I waited until this drop tower's systems were all worked out to show any of it but here it is. I think it gives a lot more context to what it takes to do a drop test and the variables that happen. I prefer to keep break test videos edited tight so I usually skip over all of this process during drop tests. Do you like seeing the systems I use for testing?
We're going to drop test a Dyneema and nylon sling that are 20 years old today.
Safety first.
I'm going to show you how I set up my new drop tower here on this tree.
Now, this might make some people upset that I'm doing this on a tree, but I did
do a ton of research on standards used in ropes courses, tree housers, is that a
verb, tree house building, talk to some arborists.
No trees are being harmed in the making of this video.
Also, this is on a private property and more convenient to get to than the
drop tower I had in Loda, California.
Which I still have access to, but this is a shockingly useful and a lot more
convenient for me to get to when we just want to do a few tests, which is usually
all we need to do to supplement a video.
I don't know how many people are trying to drop test things, but I sure wish I
seen a video like this when I was trying to figure this out.
Even if you're not trying to drop test things, the process might
be very interesting to you.
What's neat about this tree is it's leaning a little bit because you don't
want where you're lifting the dummy.
You don't want that to be right above the load cell.
What's interesting is you can't have a, like you can have a perfect ish factor
one fall, Ooh, that gets in the weeds real fast.
Let's not do that.
Believe it or not.
The plans I drew up for all of this was super complicated.
And then after using it for months now, it, uh, just this simpler is better.
And what's great is the line scale three, after doing some tests was fast enough
to test and capture the peak force of almost anything we're dropping, even
this really static stuff, because it's 1,280 Hertz.
Now, how do you attach this to the tree?
Glad you asked.
Uh, I'll show you how I do that in a minute.
Let's start with how the tree works.
The tree doesn't Rick doesn't wobble.
It's actually a really big tree and we're only this far up of it out of a tree,
this big, so it's kind of nice, uh, that it's super strong enough.
This isn't something you probably want to do on a skinny tree because
then it would flex a little tiny flex.
Let's say in a beam square tubing or a tree, like the little, little,
tiny flex isn't probably going to throw your samples off that much or your
results of your tests, if you're testing things that stretch anyways.
Uh, some people were worried about the flex in the square tubing I had
on the drop tower in Lodi.
Um, but I didn't find that to be a problem.
It just wasn't moving enough compared to the variables that happen
when you just drop a heavy weight.
Back to the tree.
Our tree here is leaning probably easier to see that angle this way.
If I put the line scale here, where we're lifting up the pulley that's up here,
probably 15 feet higher is, uh, hanging out a little further.
So then the dummy comes up here and then when we release it,
it passes right in front of it.
You can't have this directly underneath or it would just crash right into it.
And so every fall ends up having just the tiniest little swing, which that's what
you're trying to eliminate when you're doing a drop test is having it swing
around too much because that could, that could throw your numbers off.
Hopefully this is a 30 second explanations of fall factors.
If you fall one metric foot and you have one metric foot of rope out,
that is a fall factor one.
If you go up higher and let's say you are straight up and you fall two feet down
on one foot of rope, that's going to generate more force because there's
less rope absorbing your fall.
Hypothetically, there's a very static rope that wouldn't catch anything, but go with it.
If you are 50% higher and you fall one and a half feet on one foot of rope,
that is a 1.5 factor fall.
Now, a lot of the standardized testing is 1.7 or 1.8 fall factor because it's just
really hard to have a two and drop straight down.
So it's got like a little bit above belly, it's up here and then it drops.
And oftentimes we're able to accomplish that on this one.
Now, as long as I keep the tests internally consistent, I kind of do
whatever I want, depending on what we're trying to accomplish.
We'll get into that later.
So as they say, show, don't tell.
Let's take the nylon and Dyneema sling and show you the process of what it takes
to set this up, to do just these two tests.
And God knows it's probably going to be a long video.
Before I can go up in the tree to release the dummy and film it, we've
got to lift the dummy up there.
So let's prep the dummy and get it about yay high off the ground to make sure we
like the way it's all set up.
In the nature of being an all natural drop power, we use some firewood and some
bark to make a soft landing.
I didn't want to use rubber out here because that would obviously not be as
good.
