So Satisfying - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
8 Video Views·Aug 18, 2023
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine restores these broken panes of glass in an antique display cabinet. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration in Gorham, Maine. These are the three
doors of a very nice display cabinet that was damaged when it was being shipped here from
Scotland. I don't have the case here but the customer provided a good photo. As you can see
a lot of glass was broken and that's what the job is to replace that glass.
I think this cabinet the design of the doors of design of these mullions goes back to
Federal period or George III. I think this is more likely a early 20th century
reproduction type piece. It's very well made solid oak. So all right let's get started.
So I'm going to use a heat gun to soften up this putty and work at it with a putty knife.
I kept the heat gun on that putty for about two minutes. I have it set at medium which is about
450 degrees centigrade and I was careful to keep it about 15 centimeters away from the object. I
don't want to harm the wood in any way and took two minutes to get started but then once you go
along you can you can kind of move right along pretty quickly. I use the putty knife as a gauge
using the heat gun to loosen up these bits of putty. It's really important to get every bit
of that old putty. It's going to be difficult enough to fit glass in here without the old
putty getting in the way. Well okay that's one down. I have three more to go on this door
and for the purposes of this video I'm probably just going to show this one door. It's the worst
the other putties but just needs a little extra heat and a little more prodding.
want to soften up like the others but I'll just keep applying more heat to it. Okay that's
that's the first door. I took out four panes of glass and all the putty. It took about four hours
to do that and I'm taking into account the time it takes me to make a video so it's about an hour
a piece and I'll do the next two off camera. I'll tell you it's slow going. This is the second door.
I'm on the third piece. These pieces were big. This putty is really hard. You've got to put a
lot of heat on it to make it soften up. Plus the mullions are very delicate. Yeah the mullions are
just 1.7 millimeters and it's interesting in a lot of corners, not all, but all the corners of
this octagonal piece as I scraped the putty I could see these rectangular dark places
and I quickly saw that what they are are pieces of fabric. They put pieces of fabric across these
joints. I'm imagining it's to strengthen them and I may do the same thing but I'm removing
There's not a lot of room for variance. Okay this is the eighth and final
broken piece to be removed. I'm going to clean up the bench and set it up for cutting glass.
Okay I've got everything I need. A glass cutter, nibbler, scissors, marker,
tape, measuring tape, old glass, square, and a sleeve of restoration glass.
And I almost forgot a cardboard and a utility knife. I'm going to make templates of each
piece on a cardboard. Okay I'm ready to start cutting some glass. Some of those more odd-shaped
pieces I may make templates for on a cardboard. I think I'm going to start with these two small
small rectangular pieces and I think I can measure those directly from these and I'm going to use
this is a piece of glass I took out of the door and I'm going to use that try using that first.
those were the easy ones. Okay sticking to the rectangle theme I'll do this long rectangle.
I found a piece of restoration glass that will work. Well I'm completely frustrated trying to
cut this big piece of glass to make the long pieces of doors. It's about it's about 41 inches
long and I cannot get a clean cut. This keeps happening and I feel like I'm just not getting
a good even score on this length of glass by hand. So I'm checking out YouTube videos.
I called my daughter Emily and she suggested that I take this piece of glass to like the
hardware store where they have the jig for scoring glass and I remember to have a friend
right here in town who has a frame shop. So I'm going to take all this over see if we can get
these cuts done. Hey hi Leah. How you doing? Good thank you so much. Oh you're welcome. Taking on
this glass job. Yeah it's one of those things that can be really hard if you don't have the
right tools. And here's your glass cutter. This is Leah Scotton of the Little Falls Custom Frame
Shop in Gorm, Maine. Okay I'm gonna cut this a little bit too big and then I can go back and fix
butt on this job. But I still have to cut the angles on some of these pieces. Interestingly
when I was asking my daughter about using this glass cutter she said she didn't have a lot of
experience with these. She uses her glass cutting machine for everything. And with Leah here it's
the same way. They can cut all their rectangles on the machine. She didn't even have any good
tools like this. So all on my own. All right thank goodness. I've been forgetting about this little
break in the bullion here. I got to get it glued up. And it's okay to use a conventional
TVA glue for repair like this. These particular spring clamps are great because
they have adjustable tension. And you can adjust it with a screw in here.
