This nifty saw, reasonably priced, makes it pleasant and easier to JUST DO IT YOURSELF! We recently added the DeWALT DCS361B 20V Max Cordless 7-1/4" Sliding Compound Miter Saw to our toolset.
We already have a very nice 10” Makita corded sliding compound miter saw, so why did we add this? It may have something to do with DirtFarmer Jay being a tool addict, but there is a better rationale for purchasing this saw than that.
Our bigger saw is part of the essential tooling in our main shop. It’s mounted on a saw cabinet and it’s a hassle to break it down and load in the truck for any remote job. It’s heavy too! And, most of those remote jobs are small, needing only moderate-sized cuts and not a lot of them at that.
That’s where this saw comes in. It’s part of the DeWalt 20V Max and XR cordless tool system, so all the 20v batteries and chargers we have work just fine to support this saw. I use either a 4 or 5 Ah battery and I can run just about all day on that one pack. Even so, I carry a pack or two extra, along with a charger.
The saw is compact and pretty easy to transport. It stows nicely in a locked 45-degree position, along with the saw in the down position, and the slide locked. There are nice built-in carrying and hanging handles in the saw platform. The angle markings, detents, and lock handle all present themselves nicely and are easy to use. The saw is lowered into the work using a “D” handle that is comfortable and allows you to use the saw without rotating your wrist. The bevel lock and gauge are easy to use and see as well (for those of you that like to flat-cut crown molding!). The battery pack port is readily accessible and the battery locks in securely but disengages smoothly.
There is a light that illuminates the cut line pretty well, and that comes in handy when the worksite starts to get dim at the end of the workday. The included dust collection bag fits a 1-¾” (44.5 mm) port and works just about as well as any of these kinds of saws (not that well, unless connected to a vac).
Our saw was made in Mexico, at one of the DeWALT facilities there. The fit and finish are very nice, and it came with a Freud 7-¼” 60-tooth narrow kerf ultra-fine cutting blade, a contrast to some other tools that come with the cheapest blade available. You also get a blade wrench (which stows nicely onboard the saw) and a material clamp.
As for cutting capacity, you can cut 8” at 90 degrees, and 5-½” at 45 degrees. Thickness is up to 3-½”. For a complete listing of cutting capacities at various bevels, miters, edge, and flat cuts, visit https://bit.ly/DFJDeWaltDCS361BSpecs.
While we wouldn’t use this saw to cut studs or in a high-production setting, it does great with trim and short-burst jobs. If you do side-jobs, handyman work, or do warranty work on finish items, this is a tool to seriously consider. Getting it packed, transported, set up, and taken down at the end of the day is all easier because of it’s small footprint and low weight.
We purchased our saw and there is no promotional benefit to us should you decide to purchase this tool. It’s our pleasure and part of our mission to find good tools and pass them on. And remember, use of these types of cutting tools carries inherent risk which you assume. Read the manual and safety advisories and work safely, including good lighting, safety glasses, and no being fatigued. Tools have no brain of their own, so you have to use yours! Be safe so you can enjoy your craft ongoing. The small size of the saw may tempt you to not to give this unit the safety respect it deserves. It is powered well, and the blade is very sharp.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. Hey, I've added another tool, my set of cordless
tools from DeWalt. This time it is the battery-operated seven and a quarter inch sliding
compound miter saw. Well, what do I think about it? Walk through this with me, I'll show you some
of the features of it, our initial experiences with it, what we like about it, and maybe a
couple things that they could have done differently. Stay tuned. Hey, Dirt Farmer Jay from
DirtFarmerJay.com. Thanks for joining me today as we review the DeWalt DCS-361B seven and a
quarter inch portable miter sliding saw. Or is it sliding miter saw? It's up to you. In all fairness
though, DeWalt calls it a sliding compound miter saw, and that's pretty descriptive. Now, why in
the world would I get one of these tools when I already have a powered one? I have a nice Makita
10-inch that is the same type of thing as sliding compound miter saw. Why would I do this? Well,
there's a couple good reasons. One is this is great for little quick cuts, for good trim type
of cuts, but it's also very portable. Let me walk you through a couple things here. In its stow
position, you would simply put this pin here, which stops the arm from coming up. You can slide this
back or forwards, and then lock it into place just using that thumb wheel right there. So now
it no longer slides. And if you want to condense its profile even a little bit more, you can swivel
it to the side, lock it in place, and now it is ready to transport. There's a couple great things
about transporting this. Number one, integrated into the table itself is a couple of handholds
right here. And you can actually pick it up on one end and carry it that way if you like.
