How To Build A Modern Desk For Your Home Office

DIY Creators
91 followers
23 Video Views·Dec 10, 2022
Hey what's up guys today I'm going to show you how to build this desk for your home office
with color changing LEDs right here on DIY Creators. Let's do it! To begin this project
I'm going to start with the top which is the easiest part to start with in my case
so I'm going to cut it down for the right size to fit my specific needs and since I'm cutting
against the grain I'm using masking tape to reduce the amount of tear out and to give it a thicker
look I'm using one by two trim to cover the edge and now I can mark the locations to put
the pocket hole screws. Apply wood glue and then the trim. Remove the excess glue and then install
the screws. As far as the bookshelf leg I'm using a section of wood that's slightly bigger than the
actual leg itself in width. Now measure off the first line to create the second line which would
give me that angle I'm looking for and I find it much easier to use a circular saw to cut this
versus trying to figure out how to use the table saw to cut this line. This leg will determine the
height of the desk in addition to the top and I missed my mark by about an eighth of an inch.
And because this leg is getting painted I'm using a different kind of wood which
you'll never be able to tell. No I did not purposely go buy different wood I'm using
what I have. I'm using my angle finder to carry out the same angle onto the next piece of wood.
Set the table saw to the same angle and then trim off the edges.
And now cut out the shelves and the top and bottom but cut those a bit bigger than they need to be
because we're going to fine tune those on the table saw. And if all the cuts went well it should
fit right in. And now apply wood glue, spread that out, nail that together and then do the same thing
for the other side. And now install the top, the bottom and you can also install the shelves even
though I didn't install those in this initial process. I saved those for later which I wish I
had done at the time because then I had to do touch-up work. And now to make the cabinet with
the drawers. Again this piece is fully customizable for your need but I will have all the dimensions
down in the description. And while I'm at it I might as well cut the drawers as well and I'm
going to have one large, one medium and one small so all three of them will be a different size.
I also cut a few dividers to put between the drawers. To secure this cabinet I'm using
pocket holes in selective location only at the bottom and only at the top. Now secure the bottom
to the side panel and do the same thing for the other side. Now because I didn't want to see any
pocket hole screws in this section I'm using the nail gun to nail the back onto the sides.
Now secure the top. Install the 1x2 trim at the top and also at the bottom. And with the
router bit I notched out a section for the drawer bottom support. And now I can assemble majority of
the drawer, insert the bottom, square it up, apply glue and nail only the three sides together.
I would add the other piece later on in the video. I'm installing the hardware now because I want to
make sure everything lines up and I can fix any issue I may have. I'm temporarily adding the face
to the drawer so that I can get an accurate layout for the trim that go around the door.
This desk is going in the same room with the murphy bed I previously built so
it was really important for me to keep the look consistent and the drawers looking the same.
Installing edge band can make your life a lot easier especially when you're using layer ply
and when your partner is not paying attention sneak the iron use it put it back like nothing
ever happened. So to patch all these holes I just created I'm using this plastic wood which is
awesome it's pretty simple just apply it it dries fast you can sand it stain it or paint it. And now
for the prep work. Now once you sand this is the kind of look that I'm going for this is what we
want the edge band to look like. I also applied the plastic wood in the crack of the tabletop
which actually just closed that gap and I said it was stainable so it blends right in. I'm sure I
lost track of time but I must have spent at least three to four hours straight sanding and I took a
wet rag to wipe off all the loose sand that may be hanging around so I can apply this coat of stain.
So I applied the stain to the top and it went on a bit darker than I anticipated.
I kind of panicked a little bit and wiped it off just to make sure that I was going to get
the right color and I actually ended up being happy with it so I just continued.
I carried the stain over to the door trim and also the drawer bottoms.
So I originally started out by spraying these cabinets. I got extremely frustrated with
the whole painting process and that didn't work out so well so I eventually just grabbed my roller
and I went to work. So one thing I didn't mention earlier is that the bookshelf leg is actually
taller than the cabinet by two and a half inches. So this box I'm building does a few things. It
gives the top an elevated look and it also makes up the difference from the bookshelf to the cabinet.
And this piece can be painted whatever color you feel. I just wanted to paint it black.
For the next 30 seconds the video is pretty explanatory so I'm just going to let the video
ride. You guys stay tuned. So I came to the conclusion that this would be the easiest way
and the fastest way for me to line these drawers up and basically shooting a couple pin nails in
them to hold it in place as I come back with a screw to permanently secure it.
And now it's time to install the pull handles. Attach the black box. As I'm installing the
shelf this is where I wish I would have installed the shelves prior so that I wouldn't have to do
touch-up work. So to install the LEDs find a starting point stretch it out and cut the wire.
I actually favorite one side a little too much as I was cutting the wire but I can still make this
work. Even though I gave it a visual look and everything looked fine I still wanted to fire
it up and make sure that it was good before I finish. I applied some hot glue hoping that this
would help secure the solder joint as I'm handling. I even put some glue on the corner to help assist
the sharp bend on the LED strip. I mounted the LED controller on the back side of the black box
and the IR on the side so I can just hold the remote down low and send IR commands.
Four mounting holes should be good enough to secure the bookshelf to the top.
And to secure the opposite side just pull out a drawer
and attach the cabinet to the black box from underneath.
