There are two main reasons your washing machine will turn on but will not spin or agitate.
Scenario 1: If the washer sits idle when it should be spinning and there is no sound, its likely a broken lid switch. The lid switch is a safety switch that prevents the washing machine from working if the lid is open. When it breaks, it already thinks the lid is open. You can bypass the lid switch using a temporary bypass(video here: ) or you can replace the lid switch which I demonstrate in this video.
Scenario 2: Your washing machine sounds like it is trying to spin but nothing is happening. This issue is likely a broken motor coupling. This part sits between the motor and transmission. This videos shows step by step how to take apart your washing machine to remove and replace this part.
You can order the parts you need using the Amazon Affiliate links below:
Welcome back guys. It's the tightwad and today we're working on a Kenmore washing machine
This is specifically a 70 series, but they all function pretty much the same way and have the same parts
It doesn't matter if you have more dials or a few less dials
But if you have the Kenmore or anyone that looks similar to this, this will apply to you
So I was in the middle of a wash and I noticed things sounded funny
you can see we're getting ready to be at the spin cycle here and
I have clothes in here and I'm going to turn it back on for you
And right now the wash machine should be spinning out the water and you can see it's doing nothing
It also will not agitate back and forth
So this particular issue today is that it's trying to spin and I can hear the mechanism
Spinning at the bottom of this shaft here of the agitator
But it is not spinning
If your washing machine fills up with water and the agitator will not move and it doesn't even sound like it's trying to move
You most likely have an issue with your lid switch. Your lid switch is right here
And when the lid closes this peg here
Pushes the switch down and lets the washing machine know that it's closed so that it'll agitate
Meaning this thing will spin back and forth to move your clothes around and clean them
However, if your lid switch is open, it will think that your washing machine lid is open
It will not allow the agitator to spin because it is a dangerous thing
If your arm got down in there, it could potentially cause some harm
Since our washing machine does sound like it's trying to spin
It's most likely the coupler that sits between the motor and the transmission of the washing machine and to get to that
I'm gonna have to flip the washing machine upside down or on its side so that I can show you the part that needs to
be replaced
To complete this repair today
I'm gonna take my washing machine outside so that you can see everything a little bit better
In order to do that, I need to remove the hot and cold
hoses here
Before you disconnect your hoses from the washing machine
Make sure you turn the hot and the cold valve off here
Or you're gonna make a huge mess with water spraying everywhere and I need to unplug the washing machine from the wall
So I'm gonna get that done and get the washing machine outside so that you can see a little bit better
In order to complete this repair, we're gonna have to remove the whole cabinet of
the washing machine and
All these Kenmore whirlpool and ropers have slightly different configurations on the front
but on this particular Kenmore
there are parts that
Clip off from each side here already had them pop free so they were easy to remove and then there's a screw on each side
Some of them don't have screws here and they have screws in the back instead, but you just have to figure out
What your particular model requires?
So I'm going to remove these screws and once you get them loosened you can grab firmly from the back
and it should lift up and
this whole thing
can rest
Right here on the back just like this
The next step is to remove these clips. There's one on each side
I'm gonna use two hands for this because I'm gonna put my screwdriver down in here and look forward
Lifting up on the hinge and it'll pop right out
Before I unclip the second side here. I'm going to unclip
This connector it should just lift up and pull off. That's the connector that goes to your lid switch
So this one is now free as well, it's okay if they come out they just slide right back in
With both both clips out. I
Can open the lid of the washing machine?
