EASY: Kitchen Sink Leak Repair

TightWadDIY
899 followers
3 Video Views·Jul 8, 2020
Water leaks can prove to be VERY costly. Most leaks are much easier to fix than you might think. In this video, I show how to replace a sink drain seal with only two tools, a screw driver and channel locks.
If your leak is in the bathroom, this video shows how I fixed a link in mine:
https://youtu.be/Iqv_Vl4hQ7U
Use the Amazon Affiliate inks below to order the tools and supplies seen in this video.
P Trap - https://amzn.to/2DdKrSA
Sink Gasket Set - https://amzn.to/2ACPYRM
Plumbers Putty - https://amzn.to/39cbPwc
Channel Locks - https://amzn.to/2VQRFm7
Screw Driver Set - https://amzn.to/38ByYYB
Welcome back guys, it's the Tightwad and today I'm going to show you how to locate and repair
leaks and show you some potential problem areas under your kitchen sink.
I wasn't intending to actually make any repairs today, we just ordered a new faucet.
So I was getting prepared to install the new faucet, which is mainly dealing in this back
area over here, but then I noticed that I had some water up here around the sink
seal or the drain on the left side of my sink and some wetness and then down here on the bottom.
The telltale sign of long-term water damage, so hopefully my damage is just limited to right here
and it's a very very slow leak. I feel something here but I haven't seen a drip since I've had
this open, but I'm going to show you how to remove all of this and show you what parts you need to
consider replacing whenever this happens. The first step when doing any kind of work on your
sink is to cut off the water lines, so you should have a cold and a hot cut-off valve.
This is a different cut-off valve that's taking water from here to the dishwasher, which is right
next door, so I don't really need to worry about that one today. I'll just leave it on, but your
water line is always righty-tighty, lefty-loosey, so right is to close, left is to open, just like
a spigot outside or any other connection. And now we need to start disassembling the P-trap and the
drain coming from the sink, and all of these are easy to do. They just have hand, they're just
hand tightened so you can easily remove them by just spinning them with your fingers. But before
we remove this, there is going to be water trapped in here, that's the whole purpose of this is to
prevent vapor from your drainage system from getting up to your drain, so it traps water in
here to create a barrier for you. So this is definitely going to be full of water and probably
some nasty stuff because it's coming out of the sink and it catches a lot of debris and keeps it
from draining down into your drain lines. So before I start removing anything, I've got this large
Tupperware that I'm going to stick under here. I was planning to use my bucket, but it's a little
bit too big for this application. And now I can just start removing the parts, so I'm going to put
the camera on the tripod so I can use both hands. And again, like I said, these just loosen by hand,
so I'm going to go ahead and loosen that one and this one. You can see the water start to leak out
here, which is expected, and it drops off. I should have been holding under it, but I'll show you that
down in there is actually really clean on this one. We don't pour any type of grease or anything
down our drains, but the bucket is very helpful for this, so I can just drop all my parts down
inside there. So I do not need to remove this piece, but it's easy to remove as well just by
twisting it. I'm going to leave this piece in place because I'm just needing to get up to the
area right here. So the next thing I'm going to do is disconnect here, and I do have my bucket for
this side. I need to get a flathead screwdriver to loosen this. All right, with that hose clamp
loosened, I can slide this off. Be careful, there's going to be water in it. Most likely not, but there
could be. And now I'm going to loosen the nut here, and I may be able to slide it off. Yeah,
I can slide it off without having to do this over here, and I'm going to drop this down in the bucket.
So with that removed, I can now get to the culprit of my leak up here at the top. You need to loosen
the metal nut at the top, and you'll see here that I'm using some channel locks to do this.
So this piece just came right off, and I'm going to drop it in my bucket,
and now I'm going to remove this. And with that removed, the whole thing will slide out.
You can see that the plumber's putty around the rim of this was all cracked up, which was probably
causing our leak, so I'm going to get that cleaned off. And then this piece here, and the washer was
kind of not seated properly, so I'm going to buy a new one of these washers and some plumber putty
and get this all put back together. These are the two things that I had to purchase at the
hardware store. I had to get some more plumber's putty because mine was dried up. This will go
under the top rim, which is right here, under here, to seal it. And then I also purchased this,
which are the sink strainer washers. There are two. One is the black rubber washer I showed you
before, and then the other one is a friction washer that goes just below that and against the rim
of this piece. You can see it right here. I can fold up the edges of it. So I'll remove that and
get a nice, clean seal all the way around. And we're going to start here on the top side.