And so they can do a delicate clamp like this.
The conventional spring clamp was way too strong. It would destroy that bullion.
Nice. Okay it's time to do the putty. I've got this window glazing putty.
I've got oil colors. Van Dyke brown. I kind of just took one look at this old putty and thought
it's got to be Van Dyke brown. Dixie cup. Plastic cup. Paint thinner. Putty knives.
And the nice thing about this putty is that it takes a long time to dry. It doesn't even
completely dry for ages. But tomorrow after it sets up a bit I can go around and clean it up
a little bit better too. But easier to work with then. All right I let this dry overnight.
Oh it's firmed up quite a bit. Yesterday the putty was so soupy and wet. I was worried about
the fact that I'd added oil color. But let's see what happens. I'll wet the putty knife with
paint thinner. I want to do this big octagonal piece next. I remembered that they had little
pieces of fabric across these joints. You can see the remnants of one of the pieces.
So I've got some cambric which is a type of material you'll see on the bottom of upholstered
pieces. But it's nice and thin. It's got some strength to it. I'll cut some strips that are
3 8ths wide or 9.5 millimeters. I'll cut them two inches. That's 50.8 millimeters. A little bit of
hide glue. Okay I've let that glue dry. All the corners are reinforced. I hope the glass still
fits in there. It does. You can see I've got the door elevated a bit
let this set up overnight. Firm up a little bit before I go around and really clean up the edges
and everything. So now I can get started on the next one. I'm about halfway done. Okay
this door's got all the glass in place. I'll clean the putty up starting tomorrow when it's
firmed up a bit. This door had four broken pieces. That's that's the door with the most.
I'll get on with the next door. Okay these have had a chance to set up overnight so now I can
start cleaning. First thing I want to do is flip it over and clean the other side.
I got to clean up everywhere it squished out.
Actually this cleanup isn't as bad as I thought it was going to be starting off. Once I've
figured out the procedures I'm moving right along here. And I discovered I was having
such a hard time getting the putty smooth and I discovered that once I've got it completely clean
I can use my finger. Well there you go. Three doors to an antique display case or china cabinet.
In a move from Scotland eight pieces of glass were broken. Thank goodness for the
Benheim restoration glass because their glass is indistinguishable from the old glass.
I can't point to these and say which ones were broken. I can actually tell from my putty in the
back but I think they look pretty good. I've got 20 hours in this job and I use these tools and
materials. I'm Tom Johnson, Thomas Johnson Antique Furniture Restoration in Gorm, Maine. Today we're
taking a look at some cabinet doors I restored. These are glass pane doors from a very handsome
federal period secretary bookcase. The doors were damaged when the unsecured bookcase fell
forward to the floor. If you like this video please like it, subscribe, share. Feel free to
repost on other platforms like Facebook or Reddit. I'd appreciate it. Okay I finished doing all the
touch-up work on the mullions. Now I can turn this over and install the existing glass that I have,
the glass that didn't break. I've got to scrape any glue on the inside here from
when I re-glued all these mullions and I still have to clean the old putty off the old glass.
Before I repaired these I put all the glass in where I thought it would go and numbered it off
but it could be different now. We'll find out. I'm going to start refitting them where I think
they belong. Now I've got them all fitted I can start installing them with the glazing putty.
So you just keep kneading the putty until it's a consistent color. It takes a while. I'm just
about there. It feels a little dry to me. I'm just going to add literally just drops of paint thinner.
All right I'm going to take a little bit of this putty. I'm not going to use gloves for
this because I won't be able to get it into the back of the mullion there with gloves on.
