Complete House Wiring from Room to MCB Box @ElectricalTechnician

Friends, in today's video, I will tell you how to wire any house. Friends, the wiring of our house is the same. Whether it is the wiring of the kitchen, the wiring of the room, the wiring of the hall, or the wiring of the washroom will be the same. You just have to keep some things in mind. What things to keep in mind, how to wire, let's understand this. First of all, what I am going to do to you, this is my room. I will tell you the wiring of this room one by one. How will the wiring of this room be done? If you have learned this, then you will be able to do the wiring of the rest of the place easily. So, to do the wiring of this room in my room, first of all, what we will do is our switchboard. We will first clean all the plasters in that switchboard. Means, first of all, we will clean our switchboard. Apart from this, we will also clear the deep box. Along with that, we will also clear the ceiling fan box. After clearing, we will insert the spring here and check whether our conduit pipe is completely clear or not. If we insert the spring, then the spring should go to the other side. Means, our spring should go to our deep box or our other switchboard. We will check all the conduit pipes once so that our wire does not get stuck somewhere while wiring. If all our conduit pipes are ok, then we will start wiring in this condition. So, whenever we go for wiring, first of all, let's see how many points of light, fan and power socket are there in our room. So, as you can see, there is a point of light here in this room. Apart from this, there is a point of light here and a point of light there. Means, we have to connect three lights in this room. Apart from this, there is a power socket here and a fan connection will be given here. So, in total, we will have to connect three lights, a power socket and a fan in this room. Now, first of all, what do we do to do wiring? The material of our switchboard and light, like our plaster, we clean it first. After cleaning, we will first see which is the corner of our light. We start wiring from the corner part. Like all the switchboards of this room, all the switchboard connections will be done from this switchboard. So, to do wiring, first of all, we will use a ring like this. We put this ring inside the pipe and insert it so that there is no plaster inside our pipeline. Means, our pipeline is not clogged. We will check it first. So, the power supply will come to this point of light through that switchboard. So, what we will do is, we will insert the spring in this point of light. Now, we will insert this spring inside it. After inserting, we will check where our spring is going. So, to provide power supply to that light, the wire will come from this fan box. And the connection of the fan box is done directly with the switchboard. One thing you will see here is that a conduit pipe has been inserted from this light, which is connected to this switchboard. Means, the wiring of this switchboard will be done from here. So, the wire that we will insert here, the power socket wire and the wiring of the light should also be there. Now, you can see that we have removed the spring from here. And after removing it, we will put it straight down. Now, what we will do is, we will tie the wire in this part of the spring. Means, we will insulate it with tape. At the moment, you can see that I have brought so much wire in my hand. Now, let's understand the work of all these wires. See, we are using that switchboard to supply phase to this light. So, a phase supply will come here. We will give the power supply to this light directly from this switchboard. So, we will put the neutral wire separately here. So, this red wire will be used to provide power supply to this light. In addition to this, the power supply will come from the MCB box in this switchboard. Means, the main power supply will come in this switchboard. So, for this, we have used a yellow wire for phase supply. This wire is 2.5 mm. In addition to this, I have used a blue wire for neutral power supply. So, the neutral power supply will come through the blue wire. And in this switchboard, we have to provide earthing. So, for that, we have used a green wire here. So, the power supply will come to this power socket through the main switchboard through these three wires. In addition to this, there are three more wires here. These three wires will be used to loop from here to that switchboard. Means, we will use these three wires to provide power supply to the switchboard of our lighting. So, we tie all these wires here with the spring. So, as you can see, I have covered the whole spring here so that the spring does not get stuck. Along with that, I have also tied the whole wire. Now we will pull this spring from there. So, as you can see, our whole wire has gone from here. Now, what we have to do here is to cut the wire that will be used to provide power supply to this point of our light. I have cut this wire here. After cutting, we will make a small joint in it so that our wire does not get inserted inside. So, this wire will be used to provide phase supply to this light. We will provide neutral power supply to this light directly from there. I will tell you a little further about this. At the moment, we have placed the whole wire in the place of our ceiling fan box. Now, the wire will go from this place to that box in the ceiling box. So, what we are going to do is, we will take the wire from this point of the light and connect it to it. So, for this, I have used the phase supply wire and the neutral supply wire here. I will tie these two together with the spring here. So, I tied these two wires with the spring. Now, I will bring the