Mixed Signal Circuit Design - Bandgap Reference Circuit Part 1- EC462 MSCD
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
The analog circuit that we normally use is mostly dependent on voltage and current references.
These references, be it voltage or current, are all DC quantities.
Therefore, it has very little dependence on supply and process parameters.
However, it mostly depends on temperature parameters.
In this lecture, we are going to learn about the design of the reference generator for CMOS technology.
We will mainly focus on well-established bandgap techniques.
In most applications, there are three forms of temperature dependence.
The first one is proportional to absolute temperature.
The second one is constant gm behavior.
The third one is temperature independent.
There are other parameters like output impedance, output noise, power dissipation, etc.
Now, let's see how supply-independent biasing is provided for this circuit.
This figure shows the current mirror circuit.
You can see two circuits here.
Both are current mirror circuits.
The first one is an ideal current source.
It is a current mirror circuit using an I-reference.
The second circuit is a current mirror circuit using a resistor called R1 instead of an ideal current source.
In this circuit, the I-out is equal to delta Vdd divided by R1 plus 1 by gm1 into W by L of second transistor
divided by W by L of first transistor.
This is the equation we derived earlier.
We got an equation with output current variation.
It is clear from this that the output current variation depends on the supply.
It depends on delta Vdd.
What can we do if we make the I-out independent of the supply?
We can say that this is supply-independent biasing.
Now, let's see how we can make the I-reference independent of the supply voltage.
In this circuit, the M1 transistor and M4 transistor work in saturation.
The modulation from the channel is zero.
The output is K into I-reference.
Hence, it can support any current level.
Addition of Rs to define the currents.
Alternative implementation of eliminating body effect.
Assume that λ is equal to zero.
Assume that I-out and I-reference are equal.
The gate source voltage of the first transistor is Vgs2 plus Id2 Rs.
The second drain current is Rs.
Hence, Vgs1 is equal to Vgs2 plus Id2 Rs.
We have studied the equation for gate source voltage.
Instead of Vgs1, we have written Root of 2 into I-out divided by μnCOx into W by L of n plus Vth1.
This is the gate source voltage of the first transistor.
This is equal to gate source voltage of the second transistor plus Vth2 plus I-out into Id2 Rs.
If we neglect the body effect, we get square root of 2 into I-out into I-out divided by μnCOx into W by L of n plus 1 minus 1 by root K.
This is equal to I-out into Rs.
I-out is equal to 2 divided by μnCOx into W by L of n into 1 by Rs square into 1 minus 1 by root K.
We can define the current as independent of supply voltage.
However, this is dependent on process function and temperature.
We have added Rs to the circuit diagram.
Assume that the channel length modulation effect is not zero.
We are going to see how Id and I-out will look like.
We have drawn a small signal model corresponding to the circuit diagram.
That is shown on the right side.
The M4 transistor is replaced by an RO4 output transistor.
The M3 transistor is replaced by an R3 output transistor.
The M1 transistor is replaced by an R1 output transistor.
The M2 transistor is replaced by an M4 output transistor.
We can find the resistance value as R1.
R1 is equal to RO1 parallel 1 by gm1.
Similarly, R3 is equal to RO3 parallel 1 by gm3.
Assume that the voltage is Vx.
The current flowing through R1 is Vx by R1.
The current is Vdd minus Vx divided by RO4 plus Iout into R3 into gm4.
The equivalent transconductance of M2 and Rs is gm2 is equal to Iout divided by Vx.
Iout by Vx is equal to gm2 into RO2 divided by Rs plus RO2 plus gm2 plus gmb2 into Rs RO2.
Iout by Vdd is equal to 1 by RO4 into 1 by gm2 into RO4 parallel R1 minus gm4 into R3 the whole raised to minus 1.
This value tends to zero because RO4 is infinity.
Degenerate assistance of degenerate bias points.
For example, if all transistors are carrying zero current and the supply is ON, the circuit will be OFF indefinitely.
Since zero current supports this loop, it will be OFF indefinitely.
The next circuit is a startup device.
The transistor M5 works as a startup device.
A diode connected transistor M5 provides a current path through M3 and M1 to the ground.
If Vth1 plus Vth5 plus Vth3 less than Vdd, Vgs1 plus Vth5 plus Vgs3 greater than Vdd.
If Vth1 plus Vth3 less than Vdd, Vgs1 plus Vth3 less than Vdd, Vgs1 plus Vth3 greater than Vdd.

