Every year my family does a hand made gift swap. This year, my wife's contribution was a blanket ladder. She always asks me to make two so she can keep one and gift the other. I was a little behind getting hers to keep made this year!
This video shows how to make the ladder step-by-step (pun intended).
You will need to purchase: 3 - 3/4" x 2 1/2" x 96" (commonly called a 1x3x8) Other supplies you may already have: Wood Glue - I prefer Titebond 2 or 3 1 1/4" Kreg Screws Wood Stain
Cut List: 2 - 72" boards 6 - 17" boards You can usually pay a big box store to cut these lengths for you but in my experience they have less attention to detail than you will so I recommend cutting them yourself.
Here are some Amazon Affiliate links to other products I used or recommend for this project.
*My description and pinned comment may include referral codes/links that allow me to earn points or credit that can be redeemed for products and/or subscriptions. When you use my referral code/link, you are helping to support me and my recommendations! Thank you for your support!*
Welcome back guys, it's the Tightwater and I have a special project for you today.
My family does a handmade Christmas gift swap every year at Christmas, and this year my
wife made a blanket ladder that looks like this.
And every year she wants me to make two because she wants to give one away and keep one for
herself because her idea is always something that she wants.
So today I'm going to be showing you the step-by-step process, including the cut list and all the
measurements for building that blanket ladder.
I'm going to get started today with some one by three by eights.
I got the higher grade of wood from my local big box store.
I typically shop at Home Depot because that's what's in my area.
And today I'm going to be using the PPE.
I'm going to be using my 3M headphones.
These are super comfortable.
If you've never tried them, I highly recommend them.
They're very affordable, great battery life and super comfortable.
Not sponsored by them.
I've been using them for probably three or four years now and they're awesome.
And then my favorite goggles are these Uvex ones.
I found them on Amazon.
Again, I paid full price, not sponsored.
But I like these much better than your typical safety glasses because they have this seal
around them and it's a nice comfortable seal, unlike the ones that are made by DeWalt.
And then I have this stealth light mask that Trend sent me.
They did send me this for free.
So to get started today, the first thing that I always recommend when working with new lumber
that I'm going to assemble or that I like to do is give it a good sanding at the beginning
to take off any of the rough stuff.
I am going to sand it again later, but I just like to get the rough stuff off first.
We're going to start today by getting these cut down to the right lengths and then we
will get them on the round over.
Using a round over bit isn't a necessary step.
It's just giving those edges the nice round, smooth feel.
You can do the same thing with a sander if you have a little bit of patience and a little
more time.
The first thing I want to point out is that always check your boards.
If you have extra board, make sure that you're removing these splits like is in the end
of this board.
And hopefully only one end of your boards is split.
This other end looks pretty good on this board, but I'm still going to remove this factory
end before I start doing any measuring.
Not only does it have a rougher cut with some ink in it, but these are not always cut square.
So I like to start with a nice clean square edge before I start doing any measurements
or cuts on my board.
When cutting two boards that need to be the exact same length and that are longer than
my miter station so I can't use a stop, I like to do a stack cut.
So I'm going to measure out 72 inches on this top board and now I'm going to butt the two
ends of my board together here and clamp them so that they are perfectly even with each
other.
And then when I cut, I'll get a nice clean cut that ensures the exact same length on
both boards.
So I have the ends right here even with each other.
I have a clamp on it and I can hang it off the right end of my miter saw station here.
And now when I make my cut, it's going to go through both boards and they're going to
be the exact same length.
I'm now ready to cut the rungs for the ladder and they're going to be 17 inches long or
wide, however you look at it.
So I'm moving the stop on my saw so that I can cut them each in succession repeatedly
without having to measure each one.
I had a fairly big knot in this board in the middle and since I knew I had a little bit
of extra length, I went ahead and cut that out.
And here are the six rungs all cut to the exact same length.
Here I'm running all of the boards through my router table with a quarter inch roundover
bit on there to just smooth out those harsh edges.
The next step in the project is to take your two long boards and cut your angles.
So the reason for the angles is so that it doesn't stand straight up on the floor and
doesn't sit on a point.
You want to create an angle that's going to allow it to lean comfortably against the wall.
And what I've found works best is a half inch measuring up on one side here, one half inch.
So I have my square here and I'm going to measure up to one half inch.
And if you have a miter saw that you can adjust the angle on, this is actually a 10 degree
cut.
So approximately a 10 degree cut.
So we're going to get the bottom of both of these cut off to that, from this corner to
the half inch mark.
So starting at this corner and going straight to the half inch mark here, and that'll give
us the nice taper for the bottom of the legs.
