When we rigged our CRG 200m experiment (https://www.youtube.com/watch?v=j0ZJjZ9ybkc ) our 50 meter section of pink tube had no backup loops. So @Matthew_McMillan and I set up the same highline configuration in the park and play with different lengths for extenders.
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break. This all couldn't happen without you!
How long do your backup extenders need to be
on your Enov split connections?
Check it out on this episode of How Not to Highline.
Hi, I'm Ryan Jinks and welcome to my gear room.
We set up the Enov split at the park near my house
after doing our experiment at CRG with the 200 meter
where we cut the line.
The problem we had at that experiment
was the pink tube section, the nylon stretchy webbing
had no backup loops.
And we had our typical 50 meter backup
with our five meter extenders.
And so we theorized we either screwed up
or since pink tubes stretches so much
that we need a longer extender.
So we did some experiments in the park
and we mixed up some Feather Pro, Pink Tube and Feather Pro
so we could compare how our backups were acting
with our extender lengths.
So watch this as we explore how long our extenders need to be
for what type of webbing we're using
in our 50 meter segmented highline.
In case you're new to the Enov split idea,
this soft shackle, the red one is crisscross
and we have other videos showing how to do that
which allows us to put this other soft shackle
or a metal quick link in there that's connected
so it can't move in either direction.
The backups are connected to each other.
These two pieces are connected
and these are all connected together.
Everything's redundant and if something were to fail
then you only lose that one section
and you only fall roughly around eight or 10 meters
when you have a mainline failure.
We did an experiment at CRG's 200 meter line
to explore the difference between a continuous line
and an Enov split line.
But this is the technique.
This right here is an extender
which allows the backup to also be 50 meters long.
This is a 50 meter piece
which also has this on the other end over there.
We'll explain all that in detail further on.
Okay, so we have two different kinds of webbings here.
We have Feather Pro with a spider backup.
This is just the extender.
Then we have PinkTube with spider backup.
Spider silk is a very low stretch webbing.
Very, very low stretch, it's vectoring.
This is nylon, stretchy, stretchy nylon, okay?
Right now you can observe that we have lots of loops
in our PinkTube backup.
This is a 50 meter piece as well
but it has a five meter long extender on the other end.
What we discovered when we did our CRG 200 meter experiment
is that we didn't have any backup loops.
And we have a theory that this stretches significantly
at two or three or four kilonewtons
more so than the Feather Pro does.
Which means we had the loops we wanted for the Feather Pro
but we lost them for the nylon PinkTube.
So we're gonna tighten it up here in the park
and explore how much extension we may need
in order to have a number of loops in our backup
for a stretchier webbing.
Hey guys, we tensioned it and got it to three kilonewtons
and about two kilonewtons is what I'll put
most high lines at.
But this demonstrates what we experienced at CRG.
If you look down there, I do have control over this backup
so that's kind of irrelevant since I have the tail end here.
But you'll notice the PinkTube down there
has no backup loops.
But the next section of Feather Pro at the very end
has loops.
So we're at the PinkTube connection here
and you can see that it's being pulled over here.
Not too much, there is, eh, too much.
Once we got to about one and a half kilonewtons
I saw the backup loops disappear
and once we got to three they were completely tight.
This is still loose from the Feather Pro,
doesn't stretch as much.
But when you get on a line,
those backup loops look quite loopy.
But once you get on, this is a high line,
you would end up losing about half of those loops.
So those, I don't, I like the five meters
that we did for that.
As far as this goes, when I get on this,
this is already tight-ish.
Come follow me over here.
This is not too tight.
It's obnoxiously tight, like not impossible to walk.
But this gets a lot tighter the more force I put on this.
If we put this to five kilonewtons
in order to walk this in this park,
this backup would be really tight
and be pulling on our connections really funny.
So I think the theory is we're gonna have to find out
how long our extender needs to be on stretchy material
if you're going to mix.
Not even if you're gonna mix,
you're just gonna use pink tube as the main
and anything for the backup.
We would have to discover what the best number is.
If you've already done some research on it,
please in the comments below,
add what length work for your extenders
depending on the material that you're using.
So we added an additional five meter piece to our backup.
So now we have a total of 10 meters of Dyneema here.
This stuff breaks at seven-ish thousand pounds of force.
Don't know kilonewtons off the top of my head.
This is padded.
I do like padding that when I mirth hitch
because I found if both components are padded,
which this side is not,
then I get almost full strength for what a sew-in loop is
when we connect it to the sew-in loop of the backup.
