Biasing the MOSFET to obtain Linear Amplification || KTU || ECT 202 ANALOG CIRCUITS || Module 3
For full class
ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
#circuits #ktu #ece #electroniccircuit
Hi all, in the last class we discussed about voltage transfer characteristics in the case of MOSFET amplifiers.
We understood that the output voltage equation we derived is a non-linear relationship.
Only if we make it almost linear, we can make it work as a better amplifier.
The reason we use biasing is to make the non-linear almost linear.
For biasing, we select a DC voltage.
The reason we select the DC voltage is to fix the Q point in the saturation region.
In this region called AB, where the Q point is fixed, we select the DC voltage.
The coordinates of this Q point are BGS and VDS.
VDS is equal to VDD minus IDRD.
We solved this in the last class.
VDS is equal to VDD minus 1 by 2KRD into VGS minus VT the whole square.
This is the equation for the saturation region drain source voltage.
We substituted the value of ID in VDS is equal to VDD minus IDRD.
We solved this in the last class.
Those who have doubts can watch that session.
This Q point is called bias point, DC operating point or quiescent point.
In short, why do we use biasing?
We use biasing to obtain almost linear amplification from a MOSFET.
For biasing, we provide a DC supply to this circuit.
We provide the DC power supply to fix the Q point in the AB region.
Or we provide a DC voltage to this circuit.
Q point has two coordinates.
The coordinates are VDS and VGS.
To relate them, we use an equation.
VDS is equal to VDD minus 1 by 2KRD into VGS minus VT the whole square.
Q point is called bias point, DC operating point or quiescent point.
We have provided the biasing.
Now we have to amplify a signal.
We are giving that signal as an input.
The signal to be amplified, VGS, is a function of time is superimposed to the bias voltage VGS.
This VGS is superimposed to the bias voltage VGS.
We get an instantaneous voltage called small letter VGS.
The small VGS is equal to this small letter VGS.
This small VGS is a superimposed signal.
This VGS is the signal that is superimposed to the input signal and the bias voltage.
We can write VGS of time T is equal to the sum of the input signal and the bias voltage.
VGS of T is equal to VGS plus VGS of T.
The resulting VDS of T can be obtained for VGS of T into equation 1.
If the input signal is kept small, the corresponding signal at the output will be nearly proportional to with the constant of proportionality being the slope of almost linear segment of VTC around Q.
To understand this further, let us look at the VTC or Voltage Transfer Characteristics.
We have fixed the Q point here.
This is our Q point.
We are giving a small input signal to this.
We are giving a triangular waveform.
The Q point is fixed here in the segment AB.
The reference line is the line corresponding to the Q point.
The Q point grew correspondingly towards the negative maximum value.
The negative maximum value can be obtained in the segment AB correspondingly.
Again we say, the other way round.
The Q point shows negative value correspondingly to the segment AB, while the positive maximum value corresponds to the segment AB correspondingly.
The output that we get is this point, this point, this Q point is taken as a reference,
this point corresponding to this point, this line corresponding to this line, and this line corresponding to this line.
What we get is the amplified output of this signal.
See, we get the amplified output.
Here, we show the case of being a triangular wave or small amplitude.
Specifically, the amplitude is small enough to restrict the excursion of instantaneous operating point to a short,
almost linear segment of VTC around the bias Q point.
Q point is not a big value, it is a small value.
The shorter the segment, the greater the linearity achieved.
For example, if we take this segment as a small segment,
the greater linearity we get is the output without any change in the shape of the triangular wave.
We have taken the output as a short segment, so the output will be a triangular wave.
This is the essence of a linear amplification.
We have taken a linear point here.
This is the linear segment we have taken here.
We have fixed the Q point here.
This is the linear segment.
We get the output signal without any distortion.
Now, look at this point.
If the input signal is kept small, the corresponding signal at the output will be nearly proportional to
the constant of proportionality being the slope of almost linear segment of VTC.
The output is proportional to a constant.
Multiplying this by a constant is proportional.
What is that constant?
It is the slope of this.
We get this amplitude because the slope is this much.
If the slope is a little bigger, the amplitude will be a little more.
The output we get depends on the slope of the corresponding segment.
The slope of the Q point determines the voltage gain.
This is the basic concept of Q point.
In the next class, we will discuss the various types of biasing.
What is Q point?
Why do we use biasing?
Biasing is used to make the non-linear relationship almost linear segment.
Biasing is used to make the amplification purpose almost linear.
In the next class, we will study the different types of biasing.
I hope everyone understood the previous class.
See you in the next class.