As you can see, I adjusted my miter saw blade to 10 degrees.
This doesn't have to be exact, but as close as you can get would be great.
And now I'm going to go ahead and cut them off.
I did clamp the other end of the board together again, so I can cut them both at the exact
same time and have them the exact same length.
With the other ends cut, I'm going to make sure that I'm working with the back of the
ladder.
And that means that my lower angle is coming in this direction.
Now I'm going to measure over three quarter inches from the side here and make a mark.
And then on the long side here on the back, I'm going to measure four and a quarter inches
and make a mark.
So one, two, three, four and a quarter.
Not starting at a reference point zero, so it's always good to measure and then measure
twice, one, two, three, four and a quarter.
So now I can connect these two lines here and then I can move over to the miter saw
and cut them.
So now that I have that marked, I can get a reference point on the miter saw.
This angle is hard to cut on a miter saw because it's not exactly an angle that your miter
saw is made to cut, but I'll show you some tricks to make it happen.
If I brought my piece over to the miter saw, there's no way to adjust the blade to make
that cut.
So we need a piece that we can cut the angle on that the piece we're going to be using
can rest against so that we can cut it safely.
So we cut a 10 degree angle on the bottom.
That means we need a 10 degree angle on the top.
So I'm going to move the miter saw over to 10 degrees here and I'm going to make a 10
degree cut.
With that 10 degree cut, I'll be able to rest the piece against it here, get it lined up
on my cut line and I can make the 10 degree cut on the back side a lot easier.
So now I need to clamp this in place and then I'll be good to rest this piece against it
and against the fence on that corner and make my cut.
So we were able to safely make this cut because this piece is against the fence and then this
piece is braced against it.
So it's nice and safe to make this cut on the miter saw.
Please don't try to freehand cuts like this.
This piece will move and flip and turn and can cause major damage.
And here you can see the reason for these tapers.
I have this leaning at a comfortable angle and it sits flush against the wall and against
the floor.
The next step is to add the pocket holes using our Kreg Jig to the end of each of the rungs.
Now you could drill in straight from the side of the ladder into the tips of this.
It's just not as easy and it's not going to be as clean.
So I do love this Kreg Jig K5 system.
I purchased it.
It is not a sponsored link.
I like it for several reasons.
I love this adjustable stop on the back.
I love the nice beefy handle on the front.
The other one had kind of a cheesy little weak feeling handle.
I added this to the dust collection.
So it's made for a shop vac to plug in here, but a regular shop vac hose doesn't fit.
So I purchased this from Home Depot.
It's a rigid brand adapter and the smallest size here fit fine.
You need to make sure you always set your board thickness here.
So I have this set to 5 8ths, even though these boards were originally 3 quarters, I've
sanded them down a little bit.
And I always like to go a little bit shallower on the board size than it actually is.
A little bit thinner because I found that the Kreg Jig holes sometimes go through.
The next thing you need to do is figure out which size screws you're using.
And today we're using one and a quarter inch pocket hole screws.
So I'm going to slide in my bit here and it's going to go into that hole on my little podium.
It looks like the Olympic podium.
And then I can take my Allen key here.
I'm going to loosen the collar and stick it back down in there and make sure the collar
is sitting flush and tighten that collar back down.
That's going to ensure that we're getting the exact depth that we need.
I can pull this out and put this off to the side.
This will now go in a drill.
I actually like to use an impact drill for this.
I think it does a lot better and you don't have to use an impact drill.
But one time I was drilling through some treated pine doing pocket holes and the impact drill
did a much better job.
So I'm going to clamp my first one in and I'm going to be putting two holes in each
one.
So I get it lined up nice and even here, slide this up to probably an eighth of an inch away
from it.
And then the clamp on the front gives it the rest of that clamping power that you need.
And then I'm just going to set up my dust collection and I'll get started with the crank
holes.
The next step is measuring where your rungs are going to go.
And we're going to measure and put a line where the bottom of each rung will go.
So this is the bottom of our ladder down here.
And I put my two boards together here, so I only have to measure once and I can mark
both boards.
So what I'm going to do is start here on the longer edge of the bottom.
I'm going to measure up eight inches.
So that's going to be eight inches.
And then it's going to be every 11 inches after that.
So we're going to go eight, then 19, then 30, 41, 52, and 63.
Again this is a time when it's very handy to have one of these squares because now I
can put it against my board here and I can mark the center of this piece and this piece
And I can come down and do the same thing all the way down, marking the center of each
one because that's where the bottom of the rung is going to go when we start attaching
them.
