then we if if V2 is a plus
J V1 that is a negative Hut so uh and
then in this negative h but when we
applied if your Omega is equal to R1 C1
inverse your V out in this case because
this is a 1 - 1 + 1 this will be cancel
out your V out is just a zero so what
what is the conclusion that if your V1
and minus Z V1 uh if you applied the
voltage uh V1 and minus a V1 on other
side your resultant is the V out however
if you have a uh negative HB butt that
is a plus J V1 then you will have the
zero output now we will try to apply
this uh analogy or this understanding to
the actual uh receiver architecture and
how we can reject the
image so if we extend the topology of
previous figure V1 and minus C V1 are
are available in differential form and
we can construct a image reject receiver
so in this example what what if you have
a plus V1 and vs2 which is minus Z V1 so
this is a plus V1 and minus Z V1 you
have a resultant output is like this and
but if you have opposite if this is a
minus V1 and plus a V1 then Only You Are
changing the polarity of V1 to minus V1
and this polarity of minus Z V1 is is a
plus Z J V1 then you will have a v
out2 so if we try to apply this to the
image so this is a quadr down
converter we we all know that if you
multiply with cos Omega L what you will
get V signal plus v there is no any
phase uh change change will
happen minus V signal minus V IM this
what we will get when we multiply with
cos Omega l so here only amplitude is
considered so plus v signal and plus v
because we have done uh analysis of
amplitude in the uh last slide now if uh
when you apply with the sin Omega L
there is a plus JV signal minus JV
so the PO polarity of image will change
and here so this polarity of image we
also seen graphically in the while
discussing the hbert transform and here
polarity of this is change that is minus
J V signal plus J V so here it is a
positive and negative and then there is
a plus j v i now we'll try that how it
will be cancelling out the uh
image and we are getting the signal so
if you take a first case this is the
first
case uh that your signal is at one side
of R1 is a v
signal so this is a v signal
R1 then there is a capacitor
C1 and on other side what you have right
now we are considering on the signal
only signal and on other side side you
have a
plus g v
signal so if you have a uh V signal and
plus JV
signal so what we have done V1 and plus
a v
signal here when you apply V signal and
plus JV signal what will happen you will
have
oh uh here there is a minus
C so there is a plus plus v signal and
here because this is coming from this
side it is minus J V signal so always
remember that this is a uh this is a 0
Dee face shift this is a 180° phe shift
this is uh uh one is a 90 so one is this
is a 90 and this is a
270 so here this is connected to minus J
V signal so I will rewrite it is minus J
V signal so what will be the V
out this is a plus V1 minus J V1 so you
will get here the V out which is a
portion of the V signal which is a 45° f
shifter now we take another case you
have a image V so now we have a
image if you will consider other color
that is a v i and that is a
plus J
V so we we already have seen that if V
is
there and plus J uh means the voltage is
a negative HB transform then your output
is
zero so here your output is coming to be
zero because and your image is a cancel
out similarly when you uh do the same
thing here only the sign will change so
this is a minus V signal
and uh this is a minus V
signal and plus
plus JB signal if you do the same thing
uh in this equation if you use the same
uh thing with this equation only the
difference is this V out will be on
other side but it is going to give you
the V out2 like this so you will get the
V out2 which is a signal which is a part
of the signal now what will happen with
the image for image you will get a
Min uh what is the minus v
i and then the polarity is both same
minus the V so if the polarity both are
same here also positive positive here
negative negative that means it will be
zero and that we can easily get from
this
equation and R1 your R1 C1 is equal to
the your
frequency uh 1 by
Omega so I I hope it is clear to all of
you that uh how we are we can able to
reject the image and con construct so it
is a uh positive uh construction for the
signal and then there is a uh image that
we are uh removing by using this
architecture and this is called the
image reject receiver by using a
polyphase filter so this is nothing but
a polyphase filter which are adding the
various phases we can also extend these
to the four
phases
so instead of two stage only we can also
make a sequence isometric polyphase
filter
and in that what we need to give so on