But we go into that in detail in other videos,
but padded on both sides we found to be very important.
We will slack snap all of this in another episode
to show you how and what is important.
This stuff is full strength.
This is amazing.
I don't pad it,
but I do tape the crap out of it on site.
This is the backup here,
connected directly to that soft shackle.
Extra, this, and then our five meters goes over there.
So our line is pre-set up,
and you can see that has perfectly good backup loops.
And you can see down there
that we have pretty good backup loops.
The last section, we didn't play with our tail yet,
but we did untape the extender so it could slide evenly.
We have all of this extra.
Therefore, this is too long.
So I would say probably half of this distance, maybe.
Let's play with this.
Nope, you need more than half.
I cannot fold this in half,
which is one option is you can come through here
and connect both loops to that point there.
This right here is the sew-in loop padded
and the Dyneema loop padded.
And that gives us a really, really strong braking strength.
And that's what I was referring to earlier.
However, it is better to have something a bit too long
than too short.
It's really hard to fix it.
This is about less than two meters is my wingspan.
And if I took a wingspan out of this, right there,
I could tape this right here and tape it here
and tape it here and tape it here
and get it out of the way
so your foot doesn't get stuck on it.
And then you can make this exactly what you want
after it's rigged.
It's a real pain in the ass to fix this
if it's too short after it's rigged.
You would have to clip a rope to this,
add a 60 meter rope to the other side,
unconnect the soft shackle, and it's not good.
This is much better to just take some excess
if you're not sure.
Or you can go to the park like we are right now
and figure out exactly how much this specific 50 meter needs
and always leave the backup taped to it.
So then you can always just connect it
to your other high lines and super good enough.
How's it feel, Matt?
100 times better.
Think lightly.
Therefore, you shouldn't walk slack lines with backup boots?
In the park.
So we kept bottoming out when we were slack lining on this.
So now we have 4.3 kilonewtons on this.
You can see here that I taped about a wingspan.
So maybe less than two meters.
I taped here to here, which keeps it out of the way.
But we, at 4.3 kilonewtons, lost our backup loops.
We have no more backup loops.
So you have to kind of have it planned out
how much force you're gonna have on this
when you go high lining.
I might just keep these two extenders
or make one single long 10 meter for this
and then just tape it based on what I will need
based on the high line I use it on.
Because sometimes on 300 meter lines,
you want the whole line to have
four kilonewtons before you get on.
And it only peaks at 4.5 kilonewtons.
Whereas short lines start low and peak high.
Because there's not as much stretch until you whip.
But anyways, I think we're gonna have to retape this
to accommodate our dangerous backup loops in the park.
Oh, that's much smarter.
That's way better.
How's it feel?
Great, it's a good system.
It's just gonna take some tinkering.
So let's collaborate and find out what works for your lines.
And maybe we'll make a chart on slackademics.com
on how long our extenders need to be
depending on what webbing we're using.
If you're using the ENOV split,
that means you're generally doing bigger lines.
Bigger lines usually have a minimum
of two kilonewtons standing tension.
And about four or five at the most.
So something that works for that,
right now this is at four kilonewtons.
I could probably pull it in one meter.
I will probably make a nine meter piece for my pink tube.
But we can all work together
and find out what works for all the webbings
so we can have the perfect system.
Slacklining sucks.
Therefore, we should only go highlining.
Hey, thanks for watching.
But don't be an idiot and try to rig your first highline
by yourself until you go with somebody
who knows what they're doing.
This is not a sport you want to try to learn on your own
after watching some idiot on YouTube
that you don't know show you how to do it.
Instead, you can hire this idiot to show you in person
or you can go to slackademics.com
and find a list of over 1,300 slackline groups
from all over the world.
So you can find some people near you you can join up with,
or you can go to festivals,
which is a great place to network
and see a more official rigging style
because they're generally rigged properly.
If you want to help support this channel,
there are t-shirts you can buy.
That's a link in the description below,
or you can donate $1 per episode on patreon.com
or help on PayPal with a one-time donation.
Anybody who helps get involved
gets an exclusive access to my Slack Snap data,
which we now have over 500 break tests done
and all the videos that are correlated with it.
So I appreciate those who get involved
because this channel really couldn't have happened
sustainably without you guys.
Until you have a chance to rig a highline
that requires 50 meter sections connected together,
please follow, like, and subscribe
to make sure you get all of our episodes.
Cheers.
♪♪