Lecture 20 - Transceiver Architecture - VII

IIT Roorkee July 201
61 followers
Jan 25, 2024
Concepts Covered: Direct Conversion Transmitter, Modern Direct Conversion Transmitter, Heterodyne Transmitter, OOK Transmitter.
[Music]
[Music]
welcome to Arab transer design course we
are discussing about transceiver
architectures and in last class we have
summarized all the receiver architecture
and now we will uh go forward for the uh
transmitter architecture so initial uh
uh difference I already discussed the
difference between transmitter and
receiver so the basic transmitter means
you cannot uh whatever the what are
whatever the part we we have discussed
in the receiver architecture same we can
uh same architecture we can also use for
transmitter so one of the widely used uh
transmitter architecture is a direct
direct conversion transmitters uh we
will discuss about direct conversion
transmitter so in direct conversion
transmitter same as your
Omega
Omega l
is equal to Omega RF so here the
difference between the RF transmitter
and receiver is that as discussed in the
last class here up conversion will
happen so the base band signal will be
up converted to the RF frequency and the
L will be applied and uh here uh because
it is a direct conversion transmitter we
use a i in means quadrature modulation
so quadrature multiplication will will
do and then there is a requirement of
power amplifier and matching Network so
uh for transmitter design the most
important part is a power
amplifier so this is a very
important uh component of a
transmitter so what are the issues in
the direct conversion transmitter one of
the issue in direct conversion
transmitter is a IQ mismatch we have
already seen the IQ mismatch in the uh
direct conversion receiver receiver also
here the problem is if there is a change
I and Q if there is a change in the
phase of L or the change in the pH uh
change of the amplitude then there is a
unwanted side Bend will occur and that
unwanted Side Band divided by The Wanted
sideband that will give us the uh IQ
mismatch uh ratio so that is uh
generally consider between unwanted side
Bend divide by The Wanted side
Bend and here Epsilon so this is the
same equation that we have discussed for
the even image rejection Ratio or even
the uh we have discussed for IQ mismatch
uh this is a Epsilon is a amplitude
mismatch and Theta is a phase mismatch
So based on phase and amplitude mismatch
we can have a uh IQ mismatch so this is
one of the issue that needs to be
careful and how how can we get rid of
this we should have a a good uh design
of sensitizer or PL which can generate
the quadrature COS and sign which has
not that much variation in the amplitude
and
phase another important uh
parameters uh that we need to understand
that is a carrier leakage so how the
carrier leakage occur so if if we write
the V
out if you write the V out and that will
be given
by if this is a message signal
Mt cos
5 plus v offset
1 that and cos Omega
CT
minus again there is a message signal
sin
5 + V offset 2 into sin Omega CT
so how this V obset in this uh in this
whatever the components that we have
design before the uh which is coming to
the mixer uh it has a certain offset
voltage and that offset voltage will
also appear at the
mixer this because of this offset
voltage because of this offset voltage
that is uh we o os1 and V OS
this are combination of all the offset
that are present in the
transmitter so this is a
total DC
offset so and this is applied to the
mixer what is the V out now if we write
V out T which is equal to
MT
cos Omega C we we are just interested in
the up conversion that is why we
write V offsite cos Omega CT + 5 plus v
offset cos Omega CT
minus V
offset
C
cos Omega CT so when we multiply this
with cos Omega CT we will get this term
so this is a
desired message signal which is
upconverted at the Omega C frequency
however these are the offset which are
the not desired one so we can find the
relative carrier
leakage so relative carrier leakage
is given by square root of because the
amplitude of this is squared we
offset Square this is if we write one
and two this is one and
two plus v offset 2
squ divide
by m message amplitude
Square so here we can see that this
offset is generating the uh because of
this offset there's a carrier Power
which is leakage and that will look like
this so this is a
message uh message that we want to
transmit and then there is a carrier
leakage so this carrier
leakage if this is a base station and if
you are near to the base station what
will happen that uh your you will your
base station will see the very high
carrier and then base base station send
a signal back to the uh receiver that
you need to uh reduce your power because
your power is high now in reality the
actual power will be there in the
basement which is a low our carrier
Power is high so uh that that b station
is sending another again information to
the receiver to reduce the power
consumption we already seen the uh cell
uh how the cell works in the basic of
wireless communication so if you are
near to the base station your power
requirement is less if you are far to
the base station your uh Power
requirement is high because you need uh
your signal needs to travel for longer
distance so in this case if uh receiver