Take a paper towel and get this nice and clean. If there's any kind of gunk in there, make sure
you scrape it off. Get it nice and clean. And the same for the underside lip of your drain,
because we're going to be putting the plumber's putty, running a bead of plumber's putty along
this, and then pushing it down to get a nice, clean seal right here. This is what the plumber's
putty looks like, and I'm going to get some out here. It's a little bit thicker, harder to work
with than Play-Doh. And I'm going to roll it in a snake, just like we always do when playing with
Play-Doh. And you want one long bead of this. All right, so with the end where it joins together,
you want to punch it down so there's no seam in it. And now I'm going to push this down into place.
So I'm going to get it centered directly over and press down, even pressure all around.
And when we tighten the nut on the bottom, it's going to tighten it down a little bit more,
and we can trim off any of this extra. If you don't get any squeeze out, you didn't use enough.
Now we're on the bottom side, and you can see we've got a good deal of squeeze out here,
which is fine. I'm just going to cut most of that off. I'm going to leave a little bit,
and then we're going to fit the washer around the bottom piece
and slide it up on here. I used a SOS type scrub pad to clean that off, and I'm going to put the
new friction washer on there, and then the new rubber washer, and get them nice and even around
here. And then I'm going to push them into place, and then we'll have to screw the nut on from the
bottom to secure it. But first, remember I said I'm going to remove this putty that leaked out
of the bottom here. I probably actually needed about half as much as I used, but I'm going to
have too much than too little, since we can just remove it. So now I have my washer stacked here.
I'm going to slide that up into place, and then I'm going to take this nut and screw it on.
Before I tighten it down, I'll make sure the washers are spaced evenly around it,
and then I'll take my channel locks and tighten that up.
I am going to link all of the parts that I'm using in this video in the description,
as well as in the pinned comment, so that you can easily order your own. They're Amazon affiliate
links. It'd also be awesome if, while I'm tightening this up, you could take the time to
subscribe and then ring that notifications bell, so you can see each time that I post a new video
on my channel. It really helps me out. And I'll see you next time.
All right, that is nice and snug now. It was a little bit loose previously, but it's nice and
snug. And now we can start reassembling all the different parts of our drain. And that starts with
this piece, which was coming out of the bottom right here. So I'm going to go ahead and screw
this one on. And that one doesn't go on too far, but I am going to make sure it's good and snug.
It doesn't have to be super tight. Just needs to make sure it doesn't come loose.
The next piece was this one. So I need to get it started here, slide it in, and then push it up on
this side, and then tighten down the nut. I'm not going to tighten anything down a lot. I'm just
going to make sure they're all grabbing, because I'm going to make sure everything's lined up
correctly before tightening anything down. So I'm putting on this nut in the middle,
and now I have to put my P-trap back on. The next part is the P-trap, and it slides up on this side,
and I can go ahead and get that one started. And then the bottom connects right in here,
so I can get that one started as well. And these nuts will kind of guide them into place as you
tighten them. And now that everything's in place, I can tighten them down. And you're just looking
for snug here. You're not really cinching down hard. You want the next person to be able to
remove them fairly easily. You can reconnect this hose here, push it on as far as it'll go,
and then tighten it down. While I'm under here, I'm going to go ahead and turn on the water,
even though I'm not quite finished. So I've turned on both of the water valves,
and then we're going to go back to the top and remove the excess putty from the top side.
And I'm going to just use my fingers to remove most of it, and then I can get a knife or
something down in there to remove the remainder. For removing the excess putty, a knife, kitchen
knife, table knife, works pretty well. And you just want to scrape all that extra out of there,
otherwise it's just going to get slimy and gross. And for our final step, we're going to turn on the
water. I'm just going to clean off any of the residue that's here, and we're going to look
underneath to make sure there are no leaks anywhere. I do recommend you come back in about
a week to double check to make sure there's still not a leak anywhere. All the pipes should be
completely dry. If you want to, if you're nervous about it, you can leave your empty catch basin
down here. I still have some water in it and some trash I need to get rid of, but I'll put this back
in here completely dry so that I'll be able to see if there is even a single drip of water.
But it looks like our project is finished. Hope you guys found this video helpful. If you did,
give it a thumbs up and subscribe to my channel. If you haven't already done so, click that
notifications bell so that you'll be notified each time I post a new video. Click any of the
videos showing on your screen right now and they'll open right up your device. And leave any
questions you might have in the comment section below and I promise I'll get back to you. I hope
you guys have a great day.