It simply lifts off
The piece we're replacing today is actually right here
You can see that it's broken right here in this little crease
But it's the white piece on top this black piece and the white piece on the bottom and it's called the motor coupling
So in order to get to it, we're gonna have to remove the pump and hoses here
And the motor and it sits between the motor and the transmission for the washing machine
This is what controls the agitator back and forth here
So we don't have to remove this but we do have to remove this and this
The next step is to take these two clips off always start on the lower side
when removing clips like this because the upper one has
More tension on it and will hold it in place
so this clip just
Unclips and then turns to remove it and the same thing with the top one
You should be able to do this with your fingers
Unclip it twist it one way or the other and then wiggle it till you can get it removed
And we can just set these to the side
this whole assembly should slide right off and
You should be able to get it bend it over out of the way
And you do not have to remove any of the hoses there now to remove the motor
I need to remove these two screws and they're just quarter-inch screw heads
so I have a
screwdriver here that accepts other types of heads and
They are always a quarter-inch
So I'm going to take these two screws out
And with those off I can either pull these off with my fingers or I can use a
Screwdriver to pry them off again. We're going to remove the one closest to the ground first
Because the top one is going to hold the motor in place
these also unclip and then twist and
Pull out so I'm going to set them to the side
And now I'm going to do the same thing with the top one
And I'm going to hold my hand here just in case the motor loosens and falls it should stay in place by itself though
Now I need to lift the motor up. I'm going to use two hands because it's somewhat heavy
And I'm going to grip it from the very bottom. I'm going to lift straight up
When I remove the motor you can see this piece already fell out
So I'm going to grab the other pieces out of here
And I'll show you what it's supposed to look like when it's new. But first we also need to
Check the bottom side of the motor and it has the other part for this adapter on it. So this is part of it here and
Then this one's actually part of it too. So I'm going to go ahead and remove this as well and it should slide right off
with this off
You can see that there are two flat side and then there's two other sides and those fit right down on these shafts in here
They have two flat sides and that's what makes it spin
I was able to go to my local parts store and purchase this Whirlpool brand replacement
If you follow my videos, you know that I don't like aftermarket parts. I like to buy OEM or the original
Manufacturer's parts. So I'm going to open this and show you what it looks like
Whirlpool remade these with a metal part inside so that the when the stress of turning or agitating
Hits it. It's not going to break the plastic. So these are made to last a lot longer and
It comes with two of them and the black plastic or rubber washer and it doesn't matter which one goes in which side
But they fit together like this
so one goes in one side one goes in the other and they turn back and forth on the shaft between
The transmission here and the motor that we pulled off
So let's go ahead and get this reinstalled to install the new part. I'm going to line up the two flat sides
With the flat sides of the metal shaft and it should start to go on
But then you're going to meet some resistance with it. So I like to take a rubber mallet and
Tap it down
Now I need to get the other half onto the shaft for the motor
and with this one
I'll again tap with the rubber mallet lightly and
I hammer it on until I can see that it is down to the point where the previous one was sitting
I'm not ready to slide the motor back on the transmission
So I'm going to make sure that one of my openings is at 12 o'clock straight up to this side here
And then I'll do the same for the piece here
So when I go to slide it on all I have to do is
Slide it on straight and the slot should go right into the hole
So it slid right on and everything's nice and tight. I can't spin it back and forth. That means it's seated
You can also check from the bottom to make sure that everything appears to be seated properly
Now we're going to complete our steps in reverse order
So I'm going to put the top clamp on first
Sliding it into the hole straight and then twisting it and I'll snap it back on
To the motor then I'm going to do the lower
brace for the motor
Snap it into place
Don't forget to put your two screws back in. So this is where we'll be using the ones with the
Quarter inch head on them and go ahead and tighten those down snug
Don't forget to reinstall the clip
the wiring harness
Make sure it snaps into place
now we need to
reinstall the pump
The little feet from the pump go into these little small holes on the motor if that'll help you line it up, right?
