EC 462 Mixed Signal Circuit Design-CS Stage With Degeneration
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, today we are studying common switch stage with degeneration.
This is the circuit diagram of a common switch stage with degeneration.
The difference between this and the other is that we are using a resistor here.
We are using a resistor called RS.
This is where the transistor is connected to the ground through a resistor called RS in the switch.
In other circuits, the source terminal of the transistor is directly grounded.
In the case of a degeneration circuit, the source terminal of the transistor is grounded through a source resistance.
So, a resistor is placed in series with the source of the MOSFET, which alters the characteristics such as gain, input-output impedance, and linearity.
The purpose of this is to alter the characteristics such as gain, input-output impedance, and linearity of the MOSFET.
Such circuits are called common switch stage with degeneration.
This is the circuit diagram and its corresponding small signal model.
We are applying input to the gate terminal.
The input resistance of a MOSFET is a very large value.
The current does not conduct through this very large value.
If the current does not conduct, it will act as an open circuit.
So, the input terminal is placed as an open circuit.
This is the source of the transistor.
The output of the transistor is the current source.
The current source is gm into V1.
This resistance is called RD.
Since we have neglected the modulation effect of the channel, we are not considering the output resistance RO.
The source terminal of this transistor is connected to a resistor called RS.
This is the source of the transistor.
We are drawing a resistor called RS in this source.
This is the small signal model of common switch stage with degeneration.
This is the figure.
We are not considering the modulation effect of the channel.
We are considering lambda is equal to zero.
That is why we are not drawing the output resistance and the internal resistance of the transistor.
We can write the equation in this figure.
V in is the total voltage applied across this portion and the ground.
The total voltage V in is distributed in two ways.
V1 is applied to the source and gate.
Some voltage is applied to RS.
This is the total voltage applied to V in.
Some voltage is applied to gate and some to RS.
This is the total voltage V in is equal to.
This is V1 multiplied by the voltage here.
The voltage here is the current multiplied by the resistance.
The current flowing through this is the current V in.
This current is gm into V1.
Current into resistance is gm into V1 into RS.
V1 is equal to V in divided by 1 plus gm into RS.
The equation of this voltage is V in divided by 1 plus gm into RS.
If we get V1, we can write the equation of Vout.
Vout is the current into resistance.
Current is gm into V1.
Resistance is Rd.
The direction of the current is opposite.
We are measuring the output voltage across this terminal and this ground.
The current was supposed to flow downwards from this terminal.
The symbol of the current is negative.
Vout is equal to minus gm V1 Rd.
Vout divided by V1 is equal to minus gm Rd.
Instead of V1, we can substitute V in divided by 1 plus gm into RS.
You will get Vout divided by V in is equal to minus gm into Rd divided by 1 plus gm RS.
We got the equation of gain.
The equation of gain is minus gm into Rd divided by 1 plus gm RS.
If we take gm as common from the numerator and denominator,
gm and gm will cancel and Rd will come.
Since gm is common from the denominator, we substitute 1 by gm plus RS.
The equation is minus Rd divided by 1 by gm plus RS.
This is the gain of a common source configuration with degeneration.
The next analysis is to find the gain and output resistance.
We have to find the output resistance.
Earlier, it was easy to find the output resistance.
But in the case of degeneration, it is a little difficult.
But you can apply what you have learned in the network.
It is easy to find.
Next is the effect of transistor output impedance.
We are finding the output impedance of the transistor.
The output impedance has a critical role in degenerated common source.
So it is very important to find the output impedance.
This is the common source configuration with degenerated load.
This is the equivalent diagram.
We are going to find the output resistance in this diagram.
How to find the output resistance?
Ground the input.
Apply voltage to the output terminal.
You have learned how to find the output impedance in the network.
How to find the output impedance?
Ground the input terminal.
Apply voltage to the output terminal.
Ground the input terminal.
Apply zero voltage to the input terminal.
There is no Rg here.
Ground the input terminal.
We have drawn the rest of the diagram.
We have connected the source.
There is a resistor called Rs.
There is a gm into V1 in the output.
We are considering the modulation effect in the channel.
We have taken the R0 resistor.
We are applying the voltage Vx to the output terminal of the transistor.
We don't have to take this.
We don't have to take this when finding the output impedance.
What do we apply to the drain?
We apply a voltage called Vx.
The current that flows through it is called Ix.
This is the diagram to find the output impedance.
Let's look at the rest of the diagrams.
V1 is the voltage.
The total voltage is zero in this terminal.
It is zero here too.
The total voltage is zero.
If the total voltage is zero,
the reverse of the voltage generated here will be zero.
We are grounding the input terminal to find the output impedance.
When the input terminal is grounded,
the voltage across the gate and the source should be zero.