one side there is a voltage V1 on
another side there is a voltage that is
minus J V1 so this this is a V1 then
this is a minus J V1 again there is a
plus J V1 so V1 and plus J V1 and
then plus J V1 and minus V1 so if you
consider this is a
0° this is a 90° this is a
180° and this is a
270° that are the phase shift so this is
a 0
990 so we can also write in terms of the
pH diagram 180 and
270 so if you and this is also called
sequence asymmetric polyphase filter and
since the signal and the image arri at
the input with with the different
sequences one is passed to the output
and other will be
suppressed so same thing will be applied
at V out2 uh one will be uh means your
signal will be coming as a v out 1 v
out2 v Out 3 so this is
a v out
1 we out 2 we Out 3 and we out 4
that are the four output that you will
get by using this and uh we we can
extend this to the another example where
how the image can be cancelled out by RC
so the only difference is V out1 and V
out2 you will have output at
R1
so this is at output R1 and here also
output at
R2 that is V1 and minus V1 so
here you will have a this is a positive
signal and then this is a negative
signal so this will be
considered this is 0 and
180 and then this is a 90 and
270 so in order to generate the four
phases you need a quadrature mixer
so this mixer will have a 0 180 and 90
270 when you apply the sin Omega l
t so same thing we we can also analyze
with this here when you get
the uh when you have the signal which is
uh 1 2 3 4 that is a v signal and only
uh what what this is doing that
uh here when you are using a polyphase
filter that at that time this signal is
rotated one uh 45° clockwise so this is
a clockwise
rotation
45° and here it is rotated
anticlockwise
and it is rejected so here uh there is a
clockwise at the
output there is a clockwise it is uh
transferring from here to here and then
there is a anti uh for the image it is a
anticlockwise so this is a output which
is transferred from here to here that is
a clockwise however in image it is a
anticlockwise and this is the way the
image will be rejected and also make
sure that here there is
a uh the at this V out3 and V out 4
there is a change in the C3 R3 how we
have connected so uh don't confuse while
connecting you should not connect R1 R2
R3 R4 C1 C2 C3 C4 then you cannot cancel
at V out3 and V out 4 you need to
Interchange because your phase are
changing so this is easily be
constructed R1 is connected to C1 again
R is connected to C and we are going to
give the input at one side and output we
are going to get on the other
side so this is how this polyphase
Filter
Works so uh let's say in uh the previous
example both the case what we have
considered Ed is Omega which is not
equal to rc inverse which is equal to rc
inverse but let's say if your Omega is
not equal to rc inverse then what will
happen so in that case if we try to add
the Omega R1 C1 inverse plus Delta Omega
so if there is some change in the
frequency that is a Delta change then
what will happen that we have a v out
magnitude means is given by this uh
root2 V signal and this there is a minus
10 inverse 1 + r c Delta Omega this is a
v out and then there is a change in the
uh Angle now this RC Delta Omega by 2
and RC Delta Omega which will tell us
that how much so this is a
actual when we have considered the ideal
RC but due to the change so so there is
a phase shift which will happen from
that is RC Delta Omega by 2 so in in 5x4
plus RC Delta Omega by 2 and there is a
change in the phase as well change in
the amplitude as well so there is a uh
this what will happen that when you
consider the
image a small portion because of this
mismatch because of this uh change in
the phase and this some of the portion
small portion of image will also appear
in the output and that is why you don't
have the uh full rejection of the image
and you need to consider the image
reject ratio so be how much image that
we are rejecting by using this uh e
polyas filter that is a uh we can
quantify and we have already seen in the
heartly architecture that is a image
reject ratio that is IM input uh signal
to image by output signal to image uh
ratio so that uh will be uh increase if
we don't have that much variation in RC
but in reality we can never achieve the
complete rejection but uh 20 30 or 35 DB
we can get by using a RC polyas filter
RC polyas filter has a many application
it is also used in quadrature generation
and various application and it can also
be used as a image reject receiver uh in
the image reject receiver architecture
uh thank you we'll continue about the
receiver architecture and also we will
discuss about the transmitter
architecture in the next class
[Music]
a