You may have to twist it back and forth slightly
to get the shaft to line up correctly and
We can put these clips back on again. Slide them in sideways then spin them towards the pump and clip them in
one more sideways
Spin it around the face of the pump
And clip them on
At this point if you want to test to make sure that it's spinning correctly
the clip that you removed
When you flip the top up you can take a piece of wire or staple and stick it in each of the outside terminals
on that clip and it will make the washing machine think that the lid switch is compressed and
We can actually plug in our unit and see if it will spin
Ensuring that my hands are clear and nobody's near it
I have the washing machine plugged in and I'm gonna turn it to the spin cycle and pull up on the knob
And you see that our spinning cycle is now working
So now I can reassemble the cabinet and plug back in my lid switch
The lid switch on my washing machine broke several months ago
You can see that it's just dangling right here
And I'll provide a link in the description showing how to bypass the lid switch altogether while I have the cabinet off today
I'm gonna go ahead and remove this old lid switch and install this new one that I've already ordered
This is the clip that goes up through the top. This is the
Protective piece that holds all the wiring out of the way
This is the broken clip and you can see that it is attached right here
If we come up to the top, you can see it's just held in by two Phillips head screws
So I'm gonna go ahead and remove these first and we'll get started installing the new one
Under the bottom of your unit, there'll be a green wire running to a screw. This is the ground wire
So we're going to go ahead and remove this on my particular unit. It is a 5 16th hex nut now
I've got to get this pushed through so I'm going to use a flathead screwdriver on each side
To push in the tabs and it should push right through
And fall through the unit and the last thing to remove it are these two clips. There's one here
And one over here that I'm going to pull the wires out of
So I'm just gonna bend it back with my finger or with a flathead screwdriver and slide this piece out
Now I'm going to compare my original with the aftermarket one that I purchased and you can see we have
Three wires with the green in the middle on both of them. The clips look the same
So that's good and down here on the other end. It's simply a push switch
All the ones broken both say they're for a half horsepower
So that's good. And it looks like the screw holes are in the same place
So it should go on pretty easily
One thing that is different is the length of the wiring this one. The new one actually came with a really long piece of
Plastic here. So I pulled the wires out of it and cut it with a pair of kitchen scissors and
The wires are a little bit longer, but that shouldn't be a problem
I'll be able to hide them up in there somewhere
Tie them up if I need to so I'm gonna go ahead and get this new one installed
My plan is to do everything in reverse order. So first I'm gonna get the wires in place
And now I'm gonna put this clip up through the bottom and it should just push up and lock into place
Now I'm going to attach my ground screw
And now I can position the clip and insert the screws and the holes do line up so that's great
So the screws nice and tight and I'm gonna test the thing to hear a click you can hear it click
That's a great sound to hear and the cabinet is now ready to go back on the washing machine
I'm gonna show you how to get the cabinet back on your washing machine
And there's a lip in the front and lips on the side here
the bottom of the cabinet goes under the front of this front lip and
Then the sides sit on top of the side lips
There's also a pin in the front and the back on each side
And that's what keeps the sides of your washing machine from flopping out
So I'm gonna slide the front end under the front lip first and then I'm gonna position the sides
so I came in with the front side low and you can see that the lip of the
Cabinet is under the black bar of the frame
So it's got to slide completely under it like that
Now I'm gonna hold my foot against the front so that it doesn't come loose
While I guide the sides down on the clips on the bottom rail
I'm gonna push in and go down and you can see I can tug on that and it won't come out anymore
Then I'll do the same thing on the other side
Making sure that the clip is engaged and you can actually see if you look in
On the other side the clip is engaged there
And here as well
So now everything should line up correctly
When I pull this forward so with that in place I
Can pull everything back in here
This can rest on the back
Don't forget to plug your lid switch back in
These plastic pieces
should go inside this side of the dryer on both sides and
They'll be held in tight once you get your lip clips on
With the plastic piece in place
Line it up slide your clip in
Then press down
To clip it into place
Do the same thing on the other side
Press the plastic backing in put the clip in make sure everything's lined up
And press it down
If you didn't already do so again, make sure that you attach your lid switch here
Now this piece is ready to put back on just slides down with the back rim here over the back
There on mine. There are clips on each side that have very obvious holes that they go in
So the screws go back in the holes on the side to hold this cap on
now your
Trim molding goes on it just has clips that snap into place
To test to make sure we what we did worked correctly today
I'm going to set it on spin and pull out the switch
You'll see nothing happens because our lid switch is not pushed in. So now I'm going to close the lid
And our unit starts spinning I'm going to open it up and we'll see it come to an abrupt stop
So everything is now working our new lid switch is working and in place and our
Motor coupling is now spinning the agitator again
Since you made it this far
I'm going to assume that you learned something
Go ahead and subscribe to my channel and click the notifications bell
So you'll see when I post my next video if you found the video helpful
Give it a thumbs up post any questions you have in the comment section below and I'll respond as soon as possible
I hope you guys have a great day