If our store is very successful and we have to move to a larger warehouse, I'm
going to find one that I can have an indoor drop tower because there is so much
sap on this quick release that it's just not ideal.
I don't know if that's sap or bird poop on our dummy.
So this is a quick release and this is what you see me jerk pulling in all the
videos and we took one of the 12 strands and 12 braid Dyneema and pinch it off in
there with some weird overhand.
And so when I pull down, goes up and over and opens this up when there's weight on
it and you pull this, it lifts that up, opens it and drops the dummy.
But that's the only thing holding this when we lift it.
And once we have this thing above our heads, no one gets underneath of it.
To keep things simple, this dummy is 15, 10 pound weights with about one inch all
thread going all the way through in this eye threaded on there.
And that's worked pretty good.
And people are like, Oh, a steel dummy isn't exactly like a human body because it's
not as squishy.
Yeah, but you know how much those dummies cost?
More than this drop tower.
Now, once I put the sample on here, I want the pull cord to be on a certain place.
So I have a swivel in here.
It's, I think very important to be able to turn this around the way I want.
Now, this isn't what I used to connect.
This is what I have as a weight.
Once I release this, the rope won't come back down if there's no weight on it.
So that's just the way the end of the rope is here.
That goes through the swivel.
And now we're going to lift this up and make sure that's not cross loaded and that
this doesn't get stuck on anything.
So it doesn't release on us.
How do we lift this up?
You ask?
Well, that's the thing I'm the most excited to show you today because we got these
winches that solve a lot of problems for us, not just here, but when we want to pull
our five to one or sometimes nine to one, you can break test things out in the wild.
They're better than capstans.
We'll get into that in a second because this rope has to go up through a pulley
that's about 15 feet higher than the master point where things are going to be
dropping.
Now, in this case, I had to pick that height for two reasons.
One is how far over the tree was leaning.
So that is the height I have to be at in order to keep it away from my line scale.
So it doesn't hit the line scale.
So if I, if the pulley is here, it'll lift up the dummy here and drop it in front of
the line scale instead of hitting it, which I've broken enough of these, if you've
seen the channel long enough.
So I've actually not damaged this at all on this drop tower, which is great.
The other thing you have to consider on the height is by the time you add this and
this and the pulley and all this stuff, all of this, you lose two meters, maybe by
the time from the highest point.
And that's assuming the pulley is the highest point.
Oftentimes you're putting a span set around something, or in this case to be
girth hitched to span set around the tree.
But the drop tower in Lodi ended up having to be like 45 feet in order to get our
samples 15 feet above the master point.
So it's, it's crazy how high things have to be in order to just drop something 10
feet before you allow for stretch the dummies height, the line skills, whatever.
So something I'm learning is to not leave the stuff outside.
So it doesn't get all gunky.
So I bring my micro traction here and I put it in.
This is by the way, is a nine millimeter polyester rope.
So it's very static, polyester, polyester.
And pull that through.
And I'm going to clip this to here.
What's nice about having it on a swivel is it needs to be facing a very specific
way because pulleys are strong.
If you're not pulling the plates apart, what broke?
So our protraction here, um, no longer goes back together.
This plate you can see is kind of bent that way.
And this one is bent out.
Now this hanger is in this tree with a three eights lag bolt about yay long.
So super bomber enough.
Now we did try when we first started this to, uh, just pull it up by hand, but we
got a new, better way.
So I have this sling around this small tree because it's only got to lift up 150
pounds plus a little pulley friction.
And what I started with originally is this capstan.
There's pros and cons of capstans.
This thing is super, super loud.
It's heavy.
That's obnoxious.
It technically works.
The problem is when I want to release the pressure and put it all on the micro
protraction, so I can take this out of the system.
So it doesn't fall, which is massive improvement from what we did in Lodi.
We had a lawn chair under this thing and it would crash into it.
We've come a long ways.
I'll start with this device.
And then I'll show you the pros and cons of this versus the other thing.
So this drum, you just wrap, uh, three, four or five times, depending on the
diameter of your rope and this case we'll do five.
And then I can pull this up, which we'll get started here.
So that is a little weird the way this hangs here because it's big and heavy.
And, and then I think this is the biggest issue I have with it.
