Terminologies

IIT Roorkee July 201
61 followers
2 Video Views·Dec 4, 2023
Prof. Shabina Khanam
Department of Chemical Engineering
Indian Institute of Technology Roorkee
Welcome to the fourth lecture of week 1 and this lecture is based on terminologies.
Whatever terminologies we will consider in designing that we will first discuss that
how to select these terminologies or these parameters and then we will go for detailed
design of the pressure vessel okay.
So let us start the terminologies.
So, here I am having main terminology which to be used while designing.
So the first one is the maximum working pressure, then design pressure, design temperature,
and then design stress, corrosion allowance and weld joint efficiency factor.
So, all these terminologies we use in designing, and therefore it will be good if we see how
these terminologies should be selected in designing.
So, let us start with the first one, which is on maximum working pressure.
So, maximum working pressure is the maximum gauge pressure that is permitted for the vessel
in operation, okay.
So the maximum working pressure is the maximum operating pressure you can understand and
that should be given in gauge, and why pressure is considered in gauge, that point we will
discuss when we derive the expression for designing of pressure vessel okay.
But here you should understand, what is the maximum working pressure is, that pressure
which should never increase while operation.
So, maximum working pressure is that pressure, which is the maximum possible value of pressure
which we can face during the operation.
Now, for example, if I say that the system is being operated at 2 meganewton per meter
square and some variation also may be found like 2.1, 2.05 like that, so the maximum possible
value we can observe in the operation that should be considered as maximum working pressure,
and if it is given in absolute, we should convert that first into gauge before using.
So, this pressure limit should never exceed for a vessel during the operation to avoid
failure of the vessel.
So failure of the vessel will occur when pressure exceeds the maximum allowable pressure value,
and therefore we need to consider that value as the base for designing, and it is determined
by the technical requirements of the process.
It means for each process we already know what should be the pressure condition, what
should be temperature condition, but in that pressure, further we will see how much variation
I am observing during the operation because the value will not be fixed at one magnitude
only.
It will keep on changing.
So, what would be maximum possible pressure that we consider as maximum working pressure,
okay.
And the pressure including the static head is used in design calculation of a vessel
for purpose of determining the minimum thickness of various components.
So, along with operating pressure, we also need to focus on static head.
I guess you understand, let us say up to certain height, liquid is filled and whatever rho
gh for that, that we will consider as static head, so that should be added to operating
pressure and that should be considered while designing also.
So, one is operating pressure, second is the static head, so both we need to consider.
Now, here in this slide, we have design pressure for vessel subjected to various pressure conditions,
okay.
Now, why we have defined maximum working pressure, maximum working pressure is the maximum possible
value of pressure found or observed in the process, okay, and then based on that we will
calculate the design pressure.
Design pressure value should be slightly more than the value we can obtain during working
because we need to keep certain safety margin okay.
So, as far as design is concerned, we consider usually value higher than that at which we
need to work, okay.
So, here we have this table, where case 1 is basically whether vessel under internal
pressure okay.
So, internal pressure is PI, now what is the meaning of internal pressure and external
pressure.
This internal pressure we have already discussed in membrane stresses also, so basically internal
pressure is when the pressure inside the equipment is higher than the atmospheric pressure or
higher than the outside pressure that we can call as internal pressure condition.
If the system is being operated at vacuum, so obviously inner pressure would be lesser
than the outside pressure, so in that case condition would be external pressure.
So, this internal as well as external, these both are defined based on whichever pressure
is higher, okay.
So, case 1 is having vessel under internal pressure.
So when I am having pressure, PI, inside the design pressure should be 1.05 * P m wor g
i.
So, 5%, then this, what is this, this is P that is pressure, maximum operating pressure
or work is there, so maximum working pressure in gauge internal, getting.
So, considering this, whatever internal pressures are there, we need to consider that in gauge
and then 5% extra I have to take as design pressure for case 1.
Case 2 says that vessel under internal pressure PI and static pressure due to liquid head,
P st L, P st is nothing but the rho gh.
Here we have 2 cases, first is when static head is greater than 5% than maximum working
gauge pressure.
Gauge pressure is given basically internal pressure and if static head is 5% more than
that, then design pressure should be maximum working gauge internal plus P st L. Static
head will be added to maximum working gauge pressure internal.
