Easy DIY Storage Cart | ONLY 1 Sheet of Plywood and 4 Power Tools

DO IT YOURSELF - DIY
308 followers
11 Video Views·Nov 2, 2022
This week at Project Build Stuff we are building a super simple DIY Storage Cart. If you're like me you always have stuff in the way, this DIY Storage Cart is perfect to help you get clean and organized!
What's up world? This is Brad from Project Build Stuff and today we're building this
awesome rolling storage cart using only four tools and one sheet of plywood.
If you're anything like me your garage is probably always a mess. Every time I go to do a project
there's tons of things in my way from tools to paint cans to sporting equipment. If it can get
in my way it does. So today we're going to be building an awesome DIY storage solution that'll
help organize your shop and mine and keep it looking great. And even better it only takes
four tools to build so anyone can do it. Enough of me talking let's get to work.
Whenever I'm going to be breaking down large sheets of plywood I always pull out my folding
work table and throw a sheet of rigid foam insulation on top. This is a great solution
because you can cut into it all you want you don't have to worry about messing up your workbench.
Breaking down large sheets of plywood like this can be really overwhelming at first but I want
to tell you it's not that hard. All you need is a couple of tools. Namely a trusty circular saw,
a couple of squeeze clamps, and a nice straight board. We're going to be using this board as the
guide for our saw to cut on all of our cut lines. To get those cut lines be sure to check down in
the description where I have full plans for this project that have all the cut lists and diagrams
you need to cut your plywood down to the perfect size. Before we start doing any cutting we need to
make sure we check one thing on our saw and that's the distance between our blade and the edge of our
base plate. In my case that's about an inch and three quarters but on every saw it's going to be
slightly different so make sure you measure it on yours and remember that number. So I need to
remember an inch and three quarters because we're going to need that when we're setting up our cuts.
So for this first cut I want to cut at 60 so I'm going to mark at 61 and three quarters.
Then just place your guide board on your mark and clamp it down. As you're cutting make sure
you're keeping that base plate tight against the board to get a nice straight cut. Just remember
the steps measure, mark, clamp, and cut. With our plywood fully broken down we're left with five
pieces to work with. You have your top and bottom, your center divider, and your two sides.
We could move on to the assembly right now if we wanted to but I think I want to add a little
visual intrigue to this since I'm going to be seeing it for years to come. So on the base as
well as the two sides we're going to add some roundovers which number one removes that sharp
pointy edge that I just know I'll hit myself on and will make it look a little nicer. The cup I'm
using to mark this curve is about four inches but any round object will do just fine. When it comes
to the jigsaw it can be a little scary but just try to stick as close to that line as possible
and we'll clean up any imperfections with the sandpaper. Make sure to round over all four
corners of the base as well as the top two corners of the side pieces. It's time to start tackling
the assembly and this can definitely be the most stressful part of any build but I've found having
the right tools makes it go so much smoother. We're going to be using the M12 Milwaukee Pin
Nailer for a lot of this assembly which is great because it helps everything go together super
quickly. I love this tool. We're also going to be gluing together all of the joints using a little
bit of wood glue and then to keep everything nice and rigid and strong we're going to be driving in
a couple of screws. This will make sure it lasts for years to come. I'll be sure to leave a link
down in the description for all the tools I'm using on this project so you can check it out
and see if there's anything you need to add to your arsenal. We're going to start by joining the
top to the two sides. Make sure you put a healthy amount of glue on here because that's what's going
to be doing most of the holding in these joints. We're going to hold it in place with a couple of
pin nails while the glue dries. These 90 degree clamps are great for this type of project because
they hold everything in place until you can get some nails in. The center divider is going to go
in just the same just make sure it's perfectly centered between your two sides. When putting
the base on I found it's easiest to flip the whole project upside down on its head and nail
it in from the bottom. The main body here is fully assembled and it's really looking good
but I have to say I'm so happy with this Milwaukee M12 pin nailer. It is working out great for this
project. It's nice and light and small so it can fit in all the nooks and crannies of this project
and it drives the nails the perfect depth so I have a nice smooth surface and no cleanup is
necessary. Big shout out to Home Depot for sponsoring this video and providing this M12
pin nailer. It has been great. If you are interested in picking up any of the Milwaukee M12 tools
be sure to check the link down in the description for the full Home Depot lineup that they have.
They're great tools. Go get one for yourself. We're going to finish off the main assembly by
throwing a couple screws into each one of these joints and that just ensures that everything
stays nice and rigid. With everything fully assembled the next step is to figure out how
we're going to hold up our milk crates so we have lots of storage. I ripped down a couple of pieces
of plywood on my table saw that work perfect for this but if you're someone who doesn't have a
table saw don't worry I have an alternate for you that'll work just fine. You can also pick up
one by two pieces of lumber from your local Home Depot that will also work. We're going to nail
these on the inside here to support our milk crates. Before we get those bottom supports in
place we're going to put a couple of strips of wood down the back edge. This will work as blocking
to stop our crates from sliding through when we insert them. To keep our bottom supports level
and even I cut a couple of spacer blocks at 13 and a quarter. This takes all the guesswork and
measuring out of it and makes this part of the project go so much quicker. I am so happy with
how this rolling storage cart came out. It looks so nice in my shop rolls away when I don't need it
but most importantly it's helping me stay organized which I needed bad. All this junk that would
normally be all over my workspace is instead tucked away and easily accessible in all of these
milk crates. It is so nice. I hope some of you guys go to tackle this project on your own. It's a great
DIY friendly project that only uses a couple tools. If you're going to tackle it on your own
be sure to check the link out down in the description for full build plans to this project
and many more over on my website projectbuildstuff.com and if you do make one for yourself I'd love to see
your take on it. Be sure to send me some pictures over on instagram at projectbuildstuff. Hopefully
you enjoyed watching this project as much as I loved building it and until next time it's your
turn. Go build stuff!