uh will tell the message to the
transmitter that we need to reduce so
this Bas band processor will reduce the
power however in reality your power is
not actually that much so uh then while
the reception means while the connection
will once connection will happen while
reconstructing the signal there is a
distortion so this is a very important
feature and that we uh that needs to be
carefully uh considered while designing
the transmitter that is a carrier
leakage so what exactly it will do what
what is the kind of distortion it will
add so it will have a two
effects so due to this Distortion the
signal
constellation carrier liage signal
constellation will
change
and another effect
is your carrier Power
dominant dominates compared to Signal
power so we uh while designing the
transmitter
uh we need to be careful of this carrier
leakage and how you can improve the
carrier leakage the uh one of the way
how we can
improve so Improvement on the carrier
leakage will happen if we increase the
so uh message signal power so if we
increase the amplitude of the message
signal that that is uh one way of of uh
improving
so
we
increase the
amplitude
of message
signal so this is one
way but again we need to be careful uh
while uh increasing the amplitude of the
message signal because uh we already
have seen that if you are using a
envelope modulation and then if your uh
amplitude variation is too much you need
a very highly linear power amplifier so
uh that we cannot go beyond certain
level of increasing the message signal
what is another way of uh improving this
uh uh problem of carrier leakage is
reducing the
offset so offset is in our hand which we
can reduce so in order to do that there
are various opset reduction circuits or
op offset reduction mechanism needs to
be added in the transmitter so that this
problem of carrier leakage we can reduce
so this is what about the carrier
leakage
then important is the mixer nonlinearity
so mixer nonlinearity is also important
because uh
here it what it
do it corrupts
a it corrupt the signal or raise the
adjacent power
so
what exactly it will do I will so there
is a problem of the uh adjacent power if
adjacent power will increase then there
is a the we already have seen spectral
regrowth so if this is a
actual desired signal but if your
adjacent power will increase then your
signal will have something like
this
so your signal bandwidth will be
different and your more power will be
there on the existent side so your mixer
should also be a linear and uh we when
we are using a anvelope detector means
envelope modulation at that time uh we
need to be careful that uh the mixer
will not add so much nonlinearity
otherwise your entire basement signal
will uh your entire uh basement signal
will be
distorted so this is about mixer
nonlinearity and uh transmission
transmitter L non transmission linearity
is also important so transmission
transmitter
nonlinearity transmission nonlinearity
is uh depend upon modulation scheme
that we already have seen while
discussing
the B basic of vess
communication like anual of
modulation or another is
a spectral regrowth so if there is a
transmission transmitter has a more
nonlinearity there is a more spectral
regrowth we already have discussed about
spectral regrowth in the LA uh while we
discussing the basic of wireless
communication where uh actually your
signal will be something like this but
due to spectral regrowth the it
will be
something there is a spectral regrowth
will occur and that will distort
your uh actual signal so this is
happening happen because of the
transmission
nonlinearity and this mostly
dominated uh if we see the circuit
parameter that is a
compression so your 1db compression
should be better if we are using a uh
envelope detect envelope kind of
modulation and any uh transmitter that
we are designing mostly the power
amplifier the 1 compression point should
be good so uh and another Point here
that I want to add that is a 1 DB
compression point we have already
seen so this is a uh
actual actual signal will go uh actual
gain will be go like
this but in reality there is a
saturation and due to that there is a 1
DB compression that will H happen so
this P1
DB is a point we should not work at that
that much input that much power input
power so always we uh there is a
standard we'll Define that what is a
maximum uh level uh of the power that
you can uh work and that is given by the
uh back op that is called
a back of
and what exactly mean meaning of back
off uh let's take one example here that
if average
power of 64
quam obdm
signal
must remain so this is defined in the
standard must
remain 8 DB
below of P1
DB what it says that if you know the P1
DB of your power amplifier then you need
to be 8 DB below uh you need to work and
that is called uh so your circuit what
it's called your circuit must
operate 8 DB back off so this is what
back off
means so we should not make our uh
signal to be nonlinear so that when we
apply the uh envelope modulation uh that
will be below the 8 DB and it its
variation should not be that much high
if let's say this is a open signal and
we all also have seen the pick to
average power ratio for the obdm so if
the that Peak Peak power Peak voltage is
too high then we need to be careful that
it is not going Beyond this