If static head is less than 5%, then maximum working gauge, it should be 5% extra to maximum
working gauge pressure internal.
Now, we have case 3 where vessel subjected to inside vacuum and external pressure, P
e or both.
If this is the situation, case 1 is there, where P e is equal to P atm that is external
pressure, e resembling to external, so P external will be equal to atmospheric pressure and
inside is P vacuum, so inside if I am having vacuum and outside is atmospheric pressure,
so obviously atmospheric pressure is more than the vacuum.
So in that case, the condition would be of external pressure condition okay.
So, in that case, if P is equal to P vacuum and this vacuum corresponding to vacuum pressure,
we consider pressure in absolute.
So, 1-P absolute would be the design pressure.
If external pressure is more than atmospheric pressure and vacuum is 0, it means internal
pressure is atmospheric, but outside is more than atmospheric.
So in that case we consider pressure as 5% extra than maximum working gauge pressure
external.
And further, if I am having a condition like external pressure is greater than atmospheric
pressure and P i is equal to vacuum, it means outer we have more than atmospheric and inside
we have less than atmospheric that is vacuum and that vacuum we consider in absolute and
that 1-P absolute plus 5% extra than maximum working gauge pressure external.
This whole value we will consider as design pressure.
So, in this way, we select design pressure in different conditions, so this is very important
terminology while designing.
Now we have the design temperature.
So, what should be design temperature, why is it required?
It is required to find the allowable stress of the material.
It is important to find the allowable stress of the material of construction.
So, we need to choose the material of construction and then we have to see the value of allowable
stress and allowable stress varies with temperature.
Therefore, it is important to first find out the temperature, so it is important to find
out first the design temperature and then based on that we go for the allowable stress
value.
What is allowable stress that we will discuss in subsequent slides.
So, what should be the design temperature, the temperature used in design shall not be
less than the metal temperature expected under operating condition for part considered.
What is the meaning of this.
For example, if the system is being operated, let us say at 300 degree Celsius and metal
will acquire some of the temperature that may be slightly less
than the operating temperature because of conductivity value, but design temperature
should not be less than that temperature.
Let us say 300 is the operating temperature and system is acquiring 290 and 280, so the
temperature we will choose for design should not be less than 280 or 290 as the case may
be.
And further, in no case shall the temperature at the surface of metal exceeds the maximum
temperature listed in the stress table of the material okay.
So, for each material we have permissible temperature value as you can see from this
table for carbon, steel and other alloys.
We have maximum permissible temperatures; these values are based on the melting temperature
of the material, so these are the maximum possible values for material to be considered
in designing.
So, you understand.
Here I am having 2 limits, first is the lowest possible limit.
It means whatever temperature metal should observe, at least that temperature we will
consider as design temperature or that design temperature should not exceed the maximum
permissible temperature defined for that particular material.
So, considering these values, we have defined lower as well as upper limit of the temperature.
And when the occurrence of different metal temperatures during operation can be definitely
predicted for different zones of the vessel, the design of different zones may be based
on their predicted temperature.
What is the meaning of this.
For example, different sections, different components of the pressure vessel may have
different temperature experienced.
So each component will be designed based on respective temperature and then we will consider
that as final design of the pressure vessel.
Here, I am having the table to choose the design temperature for different parts or
different conditions.
The case 1 should be unheated part.
It means heating is not provided, material is available at a particular temperature.
In that case, highest temperature of stored material can be taken as design temperature.
Further, I am having case 2, which is basically used for body parts, heated by means of steam,
hot water or similar heating media, okay.
So if heating is involved in the system, then highest temperature of heating media, that
is the maximum possible temperature in the system.
So that we will consider for designing, or 10 degree higher than the maximum temperature
that any part of the body is likely to attain in course of operation.
So, whatever would be higher among these that we will consider as design temperature for
case 2.
Case 3 is the vessel where direct heating is employed by means of flue gas or severe
exothermic reaction.
In this case, we have first case when vessel is heated.
In that case, highest temperature of inside material plus 20 degree minimum we need to
take as design temperature.
Now, what is the meaning of shielding?