What I'm doing now is clamping a 2x4 down to the table and I'll show you why once I
get it clamped.
So I wanted you to see that you could clamp a 2x4 to anything that's flat and you could
use it to brace against.
So the next step here is going to be putting these braces in.
So I can go ahead and kind of show you the basic layout.
And what this 2x4 is going to allow me to do is to push in from this side or from this
side when I'm drilling in these pieces, it's going to allow me to push against it to get
a nice tight fit.
Now I need to find something to set these cross pieces on to bring them up to the portion
I want.
And I'm going to be mounting mine right in the center and I'm not doing any kind of angle
and I'm also not mounting them this way because I don't want someone to try to climb on this
ladder because it's purely a decorative ladder.
So I just want mine mounted halfway on each side here.
So I have a three quarter inch board and a quarter inch board and I'm almost right in
the center and I'm happy with that.
So this is what I'm going to use for my spacing.
So I'll be able to use this piece all the way down.
I'm almost ready to start driving my screws here, but I want to review a little bit of
my setup.
I have this to press against.
So I'm going to be working from this side of the table, pushing against it.
So as I'm pushing the board, this is holding it on the backside from sliding away.
I do have this square.
If you don't have some of these things, it's fine, but I will put links to them, Amazon
affiliate links in the description and in the pinned comment.
So you can see some of the things that I'm using in this video and our marks were marked
to the bottom of the board.
So when we measured up eight inches, that was to the bottom of where this board goes.
The last thing I'm going to do is add a little bit of glue to the end of my board and then
I'm going to be screwing it in using my drill and I have my screws attached with a magnet
here so I don't have to reach back to the pile of screws every time I need another one.
Make sure your drill is in the low speed section.
Anytime you're drilling pocket hole screws into pine, make sure it's in forward and you
can see it got our screw in there nice and cleanly.
After driving that first screw, I noticed that I'm driving just above the center of
this board.
So I'm actually going to take this two by four and turn it up on its side so I have
a little bit better surface to push against.
Now I'm ready to go down.
Now when I push against it, you see there's no give in the other side.
Put that side in, we're going to move all the way down.
So we're going to do this whole side before we start working on the other side.
So I'm going to get everything lined up here.
That black square was a little bit too long to fit between my two rungs here.
So I had to switch to another size, put a little glue on the end of my board, get it
lined up here with my square, push it firmly against the other side, and then repeat the
process all the way down the ladder.
With that side finished, I can start working on the other side now.
So now we're just repeating the same process for the other side.
And this should be easier.
It should just be lining up the holes and driving the screws.
The difference is we're going to put glue on all of the pieces before we get started.
The key here is trying not to let these other pieces touch until it's time to do so because
glue causes your stain not to soak in properly.
I do have a little bit of glue squeeze out going on here.
So I'm going to show you a little trick.
This is just a regular drinking straw, and I'm going to press it into the corner and
slide it along and it scoops out the glue.
So now I can snip that off with a pair of scissors on the end, just snip off the very
tip of it, and you can go back for seconds.
And that'll get all that excess glue there and prevent it from drying on the piece.
It's now time for the final step, which is staining.
With stain, you should stir, not shake.
So I just kind of swirl it around, more of a stirring motion.
This is a stain that I've custom mixed using both the Golden Oak stain from Minwax and
the Provincial.
So it's a little bit lighter than the Provincial and obviously darker than the Golden Oak.
And to stain, I like to use old t-shirts.
Just a plain old undershirt like you would wear under a business shirt, because I always
have plenty of them.
So I just cut them up in little sections and then I rub it on, making sure to get down
in the cracks.
And I'll go over the whole top side here, and I'll make sure I get the backside as well.
You'll see me switching back and forth here because I don't want one side to dry, which
will create splotches.
And I'll go back and forth as I do the rungs.
And here's the final product.
You can see it sits nice and flush there, my wife has hung a blanket on it, and then
it sits nicely here.
One tip, we do have a robot vacuum cleaner and she tends to bump into this and knock
it over sometimes, so you can put some furniture anti-skid pads there and up here and it'll
make it where the vacuum cleaner won't knock it over when it's being bumped.
I hope you guys found this video helpful.
If you did, give it a thumbs up and subscribe to my channel.
Make sure you hit that notifications bell so you hear the next time I post a video.
I do mostly DIY style videos, but I also do some furniture building as well.
If you have any questions, leave them in the comments section below and I'll be sure to
answer.
Click any of the videos shown on the screen right now and they'll open right up on your
device.
And as always, I hope you guys have a great day.