backup and uh in order to uh have the uh
sufficient
linearity in order to have a sufficient
linearity we uh the output output swing
of power
amplifier is
maximum
so uh in order to do the maximum uh uh
swing output maximum
swing we should have a uh sufficient
gain in the power amplifier and uh we
need to be ensure that uh the
preamplifiers that pre- drivers that we
are using that should have a sufficient
linearity so this uh graph here what it
says that when we are doing the
transmitter design at that time we also
need to be careful about the swing at
each stage of the amplifiers so at let's
say at the base band you have a swing of
vbb and then after the uh multiplication
and Adder amplifier you have a swing of
VX and then we have a swing of vdr and V
out that is the output swing so all this
swing you need to be carefully consider
and your p pa pre-driver means power
amplifier require that's why power
amplifier require a pre-driver which has
a sufficient linearity added and it has
a sufficient input amplitude which is
given to the uh Power amplifier to get
the maximum voltage swing so for example
the maximum voltage swing will be 20
volt for 1 wat of power
power so this much high voltage swing
you required then your all other
preceding stages should have a
sufficient linearity and it should not
provide that much high input so that
there is a compression will occur so
this entire voltage needs to be
carefully considered while designing the
transmission
transmitter then another problem is a
oscillator pulling so we we are uh let's
say very high voltage is going to come
uh at the power amplifier output and it
swing is too high we have already seen
that is a 20 volt so some of the power
or some of the uh voltage will be uh
feedback means to the oscillator so it
will go back to the oscillator uh and
mixer will not have that much sufficient
isolation so what will happen that you
have a this is a complete base band
which you have upconverted now out of
that some of the portion that is a Delta
Omega if it will feed back to the your
loo then what will happen that this is a
loo input and it is giving it is
observing the Delta Omega input and if
there is a phce change this is a phase
diagram so output phase over the time
diagram is given what will happen that
uh at each uh iteration there is a Delta
Omega change will happen and that will
add a 90° phase shift so this is a 90°
phase shift that is added now this 90°
phase shift after certain point of time
because your Alo also has a positive
feedback and that will also add the more
uh phase change and at one point there
is a 360
rotation H it will try to change the
oscillation frequency and you can see
that at certain point you have a change
in the frequency so this is a uh output
Spectrum if you try to draw the same
thing in output Spectrum so this is a uh
injection Omega injection then you will
have a Omega injection plus base band
that will happen and these are the all
the uh spectrum of uh all the second
third harmonic of basement will be added
and you require your Omega loo should be
set at this frequency but then it will
be injection pull to other frequency
Omega loo plus Delta Omega so this
problem of in oscillator pulling is uh
very severe and it it needs to be
carefully considered while designing the
transmitter so what are the issue
that is causing oscillator pulling uh
that if we
summarize so the one is a internal
voltage and current swing of the Alo so
we need to have a sufficient Alo swing
so that the incoming other Delta Omega
signal will not distort the your
oscillator frequency so uh if they are
less then there is a more effect of
pulling will happen the second important
point is the Q of the tank used in the
oscillator so because oscillator if we
want a better phase noise we use the LC
tank and that should have a better Q if
that Q is not sufficient there's a
possibility that it will M tune to some
other frequency then third is whether
the PA output is a differential in which
case it's pulling to the Loo is 30 40 DB
lower if it is a single-handed and uh
how much is the feedback loop
controlling the L counterparts the
pulling so if we have a too many
feedbacks or in the PLL or synthesizer
and that not needs to be uh reduce then
this pulling because if there are more
feedback there's a possibility of the
injection pull is high and the symmetry
of the layout and type of packaging so
this because if your packaging is better
the if you are using op power amplifier
also then there is a in uh Power leakage
will not be that much high and if your
layout is symmetric then the phase
difference will not be that much uh high
that will reduce the problem of the
injection pulling so this is uh how we
can uh reduce the injection pulling
there is another me mechanism also we
can do that is uh called a modern direct
conversion transmitter in which we use a
divider so in between there is a divider
can be used which will uh isolate the
loo and uh mixer or the at the input of
the mixer so that it will not see the
sufficient fed through so there are two
ways yes one is you can improve the
isolation in mixer so isolation between
Port
so improve the isolation between port or
you add the
divider or
buffer so there are some uh buffer
requirement is also there which will
differentiate the loo and uh mixer and