Shielding means when the vessel is insulated, in that case, highest T inside the material
plus 20 degrees we will add as the minimum design temperature.
And if vessel is unshielded or non-insulated, in that case highest temperature of inside
material we need to choose plus 50 degrees we need to further add.
So, in this way, we choose the design temperature, but in no case design temperature should be
less than 250 degrees Celsius.
That is the guideline when temperature is coming less than 250, at least you take value
of design temperature as 250 degrees Celsius, and this is because allowable stress value
is started from 250 degree Celsius.
That further we will discuss in detail when we will discuss the allowable stress as a
terminology.
Now, next terminology we have is the design stress, so let us define this.
The maximum stress permissible at the design temperature for any specified material, okay.
So maximum stress permissible, what is the meaning of that.
It means, when I am operating with any pressure it will create some stress in the material.
So we should consider maximum possible stress that can be created in the system.
That we have to consider as a reference point, okay.
Now, if a member is so designed that the maximum stress as calculated for expected condition
of service is less than some certain value, the member have a proper margin of security
against damage or failure.
What is the meaning of that.
If member is so designed, member means what.
Member means the pressure vessel, the object which we need to design.
So, if member is so designed that the stress whatever we are considering in design that
should be slightly higher than the maximum permissible stress in the system.
Are you getting this.
This is the maximum permissible stress in the system and we are considering this as
a design stress okay.
We are designing at this level.
So, what I can say that, this much difference we can consider as proper safety margin, so
failure will not occur in that case.
So, this value, here I am operating, here I am designing, so this particular value will
be known as design stress or allowable stress.
Allowable stress we have discussed many times in previous lectures, but here I am defining
it.
It is slightly higher value of stress than the value at which system is operated.
And further you should keep in mind that this allowable stress should be less than the damaging
stress.
What is the damaging stress.
Damaging stress is the stress where permanent failure will occur.
So, allowable stress value would be slightly lower than the damaging stress and I am operating
the system at this level.
So this is the operating condition, this is design condition and this is the failure condition,
so you have this much safety margin, okay.
So you can consider here maximum possible stress during the operation.
It is less than the designing stress or allowable stress, and this is further less than the
damaging stress.
So, here, until unless the stress will not reach the damaging stress value, failure will
not occur, and we are designing the system to sustain slightly lower value of stress,
okay.
So, here this is different than the temperature and pressure.
In pressure, we have maximum operating pressure value or working pressure value and we have
design at slightly higher value than that.
And similar observation we have seen for temperature, but here, at which level it is damaged, we
will design at this level, so that we can consider sufficient safety margin.
So, design stress is less than the damaging stress so as to avoid uncertainty to the conditions
of the service, non-uniformity of the material and inaccuracy of stress analysis.
So, considering that uncertainty, we have considered design stress lesser than the damaging
stress and the ratio of these two will be defined as factor of safety.
So, factor of safety or design stress factor will be defined as damaging stress divided
by design stress and that should be greater than or equal to 1.
So, in this way I choose the design value.
And if you see, here we have allowable stress values for ferrous and nonferrous material.
Here, the first column speaks about different material, IS stands for Indian standard and
here we have different codes for different material, these are basically ferrous and
nonferrous material.
And according to this number and grade, material is specified, and here we have allowable stress
value for different design temperature.
So, you see the minimum values available at 250, and therefore design temperature should
not be less than 250.
And as we can keep on moving towards higher temperature, you can see value of allowable
stress will keep on decreasing, okay.
Because when temperature exceeds, it is more prone to fail; therefore allowable stress
value at higher temperature is less than in comparison to that value at lower temperature.
So, you can choose allowable stress value based on such tables.
Now, next terminology we will discuss is corrosion allowance.
Corrosion allowance, I guess yes you understand, that represent all type of damages occurring
in a metal sheet that collectively called as corrosion allowance.
So, whenever the word corrosion is used in the code, it shall be taken to mean corrosion,
oxidation, scaling, erosion and all other forms of wasted.
What is the meaning of corrosion.
When system is being operated with the fluid, so continuous contact of fluid and metal takes
place, so it makes some reaction with the metal surface and that reacted material, that
material is deposited on the surface of the vessel and that is called as corrosion.
What is oxidation.