And there is also a nice top handle, so it works very nicely as far as stowing and getting ready
to go. Now when it's time to use it again, you would obviously pop in a battery right here.
I use either a 5-amp hour or 4-amp hour, although I've put in one of the smaller batteries and run
it for a period of time, it's fine. But getting ready to work, we're going to go ahead and pull
that up, let this come up, undo the slide here, and now you can push in the detent right here and
bring it around and get ready to go to work. So it has nice detents already preset, which allow you
to very quickly hit zero. Here's one at 10, here's one at 22 and a half degrees, which is of course
half of 45. There's a 31 and a 0.6 and a 45. All are there ready to roll. So it's very nice,
it clicks in very nicely. One of the things you got to have in a tool like this is infield
adjustability. If the saw gets whacked, gets dropped, just in everyday use and it loses its accuracy,
then the main benefit of having the saw is greatly diminished, of having very accurate first time
cuts. So there's a couple things here. First of all, on the angle side to side, you have the
adjustability right here. So you could adjust this indicator once you had a true 90 set up and you
knew it was correct, or you could do a 45 degree test cut and make sure it's landing correctly
where you want it. So that allows you to make sure the indicator is dead on and is telling you
the truth. Now back here on the compound side of being able to adjust the saw this way, here we're
set, if you look down the indicator, we're set at zero degrees here. By spinning the back hold,
I can now rotate the saw over and I can put it in any place I want. But notice when I bring it there,
it settles in at 45 degrees. Well those two, 90 degree and 45, obviously are used quite a bit and
they have to be accurate. And the way DeWalt accomplished this and made it really easy
for you to maintain accuracy and to adjust again if you need to, is right here. These bolts,
one on each side, and this plate that land on it. So when I bring this back over,
untightening this, rotating over and having it land on the top of the bolt head,
now you'll see that the indicator reads zero. And if I rotate it the other side and have this come
down onto this bolt, it's going to read 45. Well once you do test cuts and you make sure it's
absolutely beautiful, you can adjust that up or down and keep it maintained in the field or on
ongoing use. An important feature, something that needs to be simple, intuitive, and very accessible.
Now let's talk a little bit about the blade itself. The blade is a seven and a quarter inch blade
and lots of teeth on that. I believe that's an 80 or a 60, I don't recall, but maybe we'll see it
right here on the side. There it is, a 62. So that's a 60 tooth blade, thin kerf. Thin kerf is
important on a battery powered tool simply because of less cutting resistance, longer battery life.
This is a finish saw, I wouldn't use it for framing. Cutting two by fours, although a nice
two by four from time to time you may, but it works really well with trim hardwood. It works
fine and I'll cut some of that in just a moment. I'm going to pull the battery on this so that
there's no chance at all of this firing up. So a couple things on this. One, the handle is very
nice. This is a D handle and notice the way it's set up. Your hand naturally lays on the top.
The safety's right here. You simply pull that little trigger back and then notice it's a two
finger trigger, which greatly reduces fatigue. And when you're doing a lot of trim work,
little things like that matter a lot. There's also a light here that you can push on to get
light here. We'll show that in just a moment. And so this D handle is very nice and lays nicely.
As far as changing the blade, there's a, I would go ahead and lock this in using the slide,
so it's not running forward and backwards. You're going to push that in and when you do lift this
back, you'll notice when I push that in, that locks the blade and we'll find it, the detent.
