Home-made Climbing Gear?

HowNOT2
100 followers
2 Video Views·May 3, 2023
Would you trust homemade gear?
👉 10% supports us at https://www.extremegear.org/
👉 10% off Rocky Talkie by clicking https://www.rockytalkie.com/HowNOT2
👉 Our merch is at http://www.hownot2swag.com/
👉 1000 Patrons makes us viable https://www.patreon.com/howNOTtoHighline
👉 1 time donations really help also https://www.paypal.com/paypalme/slackcessfund
Would you take a whipper on some homemade trad gear?
And they kind of resemble ball nuts.
They look kind of bomber and at the same time a little janky.
So we'll find out with our new cam crusher.
I think 3.0 is the version we're on.
It's a much smaller device made out of four inch C channel
that goes all the way around.
And then it has some angle iron on both sides
and some half inch plates in the middle that have horse
hoof files welded to the inside that keeps gear from sliding out.
Because actually our first cam crusher, the cams would slide out,
which was a bummer when I was trying to break cams, but it was insightful
when I learned that the outer pressure doesn't overcome the lack of friction.
So we'll be getting some different types of rock plates
glued to some steel plates on the inside.
And we will see if friction plates roll with different rocks and maybe even wet.
So stay tuned on.
This is more or less the first grand opening of our rock adapter.
And these have been on the to do list for six months to two years.
I actually don't know.
But with our last cam crusher, it wasn't.
It was just too big and too flexible and too weird to do the small stuff.
And this actually will go up to a number four if you overcam it.
A number three perfectly well.
And even with this cam crusher 3.0, we can put some pressure
plates on the inside to see if we actually get four times
pressure going out as we apply in the pole,
which is what the math says we get.
But nothing, as we've learned, is perfectly the way math says it should be.
Let's start with this yellow sort of walnut.
It has two wheels that slide it up and down.
The thumb loop is super good enough, but it's definitely got some
homemade vibes, but I imagine it will hold.
I didn't expect it to break like that.
It still works, except where it doesn't.
And the next one is this blue ball nut hybrid.
And it looks like before we broke it.
So that did not damage it.
It just scratched up, but it's still it's just bent.
Let's get let's get it in there better.
Oh, the head came off.
So those are the wheels.
The nut got crunched.
So these wires were inside that part and it slid up here
and these wires detached from this head.
So the whole thing basically came apart at six kilometers.
So this is a much shorter piece, which I think is a lot better.
If you're aid climbing, you don't want to clip this loop
and then lose all this distance right here.
This looks like a copper head swaging this cable here.
And then that looks like a brass head that doesn't have a lot of range
of when it fits in and when it locks.
So let's pull on it.
The head came off again.
Oh, this this head was hollow.
This is what had the wires in it.
Not a lot, actually a lot of meat there.
And then the brass piece is definitely chewed up.
It's a bend in the wire.
And it pulled out through the bottom and still has some aluminum right here.
So that's why this is completely
just jacked up here.
So this is a cone that slides between these two plates
that have been machined out in the center in order to sandwich this in.
When it's fully squeezed here,
it sticks out all the way up, making this the most narrow.
And then as it comes back in, it spreads those out.
The problem is, as you use it,
this can go all the way down and then you can't get it back in.
It's a two handed thing to get that cone
back in there so you can place it.
But it also has these clamps,
which is definitely what you want in some trad gear.
It's got some exposed wires, which definitely is what you want in your trad gear.
And you want this to look as handmade as possible when you're looking for trad gear.
Look at that graph.
It stayed until about four, fourish.
These things just slipped all the way down the cable.
But then also the cone looks jacked.
That looks jacked.
That looks more messed up.
I think the concept is a nice idea, but I don't know.
What do you guys think?
Would you jump on that?
We've tested a few cams already, which will come out soon.
This actually works really well with cams.
And if you are going to buy cams, please buy them from ExtremeGear.org
because it does really help
allow me to continue to put a lot of energy into that.
If you have cams that you would like to see tested, please go to contact us
on HowNotTo.com and let me know.
I actually have a really cool test that somebody sent in
where I get to break test a recalled alien and recalled aliens
where they had a dimple.
They kind of broke at the stem right up in here.
And it was the talk of the town for a while.
And you don't really see those floating around too often.
So I'm pretty excited that we got our hands on that.
So if you could, like, subscribe, do those things.
And HowNotToSwag.com also helps us out, too.