When metal is coming into contact of the moisture or water, it reacts with that to make the
iron oxide and that we call as oxidation.
Next, we have the scaling.
What is scaling.
Scaling is also called as fouling where material deposited over the surface of the metal.
Now, why it happens because usually we have observed that solubility of a component in
a solution increases when the temperature increases, okay.
But there are certain components like calcium iron, magnesium iron, and all these components
have the tendency that after certain temperature, instead of increasing solubility, solubility
will keep on decreasing with increasing temperature.
So, once solubility will keep on decreasing, they form lumps and they deposit it over the
surface of the metal and that forms a scale or that foul the system.
Next, we have the term erosion.
Erosion means after continuous operation when high velocity fluid pass through a metal sheet
continuously, then some of the metal part will mix with the solution and it will move
with the solution.
So it means removal of material from the metal surface is basically called as erosion.
So, all these type of wastage we have considered in single term and that term is basically
corrosion allowance, which we will use in designing.
So, here you see all these factors we have already discussed to define the corrosion
allowance.
Now, additional thickness to allow for corrosion.
Why this additional thickness is required.
Because, when we design a system, okay, that you must have seen in membrane stress expression
and you will see further in subsequent lectures also that whatever thickness we calculate
from the expression that is the minimum possible thickness.
It means to withstand that pressure that much thickness is required and that thickness should
remain as it is throughout the life of the vessel.
However, when we consider corrosion and other type of wastage, after continuous operation,
metal becomes weak, so we need some additional thickness to the thickness which we have considered
from the expression and that additional thickness as called as corrosion allowance.
Because after continuous operation, if damage will occur, damage will occur only in that
particular thickness which we have added to the corrosion, and whatever is required for
operation to carry out, that is the minimum possible thickness, it will remain as it is.
So, that corrosion allowance we need to decide and then that corrosion allowance we will
add to the minimum thickness.
So, here whatever we have discussed is mentioned.
Here, I am having a table to have the corrosion allowance for different cases.
Case 1 says for carbon steel and cast iron pressure part.
For chemical industry where severe conditions are not expected, corrosion allowance of 1.1
mm we consider.
Further, if we are considering petroleum or petrochemical industries where severe conditions
of damage or wastage are expected, in that case, we consider 3 mm as the corrosion allowance.
Case B is for stainless steel and nonferrous part.
For this case, no corrosion allowance will be used because stainless steel will not have
the tendency to form deposit or to have corrosion.
Therefore, corrosion allowance is not required when we are preparing the vessel with stainless
steel material and nonferrous.
Case C is when wall thickness is greater than 30 mm, then corrosion allowance is not required
because that 30 mm is sufficient thickness and that is very huge thickness.
So In that case, we do not add corrosion allowance because that thickness is sufficient enough
to sustain for longer time.
So, in this way, you find out the corrosion allowance.
And final terminology we have is the weld joint efficiency factor.
So what is weld joint.
When we prepare any vessel, it is prepared with metal sheet.
So what happens.
Usually metal sheet is basically rolled if I am preparing for cylindrical vessel, vessel
sheet we found in rectangle form.
It is rolled and then we weld at one point, so wherever I am welding the metal sheet that
joint becomes weaker in comparison to continuous sheet because that joint will face or will
go through very high temperature with welding, which makes the material of that joint very
weak.
So, the ratio of the strength of weld joint to the strength of the plates welded is weld
joint efficiency factor.
As we have already discussed that wherever welding will occur, that material at that
particular section or particular location becomes weak in comparison to material available
in sheet where welding is not done.
So, the ratio of these two will be defined as joint efficiency factor.
Now, before defining this joint efficiency factor, let us have a look on how many types
of joints occur in a pressure vessel.
So, here you see in this diagram, we have the pressure vessel, okay, and here we have
welded joint location typical for categories A, B, C, D.
We have 4 categories and through these categories we define different types of welded joints.
So, let us start with first one that is A and it is used for longitudinal welded joint
okay and this is basically the longitudinal welded joint.
It means when I roll the sheet and then weld along the length, it will be called as longitudinal
weld joint and denoted by A.
And in this diagram, if you see here, A is given, this is wrong, this is not correct,
okay.
So, A is this.
B is basically defined as the circumferential welded joint.
