1 Video View·Jan 11, 2024 #sawblades #sawblade #tablesaw Table saw blades need to be handled and stored safely. Laying them flat against each other isn’t good either. When it comes time to get them sharpened, you need to carry them safely. This holder-carrier “checks all the boxes!”
#sawblades #sawblade #tablesaw #mitersaw #trimsaw
Buy your DFJ T-shirt, Cap, or Coffee Mug at https://www.dirtfarmerjay.com/shop
Table saw blades are hard workers and deserve to be treated with respect - both in use and when stored. Some makers have created dedicated organized storage spaces to keep the blades safe, organized, and labeled - ready to access, use, and put back when the job is finished. That’s the approach we’ve taken around here.
But, what if space is limited? And, just because you have a great blade storage drawer or rack doesn’t mean you have a great way to transport your blades when they need to be taken to a sharpening service or jobsite.
This handy shop-built combination addresses storage of about six blades, as well as transport out of the shop.
You’ll need a piece of ½” (12mm) baltic birch plywood, a gate or swiveling handle (to be mounted on top of the carrier), ½” (12mm) long mounting screws for the handle, glue, a short section of ⅝” - 11 threaded rod. This is the most common size arbor hole for 10” blades. In Europe and other areas, other sizes may “rule.” If that’s the case, then you’ll need to modify this build by getting threaded rod, jam nuts, washers, and wing nuts that fit the arbor of your saw blades.
The main plate dimensions of the holder are determined by the size of the blades you will be stowing. We made the plate about 1-½” wider and 2” taller than the saw blade. We then made the top and bottom the same length as the main plate is wide. The top and bottom are about 4” wide.
Before grooving the top and bottom plate, we drilled a ⅝” hole in the middle of the plate. We then glued everything together, gave it a touch sanding, and applied a spray polyurethane finish. Once dried, we applied the 4 rubber feet, and centered a 4” section of ⅝” threaded rod in the hole and secured it with a jam nut from each side.
Saw blades can now be added, with washers placed between each blade. This ensures that the blade teeth don’t touch each other. Three blades fit on each side and are secured with a large wingnut. Easy and effective!
⅝” fasteners may not be readily available at your local hardware store. They weren’t at mine. So, we ordered them from one of our favorite fastener and hardware suppliers:
www.boltdepot.com
Here’s what we ordered (including spares for future projects!):
6 - #7684 Wing nuts, Zinc plated steel, 5/8"-11, $2.63 each
6 - #2665 Hex jam nuts, Zinc plated steel, 5/8"-11, $0.21 each
20 - #4273 SAE flat washers, Zinc plated steel, 5/8", $0.17 each
The order totaled just about $30, including shipping and tax.
I may build more of these and use them as combo organizers for blade drawers as well as for transport.
Do you have a blade storage solution you’d like to share? We hope so!
JUST DO IT YOURSELF!
Instagram: https://www.instagram.com/dirtfarmerj
Facebook: https://www.facebook.com/dirtfarmerjay
[Music]
hey dir farmer J here from dir farmer
j.com let me show you how I built this
handy blade carrier that keeps them safe
and secure and lets me know which ones
need to be sharpened and which ones are
ready to go to work hey stick
around hey dir farmer J here from dir
farmer j.com a little while ago I built
this little IE beam shaped uh saw blade
carrier uh that makes it really easy for
me to know which blades are Shar sharpen
ready to go which ones need to be
sharpened and when I take them to the
sharpening service it gives me a great
way to transport and uh to keep them
safe now it does take a little bit of uh
little bit of U special Hardware I'll
show you that in just a second I'm not
going to give you plan by or uh detailed
plans here but the overall dimensions
here are about 11 by 14 in tall uh in
centime that would be 28 CM roughly by
36 in or 36 cm
uh and so uh and this is roughly uh 3
and 1/2 4 in something like that right
in this width here we put a heavy duty
handle on the top to to carry it or at
least to get it off the table to pick it
up it's surprisingly heavy uh when you
start adding blades to it uh but now
things are secure and even if this falls
on the side the blades are going to be
kept secure and it uh is a really great
way to Stow the blades in the shop here
now it does take a little bit of of um
specialty Hardware because uh these type
of wing nuts what I have in here because
the Arbor on us blades the hole in the
middle of the blade is 5/8 in I used a
short section A 5/8 in Rod I bought from
the metal supplies store or you can get
it at your big box store and get a short
length of it cut it to length burnished
the ends ran the nuts up and down it so
it was smooth and then what I did is I
put the uh short Rod halfway through let
me show you that all right you can see
the short section of Rod right here
centered pretty much right right in the
middle of this middle web and we didn't
want them real long out here two reasons
one I don't want that exceeding being
far out past the protective edges of
this the top and bottom uh structure
here but also um you get that many Saw
Blades this just gets unwieldy so this
is uh essentially for about three
different saw blades on each side now if
I use standard thickness nuts right here
uh that would use up a significant
amount of the thread on here so what
these are called are jam nuts I got
these jam nuts right here from Bolt
Depot and you can just go up to bolt
depot.com and these are 5/8 11 in or 11
threads per inch with a wrench size of
15/16 uh and so these nuts are much
narrower and therefore we were able to
put them on both sides counter tighten
them and now that gives a post out on
each end then we go ahead and start
applying our saw blades onto each
side and as we do so just to make sure
that as we stack the next one on I also
have used uh these washers that I got
from Bolt Depot I can use the bigger
ones or the smaller ones and they simply
act as spacers to stop the teeth from
colliding when you're transporting
[Music]
blades now the next special uh piece of
Hardware you'll need are these large
wing nuts which you're not going to find
at your typical big box or hardware
store bolt Depot has them these are 58
by 11 also uh large wing nuts and so
they simply go on
here and tighten down beautifully and
now you have a great way to transport
around your
blades inexpensive effective and keeps
them safe well there's a technique that
you can build your own saw blade carrier
keep those blades safe and keep them
also the edges away from you so you and
other people work in the shop are less
likely to get cut do you know another
thing that is sometimes a real hassle or
just a challenge in the shop is building
drawer boxes and it can take a lot of
steps or just a few we'll check out this
video that we produced called the
quarter quarter method where you use one
saw setup to cut all the joints you need
to build all the drawer boxes you need
and while you're at it check out this
other video that we produced that
YouTube thinks is perfect for your
interest until the next time this is
dirt farmer J from dirt farmer J .