I need to roll out the thinnest possible little snake. Okay so I got the thin little pieces down
now I'll take the piece of glass and squish it down as much as I dare. I just realized I can
pick this up and take a look and see if I've got the right amount out. Yeah it looks like
there's just a very very thin layer between the glass and the mullions. Looks good. I can't really
sell for sure until I scrape the excess away but it looks good. Now I put down the larger
amount of putty on the out this side. Okay that's good. I'll let this dry for a couple
days before I take a razor blade and clean it up a little bit but it's not bad.
Anyway I just got about I think 13 or 14 to go.
So
on the second door I've already installed the existing glass but on this door now we have
three pieces that I have to cut new glass for. All right I've got three pieces of antique glass
here. This is glass salvaged out of other furniture that's come in with broken glass.
Now I'm cleaning up and then French polishing the door frames. First I'm sanding with
lightly with just some 500 paper and then French polishing it with my French slack.
There's only one hinge broke. I have the original hinge that goes here and in my collection of old
hinges I have an older hinge that is exactly the same size so that was lucky.
There we go the bookcase section of a secretary bookcase. It fell face forward. The doors were
all smashed. I think it looks pretty good. So now let's deliver it and get it back together
Restoration in Gorham, Maine. This is a nice cabinet. It's a pine cupboard. It's the upper
section of a cupboard. I don't really know how old it is but the case is dovetailed together.
It has this very interesting gothic arch thing going on here but all that's really wrong with
is that the glass is broken here and what this video is about it's about just replacing
this piece of glass. Of course the first step is to take the door. All right I've got a thin
flexible blade putty knife, a stiff putty knife, an old chisel. I really like this heat gun. It's
a hot surface away from combustibles. It has three speeds. I'm going to start with the lowest
speed here which is really it's 50 degrees centigrade. It's kind of like a hairdryer
level of heat. I'm going to start with as low as possible. I don't want to scorch the
wood or anything. I'm going to just put a piece of plywood here to protect it.
I think the heat at least the heat I'm going to start with is too low to scorch the wood.
Hopefully it will soften the putty. Well the low heat doesn't seem to be doing anything but
you know that's where you start. See if it'll work. I'll go to the next setting which is 450
degrees centigrade. I have no idea what that is in Fahrenheit. I'm going to try it. All right it
didn't take long at all for the second setting to start to soften this up. So as it gets warmed up
it actually gets easier and easier and I'm able to start the putty knife right at the top edge
and then kind of use using the putty knife as a heat shield. I just do that area and it peels away.
Well I'm glad that's done. That took about an hour but it pays off to be careful. My goal
is to save this piece of glass although it did crack while I was working on it.
And there it cracked again. I'll try to save these pieces as best I can. I mean obviously
this is antique glass and if I have a job that needs a smaller piece I can use it.
And now I'll go find some glass to put in here. I have a collection of antique glass. I don't think
any of the pieces are going to be this big but I have a restoration glass from Ben Himes in New
Jersey that looks just like this. Okay up in the barn I do have some restoration glass that I
mentioned but I found a rather large piece of antique glass and so I think it'll be the right
size. So the next question is you know the the old glass has a it's real wavy and has a lot of
I need to see if this glass that I saved from another job has the same level of defects.
So here's a piece of the old glass and you can really see how wavy it is. It's got a pretty
good wave to it. I think that'll work. Yeah I think that'll work fine. Okay now this is not
a video about how to cut glass. This is a video about me trying to cut glass.
Failure. Okay so I failed with the antique glass but now I'll use a piece of the restoration glass
which is really nice and actually just as wavy as the old glass so it's fine.
I think I wasn't scoring the glass evenly enough and I'm also kind of learning how
Okay so the glass fit in pretty well thank goodness. Now I've got some window glazing
compound. I have some dry colors so I can mix it to this color. Some paint thinner and a putty knife
really dry but it'll dry some and then allow me to go around and clean the glass
and scrape these edges get it all nice and clean. Okay it's dried overnight. You know it's still
soft but it's firmed up quite a bit and I think enough for me to clean this glass as long as I'm
fine. I forget which paint it was I replaced but it was this one and boy it looks pretty good.