If the length of vessel is very high, we need to prepare the vessel into 3 connections.
So, if I am having one cylinder, second cylinder we need to add through circumferential joint,
so that will be called as point B. Now, I am having point C, where welded joint connecting
flanges.
This is basically the flange where we cover the mouth of the nozzle using flange.
So connection of this vessel with the nozzle, it called as connection C or joint C. And
when nozzle is connected to the head, you see, so all these A, B, C, D are different
types of connections used in pressure vessel manufacturing.
Now, I am having a table which speaks about joint efficiency factor for different conditions.
So, if you see this table, here we have class of vessel, class of vessel will be class 1,
class 2 and class 3, and for these classes we have J values in this table.
And if you see this first column, it will speak about different types of welding, okay.
So, let us discuss first different types of welding and then we will discuss different
types of classes for vessels.
So first one is double welded butt joint with full penetration.
So as far as joint during welding are concerned, there are certain standard joints.
The first joint is the butt joint means, when I am having 2 metal sheets, I am placing these
2 metal sheets side by side and I weld it, okay.
So, this is basically called butt joint when the sheets are kept side by side, okay.
Now, here I am having double welded butt joint with full penetration.
So here side by side I am keeping, here I am welding, and from bottom also I am welding,
and I will ensure that whatever material through welding is depositing over here that should
penetrate fully.
Next, we have the single welded butt joint with backing strip.
Butt joint is what, these 2 metal plates are kept side by side, from one side we weld,
and from bottom we put a metal strip, so that we call as the backing strip.
Next, I am having is single welded butt joint without backing strip, so that would be butt
joint with welding at 1 side only, so that would be single welded.
And then, we have the single full lap joint.
So lap joint is basically when this is metal sheet, this is metal sheet, when we overlap
metal sheets slightly and weld from this and weld from this, so this is basically lap joint.
This is butt joint, this is lap joint, this is T joint, and this is edge joint.
In this way, different types of joints in welding are defined.
Now, what is class 1 vessel.
These vessels do contain lethal or toxic substance or to be operated under severe condition.
If conditions are very severe, we go for class 1 vessel and it has fully radiograph joints.
Minor defects are also not allowed.
So what is fully radiograph joint.
That I can make you understand if you consider this as my hand, and when I am passing through
x-ray from this hand, how you can see the x-ray, wherever I am having the bone, okay,
there I am getting white section.
White section will be resembling to solid part, however, where I am having the mass,
which is not as solid as bone, there we have some blackish printing, okay.
So, fully radiograph joint means, we make the joint okay and then we pass x-ray through
this and we see the image.
If that image will have all white lines, it means the joint is fully radiographed.
Otherwise, if it is having minor defects or the welding is not done properly, it will
show black sections along the welding.
So, if that happens, it means it has minor defects.
So, for class 1, where minor defects are not allowed, we go for double welded butt joint
with backing strip with J value 1 and single welded butt joint with backing strip can also
be used where J factor is 0.9.
These 2 joints are not allowed for class 1, and similarly class 2 is used for medium duty
operation.
Most of the chemical equipments are involved in this category.
All longitudinal and circumferential joints are spot radiographed.
Spot radiographed means where I am having a few black spots in x-ray, so that may be
considered with minor defects.
The thickness should be less than 38 mm, if that is there, J factor for these 2 joints
are given as 0.85 and 0.8.
And then we have class 3 vessel where light duty operation is carried out and thickness
should be less than 16 mm, and here we use all types of joints and respective J values
are given in this table.
So, here we have discussed different terminologies and these terminologies we will further use
in designing.
And these values of joint efficiency factor, you can also see from table 1.1 in code IS:
2825-1969.
I will speak when we solve the problem that how you need to use table B1 or how you need
to choose other terminology, that we will discuss when time comes.
And here, I am having some of the reference books that you can follow for these terminologies
and here we have the summary of the video.
In this video, in this lecture, terminologies used in mechanical design of equipment are
discussed.
While designing of equipment, how to select design temperature, design pressure, allowable
stress, these are described.
Causes of corrosion are briefly discussed and different classes of vessels are discussed
with respective joint efficiency factor.
So, using these four points, I am completing this lecture.
So, that is all for now, thank you.