When I want to release it, it wants to bunch up on itself.
It doesn't lower well, but that case it did.
So just take my word for it.
Now I removed that out of the system because the micro attractions
actually holding it up.
So this is where I do my final checking.
I make sure that this is where I want it.
And I fluff up the bark.
Uh, this isn't cross-loaded.
I like the way this is.
I check it.
It looks good.
Boom.
Now I'm not going to come over here.
Once this is above my head, think about it, but we can lift this up and we can drop it.
Cool.
What are you going to test?
Right?
This is an industrial sling or a span set, and you can see that I electric
taped this in place, just kind of like a dog bone on a quick draw.
Keeps this from rotating too much.
Um, the problem is you don't want to put something like this on here and then it
gets up and then cross loads or sits like this, and then it just, I've broken so
many steel carabiners in the drop tower because that problem right there.
So I crisscross zip ties to hold it in place.
Now, if we're trying to break test a carabiner, you have to
use something super static.
Well, why don't we use this?
This is super static.
Yeah, but it breaks at 14 kilonewtons because it's so static.
It doesn't like the knots well, even though in some big drums, you could
probably get 20 kilonewtons out of it.
Anyways, you can't just use rope to break test things.
That's good news, right?
So some people are wondering why we're using these weird things like this.
It's because it's strong enough.
Now we're not testing carabiners in this case, we're testing slings.
Now, if I just want the easiest breakfast I can do, I would dirt hitch this in here
and then I would clip it to the line scale and that would be super easy.
I wonder if we should actually do that.
The other option is I take this steel carabiner and I clip it here and then I
electric tape it here and zip tie it there.
Let's do that.
You crisscross the zip tie.
It'll keep your carabiner from not getting crisscrossed because you
need it to fall on the spine.
Now you know why we don't show you the whole process in every video.
Think how boring that would be.
So on this side, I'm going to be clipping this to the line scale and I'll show you
how I do that up there, but I also don't want this to rotate, so I'm prepping it
down here.
That way my sample's completely done.
If I'm by myself doing this, I would pretty much pull it up to the height that I
want it and hopefully I can still reach it when I'm working up there and how I
know if it's the right height is you don't want this point to be to where you
can't clip it to the line scale anymore.
So you're kind of guessing, but if I have help down here, they can kind of micro
adjust it, which leads me to the Z2.
This is the Z2 and they also have a Z2R.
We sell these in our store now because I liked them so much.
They're designed for an 11 millimeter rope, but I found this nine millimeter
rope works just fine.
Any oval is going to work great, or in this case, an HMS carabiner.
And so as long as it sits well here, what's nice about this is I can pull it
tight and then I just put a drill in here and that's what's going to crank it up.
The guy who translated the Bolting Bible into Chinese told me about this and got me
one and I liked it so much.
I asked him if we could sell in a store and now we are.
You do not want to use an impact drill.
Ask me how I know, but you do need a good, powerful one.
I don't even have to feed the tail.
It feeds itself.
Even on the Ronin, you need to have a second attachment point like
an ASAP and an absorber.
So this is just to assist getting you up a rope.
What's nice is when you're done getting yourself up to a point or lifting up what
you're trying to lift or hoist out, whatever you're trying to do, you can
take this off and attach it to yourself or put it down and just operating
this is going to be a lot easier.
So let's say I have this all the way up and where I want it and I want
to release the pressure on this.
It has gears in here, which you can see on the product page.
We have put a lot of effort into the product page to make sure you understand
this device before you ever get it.
And so you go down and up and you could crack the gears here and then you
could lower this thing and you can descend with it.
Now, if you're using this for rope access, you would want to always
have that second attachment point.
But as long as this is open, the pulley is free to spend.
Now it also progress captures when it's not open.
I am curious about your feedback because if you don't have a large
team to haul people in a rescue situation, I wonder if this
would be worth hiking in.
I don't know, but, but as far as the drop tower is concerned, the
micro attractions doing all the holding.
And then I just removed this and I'm going to put this at the height I want.
And then I'm going to climb up the tree.
Don't want it higher than that.
It's kind of hard to like clip thing.
The line skill wants to come out and then it smacks things.
But anyways, up, down and release, release.
