Water can cause alot of damage in a short period of time. Fixing water leaks quickly and correctly can save you money in the long run. This sink was leaking from the hot water handle. The issue ended up being the o-ring on the valve stem. If you have a dripping faucet, the most likely culprit is the valve seat. I show you how to repair both in this video. I will include links to parts below.
Click here to see some of my favorite items on Amazon! www.amazon.com/shop/tightwaddiy
*My description includes referral codes/links that allow me to earn points or credit that can be redeemed for products and/or subscriptions. When you use my referral code/link, you are helping to support me and my recommendations! Thank you for your support!*
Welcome back guys, this is the Tightwad and today I'm at my parents house and I was washing
my face this morning and I noticed whenever I turned on the water that there was a leak
coming out of the back of the hot side and I'm going to show you today how to fix that.
You do not need a whole faucet, don't panic.
The fix for this is actually less than $4.
There are a few different places that your sink can leak on the top side and one of the
places is right here around the valve and that's what we're going to be looking at today
primarily, but it can leak on either the hot or the cold side.
Today I'm going to show you how to replace or repair the valve stem, which is just below
your handles, but if you have a slow drip from here, there's also something in here
called the valve seat that we'll discuss and the valve seat is the likely culprit if you're
having that slow drip.
One other thing that can cause a slow drip is if you have a buildup of calcium on the
bottom of your valve stem, so you can take some steel wool or CLR and get that nice and
clean.
It should just be polished back to be shiny like this one is.
So that's how you address the drippy sink and today we're going to get started by removing
this handle right here because this is leaking from the back side.
The first step in working on any sink or faucet is to turn off the water and today I'm working
on the hot side, but just in case someone comes and turns on the cold water, I suggest
you go and turn that off too.
And all water valves are righty tighty to close and lefty loosey to open.
And then you want to check on the top to make sure no water is coming out.
The next step for today is to put a stopper in or pull up your stopper to seal this off
so that any screws that you drop while you're working or parts don't end up going down your
drain.
Today we are working only on the hot side and to start you just have to twist this out.
This is a Delta faucet and most of them are made similarly.
Once you have the handle off, you need an Allen wrench or a hex key to take this piece
off.
It doesn't have to come all the way out.
All this is doing is pushing against a flat side on the valve stem that's under here and
keeping it from spinning continuously.
So you can actually leave it still in here.
If you do take it all the way off, you can just leave it sitting on top of the Allen
wrench or hex key here and that just prevents you from losing it.
Here's a screw in the top of your valve stem.
It's not essential to take off.
You can leave that seated right there, but we do have to take off this nut that holds
the valve stem in place.
So I just have an adjustable wrench here and I'll get it started with that and then I should
be able to get the rest off with my fingers.
It's now time to lift this piece out.
This is called the valve stem and you can sometimes grab it with your hand.
This one's a little bit loose or you can grab a pair of channel locks or pliers and grab
this top metal part of the stem and lift it up.
And this is what actually controls the water cutting on and off inside your sink.
And there's a few different parts to it.
These can be replaced.
The whole thing can be replaced.
If you go to the store, make sure you take it with you because there are a few different
models for even a Delta faucet, but make sure you get one for Delta.
But they also have O-rings on them.
So today what we're going to be doing is replacing this O-ring.
So I'm going to pull this off from the middle.
You can use a small screwdriver if you need to, but I'm going to pull off this old O-ring.
You can feel it's a little bit brittle and it's not quite rounded on the sides.
And we purchased a faucet repair kit.
We made sure it was for a Delta and it comes with a lot of different parts in here.
So I'm going to show you the parts that come with it.
It comes with several different size washers.
This is a universal kit for Delta.
All we need is the one that's the same size as the one that we took off.
And then we also need this piece, which is called the seat, and then this piece, which
is the spring.
To put the new O-ring on, you just get it started around the bottom side here and then
just slowly roll it into the groove that is right where it came off of.
And you can set this to the side for now.
