EC 462 Mixed Signal Circuit Design- SOURCE FOLLOWER
#ktu #s8ece #mscd
For full class:
https://www.youtube.com/playlist?list=PL2UV2EJdMQmim5UHGAuX6HtsAVCRB-2Ix
Hi all, today we are going to discuss about the circuit called as Swiss Follower
we have learnt about Common Gate and Common Swiss Configuration
now we are going to learn about Common Drain Configuration or Swiss Follower
in the case of BJT, this circuit is known as Emitter Follower
the counterpart of Emitter Follower is Swiss Follower
Swiss Follower uses MOSFET while Emitter Follower uses BJT
Common Drain Stage is another name for this circuit
the amplifier senses the input at the gate and produces the output at the source
with drain tied to VDD
the amplifier senses the input at the gate and produces the output at the source
with drain tied to VDD
this is the Swiss Follower circuit
the behavior of this circuit is similar to BJT's Emitter Follower
let's see the working
if the gate voltage of M1 is raised by a small amount delta V in
the gate voltage of M1 tends to increase thereby rising the source current
and hence the output voltage
thus Vout follows Vin
Vout follows Vin
this is the working of Swiss Follower
if the gate voltage of M1 is raised by a small amount delta V in
the gate voltage of M1 tends to increase thereby rising the source current
and hence the output voltage
if the gate voltage of M1 is raised by a small amount delta V in
the gate voltage of M1 tends to increase thereby rising the source current
thus Vout follows Vin
since the DC level of Vout is lower than Vin by Vg
we say the Follower can serve as a level shift circuit
this is the circuit diagram of Swiss Follower
the small signal equivalent is drawn here
this is the simplified form of the circuit
Vin is applied at the gate
gate is the gate of a MOSFET
gate switch terminal is open
there is a current switch between the drain and the switch
there is an output resistance
this is the transistor
input is applied at the gate
there is no other transistor
there is an RL resistor in the switch of the transistor
RL resistor is applied in the switch
and the output is taken
let us see the rest of the circuit
this is the simple form of the small signal equivalent
this is the transistor
RL resistor is applied in the switch
this is the simplified form of the circuit
this is the output voltage equation
output voltage is the current into resistance
current is the current going through the Gm into V1
current is in the same direction as the resistance
so there is no negative sign
current is the current going through the Gm into V1
resistance is the resistance going through the RL and RO
current is the current going through the Gm into V1 into RO parallel RL
this is called Vout
let us see what is Vin
Vin is the voltage
Vin is the total voltage going through the gate and the ground
Vin is split into two
Vin is equal to V1 plus Vout
Vin is equal to Vout divided by Vin
In this equation, instead of V1, we can substitute Vin minus Vout
we get Vout by Vin is equal to
Gm into RO parallel RL whole divided by 1 plus Gm into RO parallel RL
Gm into 1 by Gm plus RO plus RO parallel RL
cancel the Gm and write the equation in this form
Gm is taken as common in the denominator
cancel the Gm and write the equation in this form
The voltage gain is therefore positive and is less than unity
Let us see the voltage gain
Voltage gain is a positive value
numerator Gm into RO parallel RL
denominator 1 plus Gm into RO parallel RL
slightly greater than numerator
Gain is slightly less than unity
Voltage gain is therefore positive and less than unity
It is desirable to maximize RL and RO
As with emitter-followers, we can view the above result as
Voltage division between a resistance equal to 1 by Gm and another equal to RO parallel RL
Output voltage Vout is equal to Vin into RO parallel RL divided by 1 by Gm plus RO parallel RL
It will look like a voltage division equation
What is a voltage division equation?
Main voltage into resistance in another branch divided by total resistance
Isn't that how it is calculated?
Main voltage into resistance in that branch divided by total resistance
It looks like a voltage division equation
Voltage division between a resistance equal to 1 by Gm and another equal to RO parallel RL
It looks like a voltage division equation
What is the output resistance?
Input is grounded
Gate is grounded
Output is RO parallel RL plus M1 into resistance equal to 1 by Gm
Output resistance RO is equal to 1 by Gm parallel RO parallel RL
which is approximately equal to 1 by Gm parallel RL
This is how a source follower looks like
What is a source follower?
It is a common drain configuration
It looks like an emitter follower
Please note the brackets
Source follower or common drain configuration
If a small input changes, Vgs changes
Don't expect more source current
Don't expect delta V times increase
More source current will flow
Output voltage will also increase
So we can call it as output follows input
It is called voltage or source follower
What is a level shift circuit?
We have studied the small signal model
We have found the output voltage equation, input voltage equation and gain
We have written the output resistance equation
That's all for the source follower
In the next class, we will discuss the problems related to the source follower
Thank you