Since the current flows through the transistor,
a voltage will come in Rs.
If the voltage across the gate and the source is opposite to the voltage in Rs,
the total voltage will be zero.
Let's write V1 as minus gm into V1 Rs.
The current that flows through Rs is called V1.
Since we have considered the channel length modulation effect,
this current is the sum of gm into V1 and the current flowing through Ro.
The total current is called Ix.
The current flowing through Rs is equal to Ix.
So, V1 is equal to minus Ix into Rs.
Is it clear?
Since the current flowing through this is Ix Rs,
the total current is opposite to that.
So, V1 is equal to minus Ix into Rs.
Now, what is the current flowing through Ro?
The current flowing through Ro is equal to Ix minus gm into V1.
This is equal to Ix minus Ix Rs.
So, the equation is Ix plus gm Ix Rs.
Adding the voltage drop across Ro and Rs and equating the result to Vx.
Vx is the equivalent of the total output voltage.
So, Vx is the equivalent of the total output voltage across Ro and Rs.
What is the voltage across Ro?
Current into Ro.
Current is equal to Ix plus gm Ix Rs into Ro.
Ro plus Ix into Rs.
So, the current flowing through Ro is equal to Ix plus Rs.
This is equal to Vx.
Now, we can take Vx divided by Ix.
Vx divided by Ix is the output resistance.
The equation is Ro into 1 plus gm Rs.
Vx divided by Ix is equal to Ro into 1 plus gm Rs plus Rs.
If we take Rs as common from these two terms, we get 1 plus gm Ro into Rs plus Ro.
Both are same.
We can use any equation.
Ro is a small value.
So, we can write it as approximately equal to gm Ro Rs plus Ro.
So, we got the equation of output impedance.
So, this is the way to find the output impedance of a common source stage with degeneration.
Now, let's see the two related problems.
1. Compute the voltage gain of the circuit shown in figure if lambda is equal to zero.
2. Neglect the channel length modulation effect.
This is the question.
We have to draw a simplified diagram of this.
We don't have to consider the output impedance because of neglecting the channel length modulation effect.
3. Connect the source terminal of a common source stage with a resistor called Rs.
This is called degeneration.
But here, instead of a resistor called Rs, we have a diode connected load.
This is called diode connected load.
You know the equivalent diagram of diode connected load.
It is 1 by gm2.
This is the equivalent resistance.
Instead of this transistor, we can write 1 by gm2.
Now, we have to find the voltage gain.
We have studied the equation of voltage gain.
The equation of voltage gain is minus Rd divided by 1 by gm plus Rs.
That's enough.
Minus Rd divided by 1 by gm1 plus 1 by gm2.
In the general equation, Rs is replaced by 1 by gm2.
That's it.
This problem is simple.
We have used a source resistor called Rs instead of degeneration.
Here, we have a diode connected circuit.
This is equivalent to 1 by gm2.
Instead of Rs, we have to substitute 1 by gm2.
Next, compute the output resistance of the circuit shown in figure.
If M1 and M2 are identical.
This is the circuit diagram.
This is the equivalent small signal model.
In order to find the output impedance, we have to ground the input.
Everything else is drawn in the same way.
Here, the diode is connected.
But the modulation effect is not neglected.
So, we have to consider R1.
We have to consider the output impedance of this transistor.
The equivalent of this diode is 1 by gm2 parallel to Rout2.
Now, let's look at the equation of Rout.
We have studied the equation of Rout.
The equivalent resistance is 1 by gm2 parallel to Rout2.
Approximately equal to 1 by gm2.
Now, look at the equation of Rout.
Rout is equal to Ro into 1 plus gm into Rs plus Rs.
Instead of Rs, we have to substitute 1 by gm2.
We have studied the equation of Rout.
In that equation, instead of Rs, we have to substitute 1 by gm2.
Now, look at the equation of Rout.
Ro is equal to Ro1.
Now, we have to substitute 1 plus gm into Rs.
gm1 into Rs is equal to 1 by gm2 plus 1 by gm2.
Rs is equal to 1 by gm2.
Here, both the transistors are identical.
When transistors are identical, gm1 and gm2 are equal.
gm1 is equal to gm2 is equal to gm.
So, this will cancel.
Then, we substitute 2Ro1 plus 1 by gm which is approximately equal to 2Ro1.
So, that is the solution to find how we can find the output resistance of a circuit.
We can find the output resistance in this way.
For that, we have to study the general equation.
We have to study this equation as well as this equation.
But, we have to study this equation only for the problem.
If we ask the theory, we have more chances to ask the derivation.
It is a little complicated to find the output impedance.
So, this is a question worth asking.
I hope everyone understood.
See you in the next lecture.

