⚓️ NOMAD - Canvas Canoe Repair Part 1

Nomad Boatbuilding
98 followers
12 Video Views·May 14, 2018
This is the first of a multi part series describing the general process of cedar canvas canoe resoration. The primary focus is on a 1950's era Chestnut 50 lbs. Special.
My website: https://www.nomadboatbuilding.com
I post daily on Instagram: https://www.instagram.com/nomadboatbuilding/
Support these videos at Patereon: https://www.patreon.com/nomadboatbuilding
Music: "Monks" by Topher Mohr and Alex Elena
Hi, I'm Mark Rutten from Nomad Boatbuilding. Welcome to my boat shop. Over the next series
of videos we're going to be looking at restoring this 1950s era chestnut canoe. So this canoe is
known as the chestnut 50 pound special. Some people call it a Bob's special or Bantam. In the early
days of chestnut canoes you used telegraph in order to put in your orders to chestnut and so
there would be different names for the different grades of canoes. Bob's and Bantam were actually
telegraph codes that were used to specify that you wanted this 50 pound special canoe in either
first grade or the second grade of finish. By the time this was built I believe chestnut probably
abandoned first and second grade finishes and they're just producing canoes in one grade
because the company was definitely going into its decline at that point. Now this canoe required an
awful lot of repairs. At first glance it looked like it was in pretty good shape. That was mainly
because it hadn't been left out to suffer a lot of weathering. However it did have a lot of
structural damage. The in-whales were destroyed. They're broken in multiple places. There were a
number of rib ends that were in rough shape. So I think I replaced somewhere in the neighborhood
of 20 rib ends on this boat. The stems were rotten at the end so those needed some attention.
The in-whales were rotten at the ends. The rub rails were in bad shape all around so they needed
replacement. The keel was also in bad shape. The powder post beetles had gotten to this boat and
there are a number of elements that had been damaged by that. The seats were never very nicely
made but they had beetle damage. I wasn't able to record absolutely everything that happened during
the restoration of this boat. I do do this for a living and I have to try and get the job done in
a timely manner and so I can't always take the time to get the camera rolling and record every
little detail. I'll do my best to sort of educate you along the way as to how I went about things
and you might find there's some footage from other canoe restorations that worked their way in here
to help fill the gaps. The first job in the canoe restoration is really doing a good thorough survey
and figuring out what it is that needs fixing. If you have a clear picture it'll be easier to decide
what the next job needs to be. For instance I needed to do a lot of rib end repairs and I knew
the in whales needed replacing so it made sense to just pull them out entirely and get them out of
my way. However sometimes leaving parts in place that will eventually be removed can be useful in
your process. I can't tell you exactly what's the best thing to do. It really comes with experience
and frankly you change your mind. You learn new things all the time. Sometimes you regret decisions
you made earlier as you move through the process. But to get started we're going to be taking a lot
of this apart. We're going to be removing the in whales, the breast hooks, the seats, the center
thwart, kind of stripping it down to a bare hull. To do that I'm going to have to remove planking
all along the sheer of this canoe and I'm going to try and preserve as much original material in
this canoe as I can. I won't be doing that with a lot of what I call sheer structure because it's
just too far gone and isn't worth it. But in terms of the planking and the rib ends I don't want to
start ripping stuff out. I prefer to do rib repairs as opposed to replacements because even if you get
the same species of wood trying to get it to look the same is impossible. You'll see in one of these
videos that I did some repairs to the rib ends using the same species of wood and it looks
entirely different night and day. But I used some faux finishing techniques to try and make those
ribs look like they hadn't been repaired. You can still see that the repair is there but it's not
glaring at you. This is possibly the most important but most overlooked part of the canoe restoration
process. Cleaning your boat. I recommend a stiff but soft bristle brush and a mild detergent like
dish soap. If you're going to be doing any re-varnishing trisodium phosphate is a really
good idea. It will actually etch your varnish and allow for a better bond. It's very important to
try and dislodge all the dirt that's in there. Use your hose nozzle set on a jet function
and really try and blast all that junk out of your boat. Get up underneath the breast hook along the
stems. Chase it down towards the center of the boat so you can flush it out. I don't recommend
using a pressure washer for doing this unless you have a particularly weak one that you can
use on a very low setting. You can do more damage than good. If all your canoe is upside down and
drying it's not a bad time to return to the stem bins. Now usually there's paint stuck in these
screw heads so using a small awl I would start to clean that up first. Using my awl I try and work
into the corners of this screw head profile. This is a Robertson screw or square drive. Cleaning
those corners out is very important. Next you want to take a screwdriver that fits your screws
and you want to just give them a sharp tap. Not too hard, just enough to try and break any bond
that might exist. Getting the screws out is best done with something that can apply a lot of pressure
and leverage. In this case a Bryson bit fitted with the proper size bit. That way you can really
lean into it and get a good firm grip on the screw, especially if the screw head's a little bit stripped.
I start by just gentle wiggling to try and break that bond. You can see this screw is just
spinning freely. Now if you have a screw that's just spinning freely you might be able to get a
pair of nippers on it. That screw has suffered from galvanic degradation right there. You can
see how it's corroded, not broken. I lucked out on this canoe, but on most canoes you have to use the
same process that we used on the stem bands for getting out the fasteners. Make sure that all
your screw heads are clear of any paint and dirt. It's a good idea to shock them with a screwdriver
and hammer like you saw before, and often a Bryson bit is the best way to get out stubborn screws.