I didn't do this entirely.
Make sure I don't drop the dummy on this rope.
Do not stand there while there's something above my head.
I'm thinking about getting a full face shield after an incident.
Last time I was on here for science, where shrapnel came off of a crossloaded
carabiner and made me bleed.
And if that was not on my arm, but maybe on my neck, I don't know.
It's kind of hard not to stand there and operate things.
Now I'm going to prep the line scale.
I want to have the shortest soft shackle that I can put on here in order to
orientate this thing to be face out.
Cause obviously I don't want it to be against the tree like this.
And so in order to put it on here like this, then I have a second one that's
going to actually go around the all thread that goes all the way through the tree.
And that is almost a one inch rod.
It's I think seven eights inside of a one inch hole.
And then I just have a little pipe that goes over that.
So I'm not putting this directly on the threads and this is just going to sit on
that thing, but you can see from my high point where it's catching everything to
my low point, which isn't technically even this, even the big ones, if you were
to put the 10,000 Hertz load cell up there, it's got a cable coming out, going
to a laptop that needs power.
It's frustrating.
But, uh, even if you do that, you have this giant shackle that goes through the
eye.
You can't clip too many things that you can't just clip a carabiner to that.
It's too fat.
And so look at the height distance you now start to lose.
When I start to clip this carabiner up there and then it's going to drop this
soft shackle chain for the line scale.
Three has been a good setup for this tree.
Now I'm just going to clip that off to myself and I have my personal anchor, so
I can be clipped in at all times.
The tree is a little sappy.
That's why I wear these.
Let's go over there.
Now I have a perfect descent installed on a very bomber anchor up there.
And that is what allows me to safely go up and down this tree.
And then I put in these climbing holds.
I thought that was fun.
So now that I've double checked, I'm connected to these things.
The biggest risk on this is forgetting to use it.
It happens.
I'm going to go up there and then I'm going to kind of show you the process up
there.
So I have a nut on there and another nut and then I just put the soft shackle right
on there and it hugs it and that goes all the way through the tree there.
I also am tied into here and here with bolts that are quite long and are 3
eighths.
So I have an in-depth video you can find on our Line Scale 3 product page that
goes into all the settings you'd want.
In this case, I'm not going to log anything.
It is at 1280 Hertz and peak mode.
I squeeze it and you can see that it's holding the peak force.
And so I can make sure that we're all set to zero.
You might say that this absorbs some of the fall, but these soft shackles, other
than settling a little, are not absorbing anything.
There is settling in here and they're settling in this adjusting.
They're settling everywhere in a drop test, unless you have a very fancy
machine.
So now you can see this is orientated right when I jerk pull it like this and
you can see that this thing is hanging all the way down.
And so when I clip it to this, I can show you, you can see how that
carabiner wants to sit, but once there's a force on it, it's going to pull like
this and there's no shape to keep that cross loaded, right?
So I'd say this is good enough.
If it breaks, that's even more interesting.
Oftentimes I'll slide this down.
So the button knot isn't getting smashed up against the tree right behind this, or
I do want that in order for it to have some padding.
So it doesn't smack this against the tree.
Actually, I actually really liked that idea.
That's good.
The platforms I'm standing on are just L brackets and two by twelves that I cut.
It's not super sophisticated, but it does make being up here easier.
And this is the only part of the videos that you actually see.
Three, two, one.
You know how I said this never comes off?
Um, it looks like it did.
So you can see that this bounced up, which is fine and it's ready to come down.
And that weight is going to allow it to come through the pulley
as soon as we release this side.
So I'm going to go back down there and evaluate.
That was a perfect descent.
That joke is getting old.
I know the paracord, by the way, in case you didn't know, is what keeps the
perfect descent, uh, retracted during the times I'm not using it.
I didn't break it too bad.
It's still functional.
Uh, 12.3.
That's 50% of what it's rated for.
It's rated for 22.
And then we just make a bunch of conclusions as if we know what happened.
Ready?
It's ironic.
This did not stay in the catching area.
What I'm trying to show you how good of a thing we created was we
did not break the carabiner.
I can not tell you how excited I am about that, but we can
identify what end it broke on.
It doesn't usually bounce as far when I fluff it up more.