other end of the spring here. And I will insert the spring inside this point of our light. You can see that our spring has come there. So, we will pull the wire from there. Now, after pulling this wire, what we will do is, we will connect both the wires with these wires and take them forward. Now, we will use the same switchboard to turn off this point of the light. So, let's insert the wire from here and take it there. So, to take the wire, first of all, I start inserting the spring from here. So, these two wires will be used to provide power supply to this light. In addition to this, we will use the phase supply to provide power supply to this switchboard. This neutral power supply will be used. So, just for phase supply, we connect a single wire here with it so that the wire goes with it. After connecting, I will insert it from here. So, we have inserted the wire from here. You can see that our wire has come there. Now, we will do the measurement here that how much wire will go there. After that, we will cut this wire. As you can see, we are doing the measurement there. So, to do the measurement, we will measure the wire here. After that, we will cut it. So, we have measured the length of the wire. After measuring, the phase supply wire of this point of the light will be used for this light. So, we will cut it here. So, we have cut this light wire here so that it comes to this point. Now, these two wires will come to this switchboard. So, we will measure its length here. After measuring, we will cut it here. So, I will cut this much here. I have cut it here. After cutting, we will bring these three wires from here and bring them here. These two wires will come down and this wire will come only to this point. Now, you can see one thing that we have to provide light to this storeroom. So, to provide light, we have to take the wire from here. Then the wire will go back from here. So, I will insert this spring here again. So, we are inserting the wire for the storeroom here for phase supply and neutral supply. And we will pull it from here and bring it back. This wire will go to this switchboard. So, we will do the measurement of the wire here. We will pull this much wire. After that, we will open the spring from here. So, I will insert all these wires into the flexible. And after inserting, I will bring it here. So, I have inserted it here. After that, all these wires will go inside it. Now, we will remove the wire of this light from here. And we will collect it here and leave it like this. After this, the rest of the wires along with this wire, a neutral wire of this pointer will go from here. So, I will take another wire here. And I will connect it here. So, I have used an extra neutral wire here, which will come for this light. Now, I will insert all these wires from here. And after inserting, all our wires have come here. Now, it will go to our switchboard from here. One thing you can see here that there are already three wires here. These three wires will go to our washroom. There is a light behind it. So, we have already wired it. Now, I will pull out these three wires from here. After pulling out, the wiring here is complete. Now, we just have to cut this neutral wire here. This wire will be used for our neutral power supply, that too for the light. So, we have wired this light and switchboard. Now, we have to insert all these wires and take them to our switchboard. But one thing you can notice here that these three wires will be used for our incoming power supply. This means that the incoming power supply provided to the power socket will be provided through these three wires. So, we have to take these three wires to the MCB box. So, there is a separate conduit pipe for this. So, we will put it aside here. Now, we will insert all these wires from here. And at the time of inserting, we will connect this wire with it. We will connect this wire with it because we have to provide power supply to turn on and off the ceiling fan. So, I will use this wire to turn on and off the ceiling fan. Apart from this, I will use a white wire here, which will be used for the inverter. This wire will go to our switchboard. This means that this wire will be used to provide power supply to the lighting switchboard. So, I will also connect this together. Now, to connect all these wires to the switchboard, I will insert the spring here first. So, we have connected the inverter wire with all these wires and the ceiling fan wire. After connecting all these wires, we will also connect the spring here. Now, we start pulling this spring and insert all the wires. So, as you can see, all the wires have been inserted from here and all the wires have come out from there. Now, what we will do here is that we will peel off the wire from the neutral power supply of this light. I have removed the insulation of the wire here. After removing the insulation, I will take a black wire here and connect this wire with it. So, this wire will be used for face supply and this will be the neutral power supply for our ceiling fan. Now, I will tie these two together and leave them here. Now, we have put all the wires back. Our conduit pipe has come from the back for this switchboard. So, we will insert this spring from here. After inserting, you will see that our spring will come in the switchboard here. Now, this switchboard is the second switchboard behind it. So, we will take the wire through it to this side. So, here I put the flexible pipe so that our wire does not get cut and I will take the wire from inside it. So, as you can see, all our wires have been inserted from here. So, with this switchboard, we will turn on all the lights and turn on the ceiling fan. So, all the lights and ceiling fan wires have gone from