Can you prusik double ropes?

HowNOT2
100 followers
May 13, 2023
Having a prusik around 2 ropes can be for a handful on contexts, but this was looking through the view point of a SAR (Search and Rescue) lens. This was part of more testing that day and you can see "Can you evenly tension two ropes?" at https://youtu.be/H0M6F16vWTA. Thank you Matt O'Donnell for visiting the lab and doing this with us.
👉 10% supports us at https://www.extremegear.org/
👉 10% off Rocky Talkie by clicking https://www.rockytalkie.com/HowNOT2
👉 Our merch is at http://www.hownot2swag.com/
👉 1000 Patrons makes us viable https://www.patreon.com/howNOTtoHighline
👉 1 time donations really help also https://www.paypal.com/paypalme/slackcessfund
If you wrap a prusik around a rope, it'll typically slip before the prusik breaks.
It usually doesn't grab the rope strong enough in order to break the rope itself.
Now what happens if you want to tension two ropes at the same time?
If you wrap the prusik around both ropes, will it slip before it breaks,
or will it break the rope, or will it even grab it all?
This is just an old strand of rope we were testing with earlier today.
So it's dead-ended here to a fixed point below the cell.
This is a single three-wrap prusik around both ropes.
We're going to choke it up.
We're going to set it hard, just like we did out there.
And the goal is to see what it fails at.
I assume it's going to slide down the rope and come off the ends.
No stopper knots there.
And hopefully it will have enough gripping strength that
we're not worried about it slipping when we use it in real life.
Hopefully it grips, okay.
And then we compare it to a single strand,
and then we'll put it on 11 millimeter, hopefully, which is skinnier.
So the ratio between prusik to host rope is less ideal.
Holy, it's scary to sit next to that.
Ah, 19.78.
That sounded like a 19.78.
I can't hear anything else now.
It, uh, it didn't slip.
Yeah, yeah, that's plenty strong enough.
I'm shocked that the cordage broke before the prusik slipped.
We oftentimes use prusiks like clutches so that if we did hang the basket up,
we would hope to see it slip a little bit before we could overload the system.
Before you overload these ropes.
Yeah, where we hurt somebody potentially,
if they're pinched between the basket and the train, for example.
But that's on single strands.
That is on single strands.
Oh, these are where the rabbits start coming out of the holes.
I would have thought it slid quicker on double strand than it did on single.
Actually grabbed better.
We're just gonna try single strand for comparison's sake.
It's cool how it twists the rope.
What number are we at?
Yeah, yeah, yeah.
And country does.
That's the heartbeat of a prusik.
So what's going to basically happen is eventually this is going to heat up enough
to where one of these will melt to the other, and then it'll go all the way to failure.
Which, of course, I think we should do.
All right, so like duck.
Yeah, the prusik is really long.
I mean, maybe it's not going to melt.
Oh, come on.
It's just so fun.
Yeah, yeah, yeah.
Six, six is here.
Into a cliff at six or seven, you're going to be much more injured than you were.
Yes.
Yeah, you don't want to see six or seven.
No.
So what would you do if you wanted it to slip?
You don't wrap it less.
It wouldn't work.
The haul team needs to be what you're 100% right, actually.
It's good technique on the sharp end of the rope,
keeping that basket clear of obstructions, rigging, clean systems.
But more importantly, the haul team, who oftentimes is not even trained people.
It's just whoever you have on scene that you kind of deputize.
But there's got to be one person on that team that knows
if it suddenly gets harder, we need to stop.
It's not a tug of war where we bear down and pull hard.
Yeah, yeah.
You could absolutely squish somebody between the basket and the train.
Before you slipped.
Yeah.
And then you're actually damaging the rope, too.
Like, that's not good for your rope.
Right.
And the reason we use the process is so that theoretically it's gentler on the rope
than, say, like it gives a sender a rescue sender or a tooth to device.
Gentler, not gentle.
Not gentle, but it shouldn't part your rope.
Yeah.
Without first having some sort of.
I've always called the sheath a shock absorber.
Yeah.
I've seen a prosthetic sheath rope once.
All right.
So now we're going to switch to 11 millimeter hose rope.
All of this gear, by the way, is old.
It's retired.
And that's why we're destroying it here.
The fire department, we're going to take the good stuff.
So bear in mind that these results that we're just comparing apples to apples.
But if you had brand new gear, hopefully the numbers would be better.
Yeah, but it's still pretty good for old gear.
Yeah.
This is old and worn.
So the coefficients of friction between the hose rope and the process can be a little different.
A lot higher.
It's grippier.
It's grippier when it's older.
Yeah.
A hundred percent.
Yeah.
When it's brand new, it slips a little earlier than you might want it to sometimes.
So it looks like we got more surface area, right?
Certainly.
And you're worried about this gap in between not being grabbed.
At least I was.
I mean, look at that.
It just squeezes it together and there is no gap.
Yeah.
So, and again, the material broke.
That prusik did not slip at all.
Yeah, it doesn't slip when you do two.
Yeah.
And this is 11 mil.
Correct.
Yeah.
And we got peak force of 13.23.
This rope is 11 mil.
Yeah, this rope's 11 and this is eight on 11 is...
But we got way less on the prusik and it broke in a different spot.
Well, they could have a huge variety on their own.
Yeah, I didn't expect the material to be breaking.
I thought they would just slip the hitch.
I mean, 13 is still strong.
Yeah.
But it's not slipping.
Let's try single strand.
Single strand.
Oh, it's sliding.
What's it sliding at?
Weird.
So, was it going down the whole time?
Because the inside of the prusik is getting glazed, maybe.
Yeah, I think the inside is getting glazed.
What are your thoughts?
That's how I expected it to perform.
On the other one.
On the other one, yeah.
Me too.
So, I'm happy with it.
That's plenty strong for everything that we're going to do with it.
It didn't have like that hold too tight slip thing.
Oh, neat.
You know what the longevity of this rope is?
So, five minutes in the slack set machine.
Yeah, there you go.
We retire it after 10 years, typically, if it hasn't had a rough life.
So, it's at least 10 years old, probably more like 15.
And in good shape, obviously, in terms of its use and abuse.
I thought what was interesting here is that on that half inch rope,
it kind of had that pulsing skip.
And this one was just a smooth descent.
And I don't know if that's a dynamic of the diameter post rope to prusik,
or just the sheath on this rope is more slippery than on that half inch.
This one, for whatever reason, didn't really get fused.
It's glazed for sure, but it comes off no problem.
It didn't pulse, which is also like it wasn't melting.
Whoa, was that from this test?
Yeah, this was.
Wow, yeah, yeah, because we broke the other one.
Yeah, we've destroyed everything so far.
So, I mean, oh, that's gnarly glazing.
Gnarly.
But it didn't melt like the other one did together.
Not together.
It didn't melt.
Yeah.
Let us know if you guys want this type of content,
because it doesn't get 100,000 views when we make this stuff.
We need to know if you like it.
So put that in the comments below.
Smash stuff that looks like this.
And thanks for watching.
