Washing Machine Not Spinning - Replacing Broken Lid Switch

TightWadDIY
899 followers
151 Video Views·Jun 30, 2019
If your washing mashing stops mid cycle and will not agitate or spin there is likely one the following issues happening. Either your lid switch is broken so the washer thinks the lid is open, or your motor coupling has gone bad. This video shows how to replace the lid switch. To see how to replace the motor coupling, click the link below.
Replacing the Motor Coupling - https://www.youtube.com/watch?v=Ldy-vg7rGFQ
To order a new lid switch for your washing machine, use the Amazon Affiliate Link below.
Whirlpool OEM Lid Switch - https://amzn.to/2NohzMg
Welcome back guys, it's the tightwad and today we're working on a Kenmore washing machine
This is specifically a 70 series, but they all function pretty much the same way and have the same parts
It doesn't matter if you have more dials or a few less dials
But if you have the Kenmore or anyone that looks similar to this
This will apply to you
If your washing machine fills up with water and the agitator will not move and it doesn't even sound like it's trying to move
You most likely have an issue with your lid switch. Your lid switch is right here
And when the lid closes this peg here
Pushes the switch down and lets the washing machine know that it's closed so that it'll agitate
Meaning this thing will spin back and forth to move your clothes around and clean them
I've seen some videos claiming that you can replace the lid switch without removing the cabinet from the washing machine
And while it is possible, it's very hard to see what you're doing when you're trying to replace that lid switch
So you can use what you see in this video to attempt that method if you want to
Because I'm going to show you where everything is actually located. I'm gonna be taking the whole thing apart today, though
To complete this repair today
I'm gonna take my washing machine outside so that you can see everything a little bit better
In order to do that, I need to remove the hot and cold
hoses here
Before you disconnect your hoses from the washing machine
Make sure you turn the hot and the cold valve off here or you're gonna make a huge mess with water spraying everywhere
And I need to unplug the washing machine from the wall
So I'm gonna get that done and get the washing machine outside so that you can see a little bit better
In order to complete this repair, we're gonna have to remove the whole cabinet of
the washing machine and
All these Kenmore whirlpool and ropers have slightly different configurations on the front but on this particular Kenmore
there are parts
That clip off from each side here already had them pop free
So they were easy to remove and then there's a screw on each side
Some of them don't have screws here and they have screws in the back instead, but you just have to figure out
What your particular model requires?
So I'm going to remove these screws
And once you get them loosened, you can grab firmly from the back and it should lift up and this whole thing
can rest
Right here on the back just like this
The next step is to remove these clips, there's one on each side
I'm gonna use two hands for this because I'm gonna put my screwdriver down in here and look forward
Lifting up on the hinge and it'll pop right out
Before I unclip the second side here. I'm going to unclip
This connector it should just lift up and pull off. That's the connector that goes to your lid switch
So this one is now free as well, it's okay if they come out they just slide right back in
With both both clips out. I
Can open the lid of the washing machine?
stick my hands inside
And it simply lifts off
The lid switch on my washing machine broke several months ago
You can see that it's just dangling right here and I'll provide a link in the description
Showing how to bypass the lid switch altogether while I have the cabinet off today
I'm gonna go ahead and remove this old lid switch and install this new one that I've already ordered
This is the clip that goes up through the top
this is the
Protective piece that holds all the wiring out of the way
This is the broken clip and you can see that it is attached right here
If we come up to the top, you can see it's just held in by two Phillips head screws
So I'm gonna go ahead and remove these first and we'll get started installing the new one
Under the bottom of your unit, there'll be a green wire running to a screw. This is the ground wire
So we're going to go ahead and remove this on my particular unit. It is a five sixteenths hex nut now
I've got to get this pushed through so I'm going to use a flathead screwdriver on each side
To push in the tabs and it should push right through
And fall through the unit and the last thing to remove it are these two clips there's one here and
One over here that I'm going to pull the wires out of
So I'm just going to bend it back with my finger or with a flathead screwdriver and slide this piece out
Now I'm going to compare my original with the aftermarket one that I purchased and you can see we have
Three wires with the green in the middle on both of them. The clips look the same
So that's good and down here on the other end. It's simply a push switch
All the ones broken both say they're for a half horsepower
So that's good. And it looks like the screw holes are in the same place
So it should go on pretty easily
One thing that is different is the length of the wiring this one. The new one actually came with a really long piece of
Plastic here. So I pulled the wires out of it and cut it with a pair of kitchen scissors and
The wires are a little bit longer, but that shouldn't be a problem
I'll be able to hide them up in there somewhere
Tie them up if I need to so I'm gonna go ahead and get this new one installed
My plan is to do everything in reverse order. So first I'm gonna get the wires in place
And now I'm gonna put this clip up through the bottom and it should just push up and lock into place
Now I'm going to attach my ground screw
And now I can position the clip and insert the screws
And the holes do line up. So that's great
Get those screws nice and tight and I'm gonna test the thing to hear a click
You can hear it click
That's a great sound to hear and the cabinet is now ready to go back on the washing machine
I'm gonna show you how to get the cabinet back on your washing machine
And there's a lip in the front and lips on the side here
the bottom of the cabinet goes under the front of this front lip and
Then the sides sit on top of the side lips
there's also a pin in the front and
The back on each side and that's what keeps the sides of your washing machine from flopping out
So I'm going to slide the front end under the front lip first and then I'm going to position the sides
so I came in with the front side low and you can see that the lip of the
Cabinet is under the black bar
of the frame
So it's got to slide completely under it like that
Now I'm gonna hold my foot against the front so that it doesn't come loose
While I guide the sides down on the clips on the bottom rail
I'm gonna push in and go down and you can see I can tug on that and it won't come out anymore
Then I'll do the same thing on the other side
Making sure that the clip is engaged and you can actually see if you look in
On the other side the clip is engaged there and here as well
So now everything should line up correctly
When I pull this forward, so with that in place I
Can pull everything back in here
This can rest on the back
Don't forget to plug your lid switch back in
these plastic pieces
Should go inside this side of the dryer on both sides
And they'll be held in tight once you get your lip clips on
with the plastic piece in place
Line it up slide your clip in
Then press down
To clip it into place
Do the same thing on the other side?
Press the plastic backing in
Put the clip in make sure everything's lined up
And press it down
If you didn't already do so again make sure that you attach your lid switch here
Now this piece is ready to put back on just slides down with the back rim here over the back
There on mine. There are clips on each side that have very obvious holes that they go in
So the screws go back in the holes on the side to hold this cap on
Now your trim molding goes on it just has clips that snap into place
To test to make sure we what we did worked correctly today
I'm going to set it on spin and pull out the switch
You'll see nothing happens because our lid switch is not pushed in so now I'm going to close the lid
And our unit starts spinning. I'm going to open it up, and we'll see it come to an abrupt stop
So everything is now working if this video seemed to be a little bit more than you're willing to undertake
There is a way to bypass the lid switch without removing the whole cabinet from the washing machine
You can check the description or click the link popped up on the screen now
And it will show you exactly how to do that with a piece of wire
If you found this video helpful give me a thumbs up and subscribe to my channel
I have lots of other appliance repairs as well as many repairs around the home and on lawn equipment
If you have any questions put them in the comment section below, and I'll respond as soon as possible
I hope you guys have a great day