here. Apart from this, the power supply of our switchboard will come from that switchboard. So, we have looped a wire from there to here. Now, we will leave all these wires here. After this, we will connect all these with our switchboard. So, I will remove the spring from here. Now, these four wires, in which the wire for face supply, the wire for neutral supply, the wire for earthing and the wire for inverter, we will have to connect all these with the MCB box. So, for this, we will insert it from here and take it directly to the MCB box. To take all these wires, I insert the spring inside the conduit pipe here. This conduit pipe will go directly to our MCB box. So, I insert all these wires from here. At the moment, there is a problem that there is a lot of wire inside our conduit pipe. So, it is a little difficult to insert all those wires. So, we will put the spring in reverse here and then pull it out from there. So, I insert the spring from here. So, you can see that we have put the spring in reverse here. Now, we will connect it with our old spring. After that, we will pull it out in reverse from here. So, as you can see, we have brought all these wires to this MCB box. Now, we will leave all these wires here. After that, when our MCB is installed, we will connect it directly there. Now, we have to take all these wires to this switchboard. So, for this, we will insert the conduit pipe from here and take it to this switchboard. But you can see that our conduit pipe is cut. So, we will connect a small flexible pipe here. So, we will keep this flexible pipe here. After that, we will insert all these wires here. So, we put a little tape here to insert. Now, we will also connect a black wire here with all these wires. Which will work as a neutral power supply for this light. So, I will connect this wire here in this way. So, our wire has come here. Now, this red wire will stay here because this light will start from our switchboard. We have to take the rest of the wire there. So, we will insert the spring and take all these wires. So, our wire has been inserted. Along with that, the wiring of this room is complete. Now, the way we have wired this room, we will also wire the rest of our room and kitchen in the same way. As you can see, this is our kitchen. If we want to wire this kitchen, we will bring the wiring of the two points of the light here and there. And we will leave the wire in the main switchboard. Apart from this, there is a power socket here. And there is a power socket here. So, to provide power supply to all power sockets, we will insert the 2.5 mm wire from the power socket and bring it to the main switchboard. Then we will loop the wire from there and take it to the MCB box. Keep one thing in mind. If your load is more, like we connect the fridge and oven in the kitchen, apart from this, we use grinder and many other things in the kitchen. So, if you have to connect a heavy load in your kitchen, then the wiring of the power socket will be separate in this condition. And the wiring of the light and fan will be separate. This means that 6 wires will go from your kitchen. 3 wires will go to the power socket and 3 wires will go to the lighting. The power supply for the lighting will come here. The power supply for the power socket will come here. And we will distribute them separately. After looping the wire, we have brought this socket from the MCB board to the main incoming power supply. This means that the power supply will come separately for the power socket. And the power supply will come separately to connect the light fan. For the power supply for the light and fan, we will use phase supply, neutral supply and earthing. Apart from this, there will also be an inverter wire. In addition, we will use phase, neutral and earthing for the power socket. So, we will do the wiring of the kitchen in the same way as I told you about the wiring in the room. Apart from this, there is another room. We will do the wiring of this room in the same way as we did the wiring of that room. After doing the wiring of this room, we will take all these wires straight to the MCB box. And we will connect it to the MCB there. After this, there is a hole here. As you can see, there is a hole here. We will also connect the four-celling to this hole. So, we left the four-celling wire a little long. So that it can connect to the light. Apart from this, we have also left the fan wire separately here. We have left it separately here so that we can also connect the ceiling fan. A total of three ceiling fans will be installed in this hole. So, we have left three circuits separately here. In addition, we have also connected the power socket here separately. Their wiring will be completely separate. Apart from this, to turn off all the lights, the main incoming power supply on the switchboard will be completely separate. In addition, we also have to connect the inverter to the switchboard for lighting. So, to connect the inverter, we have already connected a separate wire here. So, the same way we did the wiring of the room, the same way we will do the wiring of the kitchen and the hole. You just have to keep in mind that the connection of the power socket and the lighting socket should be separate. In addition, keep in mind how much wire will go from that light. So that in the future, when you go to connect the bulb and fan, there will be no wire that has been left or we have not connected it. So, keep all these things in mind and do all the wiring. So, I hope you liked this video. Please comment and tell us how you liked the video. And if you want to know how to connect the switchboard, and how to connect the MCB in our MCB box, then comment and let me know. Thank you for watching this video.