the this will reduce injection pooling
greatly and the divider readily provides
quadrature phas so another Advantage is
uh using divider is the phase we can
easily
generate however disadvantage of this
circuit is you need a twice of the
Alo let's say if you required 8 GHz or 4
GHz then your requirement will be 16 or
8 gig so your allo frequency is
increased then your power consumption is
will also increase so we need to uh also
uh suffer from the higher power
consumption when we go for this
architecture however we can get rid of
the problem of injection
pulling then there is a uh so these are
the all Dem merits of the direct
conversion transmitter we already have
seen derates of direct conversion
receiver so whatever we have discussed
like uh IQ mismatch or Carrier leakage
or mixer nonlinearity transmitter
nonlinearity power amplifier
nonlinearity so this are the problem
caused in the and injection polling that
is a direct conversion transmitters the
way we have done a
Hine receiver similarly we can also make
Hine transmitter so same thing here you
need a two L this is a COS Omega Lo and
here it is a sin Omega
L sin Omega L2 T and then another cos
Omega 2 T which is uh up converted which
will so this you can at the base B you
have conver to certain frequency and
Omega 2 that is a at higher frequency
and here you will get this is a Omega 1
then your output you will get Omega 1
plus Omega 2
so this can also be considered as
a here there is
a COS Omega
1 cos sin Omega 1 then this Omega GA 1
uh will be up converted to Omega 1 +
Omega 2 and there is a carrier Power so
this uh now this is a carrier that is
carer liage problem can be solved
because the if we use a
base
uh band pass filter here then that band
pass filter will filter out the Omega 2
component and only Omega 1 plus Omega 2
will be a trans
so uh there is also same problem of
carrier leakage will be there like uh uh
we have seen in direct conversion and
the more uh severe problem is a mixing
Spurs because we are mixing a two times
there are n Omega n Omega 1 plus or
minus M Omega 2 plus or minus M Omega
Bas bent so this many and where n is
equal to m is equal to n
m l is equal to l which is 1 to n so
there are many mixing Spurs will happen
and that will distort the Bas band uh
this Bas band transmitted signal so that
is the Dem merits of Hine
transmitter then one of the transceivers
transceiver architecture transmitter
mostly it is a combination of
transmitter and receiver where uh onop
keying also widely used so uh why uh uh
we are discussing here on op Kang
because uh there are many application
like iot where we don't required very
complex modulation and we are more
concerned about the power consumption
our data rate will be less so we here uh
we can use a simple modulation scheme
that is called onof keying so there are
two ways we can implement the onof
keying one we can switch the Alo uh
hello frequency by changing the
amplitude 1 to 0 1 to0 so the carrier
will be transmitted and uh when there is
a no uh when there is a zero the carrier
will not be transmitted so this is same
like amplitude shift
key and then there's a power amplifier
and it will amplify the signal another
also you can give a continuous allo and
you can switch on pa uh on and off that
can also be done so uh this is a very
simple uh uh transmitter architecture to
implement and in many uh uh many case we
can use then there is a receiver that is
a uh envelope uh receiver uh you just
use the envelope detector and low noise
amplifier you can detect the uh what
whatever transmitted signal that you
have sent so this is a simplest
architecture it is a low cost low power
it can be used for low cost low power
application so uh this is what about all
uh we have discussed about the uh RF
transmitter and receiver
architecture uh now if we see that what
are the basic important component that
we have used uh in uh the transmitter
and our architecture that let's say we
can not it down we have
use
LNA then we have also use
mixer then PL or
synthetizer or
oscillators or there is uh one more
component that is uh uh
filter then ADC dac's
we cannot avoid antenna
also and power
amplifier and if
have
amplifier so these are the basic
components that we have tried to study
tried to see that these are the
components required in order to design a
uh good re transmitter or good receiver
so uh as far as this coures is concern
we will try to analyze LNA mixer pla
oscillators even a power amplifier you
can go for the separate course on
antenna design there is a mix signal
course you can separately go for mix
signal course on this where filter and
ADC both will be covered even microwave
filters you can go for the microwave
course and uh the iip amplifier you can
uh use the advanc analog circuit course
so so uh we'll try to uh study all these
uh components in the uh upcoming uh
lectures but before going for all these
component we required a uh understanding
of Active Components which are used in
RF and passive because without that we
cannot construct the RF circuits so this
is how uh then upcoming course will be
there then we will discuss about active
component passive and then we will move
to the amplifiers design so uh thank you
uh we will discuss about Active
Components in the next
[Music]
class
[Music]
a