In this case the screws are in good shape and I was able to remove them all with an impact driver,
but that's not often the case. Notice how I used that quick grip clamp to hold the rub rail in
place while I removed the fasteners. If I didn't do that, that rub rail would be popping off there
and flopping all over the place. If I try to keep the rub rails, that could easily damage them.
When you're working alone like I do, sometimes it's a good idea to imagine if you had another
person in the room, what would they be doing right at this moment to assist you? In this case,
another guy would be hanging on to those gunwales and keeping them from falling off.
Thinking through the process like this can not only help you to avoid making stupid mistakes,
but it might lead to some interesting bits of innovation that you can rely on later on in future
projects.
The next step in my repair process is removing the shear planking. I need to get access to all
of the rib ends, and I also need to get at the fasteners that are holding the breast hooks in.
These are my primary tools for taking apart a lot of the parts of the canoe. The pry bar,
I like to keep it sharpened practically to a knife edge, and so that's really great for
sneaking underneath tacks, for prying planking away from the stems, and for prying the ribs
away from the inwales. These nippers I've got the corner ground out of, and that allows me to sneak
it underneath tack heads a little more effectively. Between the three, I get at just about anything.
Pulling some tacks and taking the shear planks off, get under the tack, I try and give it a lift,
and sometimes I've got to come from both sides to pop it out just a little bit. I can take the
nippers, and if I'm lucky they stay put, and I usually put my tool underneath the nippers to
brace the planking so I don't split it out, but it is buried afterwards. I've got a little
shop-made tack lifter here, but I don't find that it works nearly as well, and I feel it makes a
bigger hole in the planking trying to pry those guys out, so I prefer this method. I've been doing
it this way a long time. It's been a while since I've done a canoe, so I'm a little rusty at it
today. I'm putting my hand on the back side and giving some pressure on the back side of the rib
here to keep the canoe from rocking around. On some boats, if this planking is really messed up,
I'll just cut a two-inch swath along the top and remove that, and then put some different
planking in its place. This boat is in pretty nice shape. I kind of like to not do that with it.
I can't get white cedar out where I am. I can only use red cedar,
though I do have a small supply of white on hand. I like to keep it all looking
fairly original if I can. The reason I'm pulling these planks off is because I'm going to replace
the inwales in their entirety, and there's a few rib ends that need some attention,
so I need to expose those a little bit more. There's that plank.
One little tack over here holding it on. Steel tack.
Here we go. Planking's in pretty good shape. I'll try and save it. Steel fastener again.
And to release all these rib ends, most of the time I'm just coming in here with this tool
and trying to get right behind the tack. This guy's very lightly fastened, so I only got one
tack per rib, which is odd. Usually there's two, but we'll do it. Usually I try and pry that rib
forward a little bit and then push it back in and get that tack to pop out. I'd rather pull it out
that way. So again, I use the tool to protect the wood. I pry against the little pry bar here with
my nippers. Sometimes you can just feel this. This is white cedar, and sometimes it can look
perfectly fine, and it's not until you actually start working on it that you can feel that the
wood has rotted a bit. It's particularly spongy, but it's really soft stuff to start with, so
it'd be hard to tell. It should take me about, I don't know, half an hour, 45 minutes to
get the rest of that run of planking off and get the ribs released, and then I can pop the whole
shear structure right out and start my repairs. Okay, I already tried to get this rusty screw
out with an impact driver, and it wouldn't come, so I'll show you the way I do it.
That's really just a shock, and I've been there with my Bryson bit. Put it on tighten.
Try and tighten it just a little bit. Try and get it to wiggle ever so slightly.
Here, saw it move just a smidge, and then bring it in reverse and put a lot of weight on it.
Boom, out she comes. On this side, my screw head broke off, so here's my secret weapon.
I've got a, this is basically a roll pin, and I cut some little saw teeth into the end,
but I cut them in so that it cuts with the drill going in reverse.
That's it for the first part of this canoe restoration series. This video is really all
about just tearing things apart, and that's an awful lot of the job of boat repair is just
taking things apart. Now, you can't just go swinging at it with a sledgehammer. You have
to think about, what am I going to keep? What are we going to get rid of that still needs to stay
here for now? It's a very, it's a slow methodical process. That's one of the things that's kind of
fun about it. Sometimes you learn the hard way that you should have left something behind a
little bit longer, but anyhow, that's all part of the learning, and that's all part of the fun.
The thing to remember is every project is different. Every project presents new challenges.
This is not intended to cover absolutely every aspect of canoe restoration. We're really just
looking at the different challenges that two specific projects were presenting for me. So,
there are other things that can come up. There's other ways to deal with stuff, but
this is what these two projects required, and I think there's some useful stuff in there,
some hopefully educational stuff. The next video, we'll move on to actually doing some repairs to
things. I hope you'll come back and join me for the next one, and if you're having fun, you want
to see more, maybe you can help me out. Come over to Patreon, be one of my supporters. Every little
bit helps. I'd like to be able to put more and more time into doing these videos, so please
subscribe and tap that bell so you know when the next video is up. Thanks for watching.