Here it comes right there. Dropped in, now that blade can't rotate. And notice if you come around
the backside of the saw, right on board is the change out tool for the blade. So they really
thought that out, that rides along with you. And if you come around on this side, you can see
that that matches that six-sided indent right there. This part right here allows you to remove
the blade guard back to get the blade in and out. And of course, you always need to install the
blade in such a way that it is cutting against the fence. Sometimes some people will get that
reversed and it's not so pretty when that happens. So this is the correct cutting orientation and
there, that is very intuitive. Great manual that comes with it as well, so you can look through it
and it tells you very quickly the operation setup and some of the safety features. Something I want
to mention really quickly here. Go ahead and safety up a bit. We've got our glasses, we're going to
go ahead and throw in the battery. Battery just clicks in very nicely through the detent. There
we go, boom, it's in. And you can see once I feather the trigger, runs very nicely. You've got a nice
little path of movement right here. So that works very nicely. Here's, you can see the light that
has come on as well. So there's your light. And so that is extremely handy. I was on a small job at
my friends Bill and Sylvia's place and we ran out of daylight. And so we had about a half an hour
of darkness where I was doing some final little moldings on some stair balusters. That light
allowed us to finish up and do it beautifully. So this is great. And if it's a little bit dim in your
shop, makes a big deal as far as looking at fine points. Because when you're doing fine cuts, you
want to be dead on. Another thing that is very important to keep in mind is where your hands go
on this. Obviously getting close to the blade is a no-no. So notice right here that there's these two
intuitive lines and the sign saying don't get your hands in closer here. Keep your hands
out from it. There's different hold downs and that sort of thing to assist you in making sure that
happens. The back fence right here if you notice has holes in it right across here. So you could
put a sacrificial fence on this which can range everything from quarter inch MDF to a piece of
plywood. Notice though whatever depth you add or thickness you add to the fence you lose in cutting
width here. Okay so keeping the hands out of there. Well let's see how it works. I'm going to take
this is a piece of soft maple. Let's just see what it does and how nice a cut it leaves. So
there it is beforehand. Rough cut from the lumber supplier. Let's run it through the
blade. Let's just see what it does. So obviously we're going to place her here. Here we go.
Very nice. A little bit of chip out on the back which is to be expected.
As you can see nothing that's not manageable. Does a nice job. You can hear the saw didn't
bog down a whole lot cutting through that. Did nicely. Let's throw a piece of cherry in here.
Here we go again. This is a little bit dry and bent around a bit. We'll go ahead and put this
over here. Let's just see what we get. Again thin kerf. Looks great. Let's pull that off. As you can
see that 60 tooth blade does a wonderful job. We have a little bit of a rub right there but that
is really smooth. So it does a nice job. All right those are bigger pieces of wood. How about something
like this? We've got some trim and you need to cut this. Well let's do a 45 on that. We're going to
go ahead and rotate around to 45. We'll put her here. Here we go. Lower the blade down. Very nice.
Very clean. Does a great job. The blade did not kick back or throw the cut off any significant
distance. And so this support system works pretty well. Now this taper back has to exist so that
when you tilt over the saw the blade doesn't end up colliding with the back fence. Well let's cut
this little piece of molding. Let's just see. It's been cut once before on another project I'm doing.
I'm going to go ahead and pinch this down. Here we go. Pretty pretty. So very nice. Very clean.
Plenty of power to do this. I just keep one of the batteries in the charger on going. It works just
fine. Let's talk about cutting capacities. I know that's something that's important for you in this
saw. So when the saw is set up just in flat vertical this way where it's not tilted it'll cut
up to three and a half inches thick. At 45 degrees it'll cut something five and a half inches wide
and if it was set at 90 out it'll cut up to eight inches wide. So it has a pretty doggone good
capacity for a compact saw like this. If you want to know about all the other cutting capacities
which include various angles, bevels, different settings, compound settings, check out the link
that I've got in the description below that'll take you right to the DeWalt website that has a
whole chart of all the different settings and widths and capacities. That'll be very helpful
for you if that's a consideration when you're going to purchase or not one of these saws. Well
if you have something like this that you would like to share with your fellow viewers or you
have some further insights on this type of saw or this very model feel free to share that in the
comments and we'll make sure that everybody else gets to see it. Well if you found this to be
helpful like the video and better yet subscribe to our channel and when you do make sure to ring
the bell so you'll be notified immediately when a new episode comes out approximately every Friday
on the home, the garden, truck, shop and just hands-on living. Until the next time this is
Dirt Farmer Jay from DirtFarmerJay.com