There's a good chance that it's full of water, so you can take a paper towel and dip down
in there to soak the water out so you can see what you're doing.
And I'm doing it really today so that I can show you what I'm doing.
With the water out, you can now see that the seat is right over here on this side.
It has the spring in the bottom and then the rubber seat right above it.
And you can just stick your screwdriver in there and pull it out.
Notice the orientation of the spring when you pull it out.
There is a taper that goes up towards the handle of the faucet.
So this is the seat and the spring that I removed, and you'll see that there is a taper
going towards the rubber seat.
So the bigger part or the wider part of the spring is going to go in first when we put
it back in.
And also the seat has a rounded over part at the top and a sharper edge on the bottom
piece.
Another product you're going to need is waterproof grease or valve grease.
And I'll put a link to this in the description and in the pinned comment where you can order
some from Amazon if needed.
And I'll also do the same with all the other materials that I'm using today.
But just squirt a little bit on your finger and then rub it around the O-ring.
This is going to keep the O-ring from grabbing onto anything when we install it so that it'll
seat itself properly.
So I get it on the O-ring here and the next thing I need to do is get some on this valve
seat as well.
So I'll rub some on the top of that because that's going to go down against the valve
stem.
Now I have my spring and I have the taper going up towards the seat.
And you can put it back on your screwdriver and slide it down into the hole and then just
let all the spring and the seat slide down into place.
I'd really appreciate it if you'd take time to hit that subscribe button and then turn
on notifications for my channel as well.
Alright, now I have it seated properly.
You'll know it's seated properly when you can push on it and you can feel it spring
up and down.
Now I'm going to put the valve stem in.
But before I do that, I'm going to check the bottom and make sure it's nice and clean.
And I'm putting some more waterproof grease or valve grease on the bottom.
Notice where the notches are in the sides of your valve stem and they go right here
in the notches on the faucet itself.
And then you want to push that into place.
And you should be able to feel it move up and down a little bit if you push on it.
The next thing we need to do is put the nut back on.
And the nut had the bevel side up so the part that the tool goes on was down on this and
the bevel side was up.
And I'm going to start screwing that on, righty tighty, lefty loosey.
Sometimes it's easiest to get these metal fittings going correctly if you spin them
counter-clockwise first until you feel the threads lock into place.
And then you can spin them back clockwise to tighten them down.
That keeps you from cross-threading them.
And I do have some of that waterproof grease on my hands so it's making it a little bit
difficult to get that screwed in.
So instead I'm going to grab my adjustable wrench and tighten it the rest of the way down.
You don't have to tighten that down super tight, just get it nice and snug.
And now it is time to replace the handle.
The hole where the handle screws in on here goes out and you also have the seat here that's
going to go against the flat part of this post.
So I'm going to push that down on there.
Make sure it's down nice and snug.
And then I'm going to tighten up your Allen key.
And again, you don't need to over-tighten that, just make sure it's nice and snug.
And then we can screw back on the handle.
And everything on here is threaded righty-tighty, lefty-loosey.
Before we turn on our water to test, I'm going to dry up all the water that was here from
the previously defective O-ring.
And now I'm going to make sure my drain is open.
I'm going to cut on both water valves, turning them to the left.
And with the water all dried up and the valve turned back on, you can open this and see
that we have no more leak coming down the back.
If for some reason yours is still leaking, you can replace the whole valve stem by purchasing
a new one from a hardware store or a big box store.
And on a Delta faucet, they are the same for the hot and the cold, so you don't need to
worry about whether it says hot or cold.
It is the exact same valve stem, it just goes in the opposite direction.
So just replace the whole valve stem, still using the waterproof grease on all the rubber
parts and you should be good to go.
If you have any questions, make sure you post them in the comment section below and
I'll be sure to reply.
Give this video a thumbs up if it helped you out today.
Click any of the videos shown on the screen right now and they'll open right up on your
device.
Don't forget to check the description for the video or the pinned comment for any follow-up
information and also to get links to all the products used today.
And I hope you guys have a great day.