So I think I'm going to get my shovel and rake and make it a little bit softer.
So it's not just, so ladies and gentlemen, you just witnessed nine
seconds of one of my normal episodes.
And you can see that we didn't even show you the entire process in this video.
We've been editing this video too.
These take a while.
Shall we do the nylon sling?
Is that foggy or is that my, you know, the less we say the more comments we get.
That's because your shock loaded it.
It's because it's old.
It's because everyone's probably right.
I don't know where no one is.
So reset is just as interesting.
If any of this is interesting, there you go.
Giving slack and notice it's not coming down.
I would benefit from having more weight up there.
If you motivate it, it does.
I'm going to close those teeth back up.
Keep it right there.
It stays fine.
The problem is that dummy is heavy.
And we got to move it back over here.
Now, not as strong as I look, assuming that I looked strong, 150 pounds.
That's not, it's not heavy enough to test things.
You're supposed to do 80 kilograms.
That's why his 80 kilograms would be more.
This is just a video of me bitching about all the comments I've ever had.
I think so.
Okay.
Clicked, pulled, nothing's cross loaded.
There we go.
Back in business.
I could just recycle the video footage I did earlier.
I won't do that to you guys.
As far as I lift it so we can put on the nylon sling.
So these slings were left in an attic for 20 years, very hot attic.
So we'll see if this degraded as much as that one did.
Okay.
So that's ready again.
Super close enough.
Okay.
We're all set up again, but it sits a little bit better.
Like this is how I kind of want it to sit.
Each time I do the sample, this it's good enough.
It'll rotate up when that happens.
Hopefully that doesn't pop off.
I pushed it down pretty good this time.
And this is orientated the way I need it.
And that's the situation happening.
Three, two, one.
Oh boy.
13.21.
So why don't we try to break this lane?
Well, there's two ways we can do it.
We can drop something heavier.
As you can see, that would be difficult to change the weights or to lift and
manage and just manipulate that up there.
And the other thing we can do is drop it further.
So in that case, we could drop the industrial sling attached to it and get
a lot more speed and momentum, giving it like a higher fall factor more, more or
less, uh, that still might not break it because it's an island sling.
It might stretch.
And so sometimes it's really hard to break things and drop tower.
It's nice to just either compare things like the Dyneema versus
nylon, or just see what will happen.
There's usually a lot of variables, a lot of swinging around, a lot of jerk
pulling and without a really fancy machine that just eliminates all that.
This is a amazing how much information we can get from just a tree.
Now I could not have built this without having built the thing in Lodi.
And I still have access to that.
If there is value in, uh, maybe introducing swing, because the way I
built that is that we can move the lift point up further away and actually
introduce the swing in there and it has space underneath, whereas this typically
avoids hitting the tree, mostly when it just breaks the sample, please be safe.
I think that hopefully that's the moral of the story here.
But ideally the dream is to, uh, have a space and a large warehouse someday
that we'd be able to have an indoor drop tower, but a lot of indoor drop
towers, they only have like 10 feet of space to drop things.
And by the time you add soft shackles and line scales and pulleys and dummies
and carabiners and all this stuff, like it's almost 10 feet by itself.
So, uh, you can make compact versions, but you're really, you're, you're
not testing nearly as much.
And in theory, I could go higher up in this tree if I really wanted to.
I think we can do enough with just the way it is a ton of information on
the line scale three product page.
And we also have a way to make graphs.
If you wanted to log your data, you can drag and drop it, boom, right on the
website and it spits it out automatically.
It took like two years to get that to happen.
And you can get that.
If you sign up for emails down the welcome email page, and this also is
going to have a bunch of information about it and the product page as well.
I'd like to know your feedback on if this is something you would use and buy.
Um, and where you see this being helpful, the Ronin it's almost $4,000.
Um, but I believe this is, I think 1500.
So it's a lot cheaper if you're using it for things like the Ronin.
Um, but if you're using it like a winch, let me know.
I'm curious to see if this is something we should pursue.
And if you guys show enough interest, I will break test this and find out the
limits of it and maybe even open one of a lot.
Anyways, sign up for emails.
A lot of good stuff goes out on Saturday that you might've missed during the
week since we post so much now.
Cheers.