Washing Machine Won't Spin or Drain Water | Replacing a Washing Machine Timer Switch #repair

TightWadDIY
899 followers
1.3K Video Views·Nov 12, 2023
Please SUBSCRIBE and hit that THUMBS UP button. It really helps grow our community.
CLICK THIS LINK to access my Amazon Storefront, view Merch, and find me on other socials! https://linktr.ee/tightwaddiy
*My description includes referral codes/links that allow me to earn points, credit, or money that can be redeemed for products and/or subscriptions. As an Amazon Associate, I earn from qualifying purchases. When you use my referral code/link, you are helping to support me and my recommendations! Thank you for your support!*
Music: The Right Direction by Shane Ivers - https://www.silvermansound.com
Welcome back guys, it's the Tightwad and today we're working on a Kenmore 70 series.
This is a direct dry washing machine and a lot of them function the same way, but as
you can see, we have a load of clothes in here, it is full of water.
It finished the regular agitation cycle and when it went to rinse, it completely stopped.
Now I have another video I'm going to link in the top right corner right now that shows
how to replace the lid switch, which is sometimes the issue, but today I think mine is something
different.
I'm going to close the lid to engage that lid switch and I'm going to pull this out
and you'll hear that there's some clicking noises coming from this dial right here.
One way I can tell it's not the lid switch is when I open the lid, it stops.
When I close the lid, it starts back.
Before you get started working on it, make sure that you unplug your washing machine
from the wall.
First thing we need to do is get these plastic pieces off and I've had mine off before so
they are a little bit easier, but if I just pull out on the top, it should slide right
off.
So I'm just grabbing behind this lip right here and pulling and then the bottom piece
kind of slides to the right.
Now we have screws to remove.
We have one screw here and one screw here.
And these are just Phillips head screws, but they do require one of the wider Phillips
head tips.
Now this piece just slides forward a little bit and it should lift up.
This is the backside of that dial that we're going to remove.
The first thing we're going to remove is this wiring harness right here.
On the bottom side of the timer, you can see there's a little tab right here that I'm going
to lift up and then I'm going to slide the wiring harness off.
Now that that's removed, I'm going to pull out this little black pin.
This is what holds the knob in place and it just pulls straight out.
I'm going to flip this over.
Now the knob should pull out.
Now that you have the knob off, you can pop these little clips and pull off this vanity
part.
Just carefully push them in and then this piece should come off as well.
The reason why you need to remove that vanity plate is there is one screw right here holding
the controls in place.
This was a 316th nut driver that I used to remove that little screw.
Now we're going to flip this back up.
Now I should be able to lift this tab and shift the whole thing to the left and then
it comes right out.
This tab is really the only thing holding it in and then these clips are the twist out
clips.
It's going to be a few days before I can get the replacement part, so I went ahead and
pulled the clothes out of the dryer and I need to get this water out of here.
It's been sitting here for three days and it's starting to smell a little bit swampy.
I picked up this drill operated pump that goes on the end of your drill and it works
as a siphon to pump all the water out of your tank.
So I'm going to drop this down into the washer and suck that water out.
It took about four and a half minutes to pump all of the water out of the washing machine.
This thing worked really well.
I'll make sure I put a link to it in the description for the video in case you want to pick one
up.
The new part finally came in.
So to insert it, I make sure that the pin goes into the hole, then I slide it to the
right so that everything locks into place.
We're going to flip this piece back down and insert the screw that holds it all together
in the front side.
When replacing this, you need to make sure that the one with the little ridge on it right
here goes into the ridge on the side of this.
With that in place, you can now put the knob back on and the two ridges go opposite of
the flat pieces you can see down inside here.
Don't forget to reinstall the wiring harness and make sure it's firmly clipped into place.
And then these white plastic clips go in the holes on the outside here.
Things should slide backwards.
And then you need to replace your screws on each side.
With all of that in place, I'm going to plug it back in and then we'll test out the function.
The moment of truth.
Select your cycle and we're filling.
For my first load, I'm going to run one of these washing machine cleaner tablets from
Active.
I'll make sure I put those linked in the description.
But we try to run these about once a month and it just cleans out the drum of your washing
machine.
It's just a tablet that you throw in and run a load.
I want to do this because this water has been sitting in here for a full week and I poured
bleach in it.
So I need to make sure all that old water is flushed out.
Thank you so much for making it to the end of the video.
It'd be awesome if you'd click that logo in the bottom left hand corner to subscribe to
my channel and maybe even check out one of my other videos shown on the right.
As always, I hope you guys have a great day.
